Description
Two-component, air drying polyurethane based clear.
Recommended Use :-
This product is recommended Top coat for glossy , uv protection,weather property and also as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system.
Physical Data :-
COLOUR : Clear
FINISH : Smooth & Glossy
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 16 sq.mt / ltr at a DFT of 25 �µ
FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
New concrete should be cured for at least 1 month prior to paint application. Ensure concrete surface is absolutely dry and free from moisture, oil, laitance, dust and dirt. For old concrete, ensure surface is free from oil, grease, algal & fungal growth and any old coating. Sand Blasting on concrete gives the best performance and should be given first preference out of the available surface preparation methods. If blasting is impracticable, Acid Etching with diluted Hydrochloric Acid followed by fresh water washing to be adopted. Seasoned wooden articles should be scuffed with Emery 220/400 to achieve smooth surface. Please refer our Directive Sheet on Surface Preparation.
Application Data
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : Indefinite
COMPATIBILITY : Can be applied on Epoxy primers and oleo-resinous primer and coated / over coated by two component paints like Epoxy, PU, etc.
WALL GUARD PUTTY is a white cement based product with redispersible polymer and functional additives for application on interior and exterior rough plasters to give a smooth finish.
FEATURES :-
WALL GUARD
PUTTY
1. Provides smooth and uniform finish to rough plasters
2. Good Workability
3. Does not require curing with water
4. Good water resistance
5. Good Tensile Adhesion Strength, Compressive Strength and Flexural Strength
6. Controlled water vapour permeability
7. Excellent abrasion resistance
8. Resists growth of algae and fungi on wall
9. Good intercoat adhesion to emulsion paints
RECOMMENDED APPLICATION :-
It can be used on all types of exterior cement plasters/interior walls, asbestos sheets, concrete etc
PRODUCT TECHNICAL DATA :-
COLOURS : White
FINISH : Smooth and Matt
COVERAGE : 2 coats: 10-15sq.ft/KG up to 1.5 mm thickness in two coat
(It may vary from the quoted coverage to factor such as method and condition of application and surface roughness)
DRYING TIME : 6-8 HOURS
GLOSS LEVELS/SHEEN LEVELS : Silky smooth sheen
FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable
SUITABILITY OF THINNER PAINT Use within 24 hrs.
SHELF LIFE 3 years from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
PERFORMANCE DATA :-
ABRASION RESISTANCE : Excellent
WATER RESISTANCE : Excellent
SHELF LIFE : 3 years from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
REMARKS : a) Kindly refer to the MSDS for the Saffro Mellow Coatings And Resinswhich gives detailed information on Safety measures while handling the paint.
b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire.
c) Avoid eye and skin contact. In case of eye and skin contacts, wash with plenty of clean water.
d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention.
e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling the paint.
f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system.
g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application.
h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use.
i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
SUMO ACRYLIC WALL PUTTY It is one of the best products of itâ??s kind available in the market, provides a very strong, durable foundation and brings out the best performance from the finish paints, both in looks and in durability.
FEATURES :-
SUMO Acrylic Wall Putty is a water based, ready-to-use putty meant for filling and smoothenening out cracks and dents on the plastered wall or similar interior surfaces.
a) The putty has special acrylic binders that ensure that it retains a strong grip on the wall surface, thereby increasing the life of thw paint film.
b) It is made using special equipment and technology that ensure smoothness and consistency
c) On account of the puttyâ??s exceptional whiteness and smoothness, emulsions painted over the putty will tend to look richers
d) It also enhances breathability and lesser porosity compared to conventional putty, thus improving paintperformance further
e) It is quick drying, thus ensuring faster completion of jobs
f) It has better alkali resistance, thus making it more suitable for new walls
RECOMMENDED APPLICATION :-
SUMO Acrylic Wall Putty Can be used for priming plastered walls, asbestos, brick work, concrete, etc
PRODUCT TECHNICAL DATA :-
COLOURS : White
FINISH : Smooth and Matt
COVERAGE : 1 coat: 38-40 sq.ft/KG
2 coats: 24-30 sq.ft/KG
(It may vary from the quoted coverage to factor such as method and condition of application and surface roughness)
DRYING TIME : Surface drying time â?? 20 minutes
GLOSS LEVELS/SHEEN LEVELS : Silky smooth & Matt
FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable
SUITABILITY OF THINNER PAINT Use within 24 hrs.
SHELF LIFE 3 years from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Ensure drying time of 1 Week before cleaning.
No. Type
SUMO Acrylic Washable Distemper is a water-based, interior wall paint. It is India's most trusted distemper and gives your walls a delightful, attractive, matt finish.
1 FEATURES SUMO Acrylic Washable Distemper gives good durability and smooth finish. Due to the fast drying properties, quicker completion of painting job is possible. It is available in bright and attractive shades..
2 RECOMMENDED APPLICATION SUMO Acrylic Washable Distemper is an interior wall finish. It can be applied on all type of smooth plaster, false ceiling, asbestos sheets, concrete etc.
PRODUCT TECHNICAL DATA
No COLOURS White & other shades as per shade cards
1. FINISH Smooth and matt
2. COVERAGE On smooth primer masonry surface by brushing
35-40 sq.ft/kg/2 coat
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time - 25-30 minutes
4. GLOSS LEVELS/SHEEN LEVELS Matt
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 12 months from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
Eco HOME Acrylic Distemper gives smooth ,beautiful and matt finish to the wall at an affordable price, It does not come off on the hands or on clothes likechuna thus ensuring bright colourful walls all year long.It is an economical chalk resistance coating.
RECOMMENDED APPLICATION
Used only on interior surface.
PRODUCT TECHNICAL DATA
No COLOURS White & other shades as per shade cards
1. FINISH Smooth and matt
2. COVERAGE On smooth primer masonry surface by brushing
18-20 sq.ft/kg/2 coat
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time 25-30 minutes
4. GLOSS LEVELS/SHEEN LEVELS Matt
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 12 months from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
SAFFRO'S aura Premium Gloss Enamel gives smooth,hard & glossy finish.Its dry film has good adhesion to the surface.It has very good flow and brushability. aura Premium Gloss Enamel is a highly washable paint, thus you can wipe off most common household stains easily
RECOMMENDED USE It is applied on furnitures,drums,barrels,household products,elecrical
motors,doors,windows and variety of other surfaces which are not
subjected to outdoor exposure
FINISH :smooth and glossy
COLOR As per shade card Including White and Black.
COVERING CAPACITY :7 to 9 sq.mt/lit/coat at 30 to 35 micron dry film thickness,depending
(ON SMOOTH MILD STEEL SURFACE) upon shades and surface.
DRYING TIME :Surface dry - Less than 3 hours.
:Hard dry - Less than 15 hours.
Second coat application period -After 10 hours
Above all properties depend upon temperature and humidity.
FLASH POINT :Above 30* C (86 *F)
THINNER RECOMMENDED :SAFFRO Synthetic G.P Thinner
METHOD OF APPLICATION :By Brush or spray at a pressure of 40 to 50 P.S.I
RECOMMENDED PRIMER :For Metal - SAFFRO R/O Z/C metal primer
- SAFFRO Zinc Chrome primer yellow
For Wood - SAFFRO Wood primer white
For Plaster - SAFFRO Cement primer (oil base)
DIRECTION FOR USE Remove dust,grease,oil,moisture,rust and other loose flakes etc.After
priming the surface with recommenden primer with over night drying &
sanding with emery paper,apply SAFFRO SHINE synthetic enamel using
recommended thinner.Allow first coat to dry for minimum 10 hours before
applying second coat.Stir the content thoroughly prior to use
PACKING : 20 Ltr, 10 Ltr,4 Ltr ,1 Ltr, 500 ml,200 ml,100 ml,50 ml.
BUILDER COAT Acrylic Interior | Exterior emulsion is matt finish.
FEATURES :-
BUILDERCOAT Acrylic INTERIOR | EXTERIOR emulsion provides a smooth long lasting rich finish to the INTERIOR & EXTERIOR wall. It is washable and most stain can be removed easily by sponging with mild soap solution. The paint film is having good resistance to fungus and mildew.
RECOMMENDED USE :-
BUILDERCOAT Acrylic INTERIOR / EXTERIOR emulsion is INTERIOR / EXTERIOR wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc.
PRODUCT TECHNICAL DATA :-
COLOURS : White & other shades
FINISH : Smooth and Matt
COVERAGE : On smooth primer masonry surface by brushing
1 coat: 130-160 sq. ft/ltr
2 coats: 80-90 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc)
DRYING TIME : Surface drying time â?? 10-15 minutes
GLOSS LEVELS/SHEEN LEVELS : Matt
FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable
SUITABILITY OF THINNER PAINT Use within 24 hrs.
SHELF LIFE 18 months from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Description
Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The low solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance.
Recommended Use :-
It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc.
Physical Data
COLOUR : Selected industrial shades
FINISH : Semi glossy
SOLIDS BY VOLUME : 80 + 2%
THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80
FLASH POINT : Base : Above 25C Hardener : Above 25C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data :-
MIXING RATIO : Base : Hardener ( As per our recommendations)
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Epoxy Thinner 190
RECOMMENDED DFT : 75-100 mic.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data :-
COLOUR :- Yellow
FINISH :- Matt
SOLIDS BY VOLUME :- 40 �± 3%
THEORETICAL SPREADING RATE :- 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT :- Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) :- SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE :- BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data
MIXING RATIO :- Base : Hardener (As per our recommendation)
APPLICATION :- By Brush / By Conventional Spray
THINNER :- Type 290
POT LIFE :- 3 hours min at 30�° C
RECOMMENDED DFT :- 30-40 �µ.
OVERCOATING INTERVAL :- MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY :- Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Add Thinner Type 290 into the mix, if required, depending on application method, and stir gently for few minutes. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Strain the paint through Nylon filter cloth of 200 mesh size and apply uniformly over the surface. All equipments used for above should be properly clean.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner and ensuring the uniform application. Use quality brushes for paint application.
For Conventional Spray application :-
Thinner : Type 290
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 p.s.i.
For Airless Spray application :-
Thinner : Type 290
Addition : Max 5%
Nozzle Orifice : 0.28- 0.37 mm
Nozzle Pressure : 1400-1800 p.s.i.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
No. Type Pure Acrylic Emulsion with high sheen.
1 FEATURES It provides a smooth long lasting rich finish with high sheen to the interior and exterior wall. It is washable and most stain can be removed easily by sponging with mild soap solution. The paint film is having good resistance to fungus and mildew.
2 RECOMMENDED APPLICATION STAR valvet glow emulsion is an interior and exterior wall finish that can be applied on all type of smooth plaster, false ceiling, asbestos sheets, concrete etc.
PRODUCT TECHNICAL DATA
No COLOURS White & other shades as per shade cards
1. FINISH Smooth and high sheen
2. COVERAGE On smooth primer masonry surface by brushing
1 coat: 140-160 sq.ft/ltr
2 coats: 80-90 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time â?? 10-15 minutes
4. GLOSS LEVELS/SHEEN LEVELS Silky smooth with high sheen
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 3 years from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
PERFORMANCE DATA
No ABRASION RESISTANCE Excellent
1. WATER RESISTANCE Excellent
2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins STAR velvet glow emulsion which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description
Two component Epoxy based anticorrosive primer containing red oxide and zinc phosphate as corrosion inhibiting pigments
Recommended Use :-
This product is recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate corrosion conditions. Not to be recommended for immersed water condition.
Physical Data :-
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 ± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at DFT of 30 �µ
FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C
DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray
THINNER : Epoxy Thinner 190
POT LIFE : 4 hours min at 30C
RECOMMENDED DFT : 30 - 40
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel Finish Paints.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix, gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction.
Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. Add Epoxy Thinner Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean.
For Conventional Spray application :-
Thinner : Epoxy Thinner 190
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 p.s.i.
For Airless Spray application :-
Thinner : Epoxy Thinner 190
Addition : Max 5% if required
Nozzle Orifice : 0.37- 0.42mm
Nozzle Pressure : 1400-1800 p.s.i.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data :-
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description
Two-component acrylic aromatic polyurethane finish coating
Recommended Use :-
This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries.
It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry.
Physical Data
COLOUR : Assorted shades
FINISH : Glossy / Semi glossy / Matt
SOLIDS BY VOLUME : 40 ± 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 µ
FLASH POINT : Base : Above 23 C Hardener : Above 23 C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 DAYS.
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional spray / By Airless Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30 C
RECOMMENDED DFT : 30-40 µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
No. Type SILK Interior Emulsion provides a luxurious finish and a silky glowing appearance to the wall.
1 FEATURES SILK Interior Emulsion is water based, Economical interior emulsion for distinctly rich and smooth finish as compared to distemper. Ideal combination of pigments & extenders mixed in a co-polymer emulsion for smooth and pleasant matt finish with Good washability.
2 RECOMMENDED APPLICATION SILK Interior Emulsion is an interior wall finish that can be applied on all type of smooth plaster, false ceiling, asbestos sheets, concrete etc.
PRODUCT TECHNICAL DATA
No COLOURS White & other shades as per shade cards
1. FINISH Smooth and matt
2. COVERAGE On smooth primer masonry surface by brushing
1 coat: 140-160 sq.ft/ltr
2 coats: 80-90 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time â?? 10-15 minutes
4. GLOSS LEVELS/SHEEN LEVELS Silky smooth sheen
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
No. Type Nano acrylic Interior Wall Primer (Water Thinnable) is an economy water-based primer that enhances the application and finish of interior topcoats.
1 FEATURES Nano Acrylic Cement Primer is water based, Economical interior primer with good whiteness,good coverage and flow and leveling properties.
2 RECOMMENDED APPLICATION Nano Acrylic interior wall primer that can be suitable for priming plastered wall,asbestose,cement concrete etc.
PRODUCT TECHNICAL DATA
No COLOURS White
1. FINISH Smooth and matt
2. COVERAGE 1 coat: 90-100 sq.ft/ltr
2 coats: 60-70 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time â?? 10-15 minutes
4. GLOSS LEVELS/SHEEN LEVELS NA
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
PERFORMANCE DATA
2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description
Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment.
Recommended Use :-
It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion.
Physical Data
COLOUR : Grey
FINISH : Matt
SOLIDS BY VOLUME : 40 �± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation.
Application Data
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray
THINNER : Thinner 290
POT LIFE : 3 hours min at 30�° C
RECOMMENDED DFT : 30-40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320)
COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description
Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating.
Recommended Use :-
This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application.
Physical Data
COLOUR : Industrial Shades
FINISH : Glossy / Semi-glossy
SOLIDS BY VOLUME : 40 + 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr @ recommended DFT of 30
FLASH POINT : Base : Above 23 C Hardener : Above 23C
DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base: Hardener - As per our recommendations
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30C
RECOMMENDED DFT : 30- 40 .
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Description
Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments
Recommended Use :-
It is an ideal primer where faster turnaround of equipment is desired, Hence making it ideal primer for industrial and Infrastructure equipments, heavy machineries etc exposed to medium corrosive and marine environment. It is also recommended for steel structures in Chemical, Fertilizers, Petrochemical and industrial plants. Not to be used for immersion application.
Physical Data :-
COLOUR : Grey, Yellow, Beige, Red oxide
FINISH : Egg Shell
SOLIDS BY VOLUME : 48 ± 3% (Depends on shade)
THEORETICAL SPREADING RATE : sq.mt / lit at recommended DFT of 30 µ
FLASH POINT : Base : Above 23C Hardener : Above 23C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : DRY TO HANDLE: 3 hr's max FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray
THINNER : Epoxy Thinner 190
POT LIFE : 4 hours min at 30C
RECOMMENDED DFT : 30 - 40 µ.
OVERCOATING INTERVAL : MIN : 2 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous Top coats.
Description
Two Component, Air-drying, Epoxy Polyamide Cured Finish Paint.
Recommended Use :-
It Is Recommended As A Top Coat For Structures, Pipelines, Vessels, Equipments And Machineries, Storage Tanks Etc. In Fertilizers And Chemical Plant, Cement Plants, Power Plants, Steel Plants, Pharmaceutical And Petrochemical Complexes, Refineries Etc. Product Is Also Recommended For Application Over Suitable Primer For Oem Industry Like Machine Tools, Pumps, Machineries, Transformers Etc.
Physical Data
Colour : assorted Shades
Finish : glossy / Semi Glossy
Solids By Volume : 40 +3% (depends On Shade)
Theoretical Spreading Rate : 13.33 Sq.mt / Ltr At Recommended Dft Of 30 au Flash Point : base: Above 23 C Hardener: Above 23 C
Drying Characteristics (at 30'c And 65% Relative Humidity) : hard Dry : Overnight Full Cure : 7 Days
Shelf Life : base : 6 Months Hardener : 6 Months
Surface Preparation
This Being A Topcoat, Which Is Applied Over, Primer Or Intermediate Coats, The Surface Should Be Free From Oil, Moisture, Dust And Dirt. Aged Epoxy / Pu Coating Should Be Roughened By Emery Paper Grade 400 / 600 For Better Bonding.
Application Data :-
Mixing Ratio : base : Hardener (as Per Our Recommendation)
Application : by Brush / By Conventional Spray / By Airless Spray
Thinner : 190
Pot Life : 4-6hrs Min At 30 C
Recommended Dft : 30-40 U
Over Coating Interval : min : 8 Hours Max : 24 Hours
Compatibility : can Be Over Coated With Pu, Chlorinated Rubber And Synthetic Enamel Paints.
Description
Two component, air-drying, Epoxy polyamide cured finish paint.
Recommended Use :-
It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc.
Physical Data
COLOUR : Assorted Shades
FINISH : Semi glossy
SOLIDS BY VOLUME : 40 �± 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr at recommended DFT of 30 �µ
FLASH POINT : Base: Above 23�° C Hardener: Above 23�° C
DRYING CHARACTERISTICS : SURFACE DRY : 90 minutes max HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : 190
POT LIFE : 4-6hrs min at 30 �° C
RECOMMENDED DFT : 30-40 �µ
OVER COATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with PU, Chlorinated rubber and synthetic enamel paints.
Description
Two-component air-drying intermediate/primer surfacer coat.
Recommended Use :-
Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.
Physical Data :-
COLOUR : Grey, White
FINISH : Egg Shell to Matt
SOLIDS BY VOLUME : 40 �± 3%
SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ
FLASH POINT : Base : 23�°C Hardener : 23�°C
DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.
Application Data :-
MIXING RATIO : Base: Hardener ( As per our recommendation)
APPLICATION : By Brush/ By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30�° C
RECOMMENDED DFT : 30 -35 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
Description
Two component air drying aromatic polyurethane finish coating
Recommended Use :-
It is recommended as topcoat for Original Equipment Machines, Hygienic, Maintenance painting where mild chemical resistance along with good abrasion resistance and decorative finish are required. Sometimes it is recommended as undercoat of finish coats application for economic benefits.
Physical Data
COLOUR : Assorted shades
FINISH : Glossy / Semi glossy / Matt SOLIDS BY
VOLUME : 40 �± 3% (Depends on shade) THEORETICAL
SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30
FLASH POINT : Base : Above 23C Hardener : Above 30C
DRYING CHARACTERISTICS : SURFACE DRY :20 - 30 minutes (At 30C and 65% Relative humidity) HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being a Topcoat, which is applied over underneath primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 followed by solvent wipe for better bonding.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional spray / By Airless Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30 C
RECOMMENDED DFT : 30-40
OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Nano Acrylic Cement Primer is water based, Economical interior primer with good whiteness,good coverage and flow and leveling properties.
RECOMMENDED APPLICATION
Nano Acrylic interior wall primer that can be suitable for priming plastered wall,asbestose,cement concrete etc.
PRODUCT TECHNICAL DATA
No COLOURS White
1. FINISH Smooth and matt
2. COVERAGE 1 coat: 90-100 sq.ft/ltr
2 coats: 60-70 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time â?? 10-15 minutes
4. GLOSS LEVELS/SHEEN LEVELS NA
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
ULTRA PREMIUM weatherproof interior and exterior emulsion is a smooth, water-based, modified acrylic, interior and exterior wall finish with silicon additives.
FEATURES :-
ULTRA PREMIUM weatherproof interior and exterior emulsion is specially formulated to withstand extreme tropical conditions of rainfall, humidity and heat
ULTRA PREMIUM provides excellent resistance from growth of algae and fungi on the walls. This prevents appearance of black spots due to algal growth.
ULTRA PREMIUM provides extremely good protection against alkali and UV degradation, thus ensuring that the shade doesnâ??t fade for a long time and the paint lasts longer.
RECOMMENDED USE :-
ULTRA PREMIUM Acrylic interior and exterior emulsion is interior and exterior wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc.
PRODUCT TECHNICAL DATA :-
COLOURS : White & other shades
FINISH : Smooth and soft sheen
COVERAGE : On smooth primer masonry surface by brushing
1 coat: 140-170 sq. ft/ltr
2 coats: 85-95 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc)
DRYING TIME : Surface drying time â?? 30 minutes
GLOSS LEVELS/SHEEN LEVELS : Silky smooth with soft sheen
FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable
SUITABILITY OF THINNER PAINT Use within 24 hrs.
SHELF LIFE 18 month from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
PERFORMANCE DATA :-
ABRASION RESISTANCE : Excellent
WATER RESISTANCE : Excellent
REMARKS : 1) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire.
2) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water.
3) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention.
4) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling the paint-this is required for all paints.
5) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system.
6) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application.
7) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use.
8) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description
SAFFRO MELLOW COATINGS & RESINS MELLOWTEX RUSTIC/DHOLPURI/BUBBELS is a textured finish composed of high quality durable acrylic modified resin specially designed as an intermediate coating. RUSTIC imparts a super premium look to the walls.
BENIFITS :-
Hides Fine Cracks
It hides surface undulations and fine cracks.
Tough Textured
The tough texture finish lasts for long and ensures low maintenance.
Plaster Protection
It increases the life of plaster by protecting it from wind driven rain.
UV Resistance
It has excellent UV resistance and adhesion.
Anti-algal Formula
It resists fungal and algal growth when applied as system, with the recommended top coat.
Technical Information :-
Drying time: Surface dry time 30 - 60 min.
Flash point IS101/1987 Part 1, Sec 6: NA.
Coverage :-
Pre-painting Steps
Plaster New masonary surfaces must be allowed to cure completely. It is recommended to allow 28 days as the curing time for new masonary surfaces.
Cleaning
Surface should be free from any loose paint, dust or grease. Growths of fungus, algae or moss should be removed by wire brushing and water. When the underlying surface exhibits chalkiness, in spite of thorough surface cleaning, use Saffroâ??s Exterior Primer.
How To Apply :-
On normal masonary surface by a trowel spatula to obtain an even coating of 1 to 1.5 mm ,2 coats 2 to 2.5 sq.ft/kg**
(**Actual coverage may very from the quoted coverage due to factors such as method and condition of application and surface roughness and porosity.)
Filling For Holes & Dents :-
In case of dents and holes use Saffro Mellow Coatings & Resins SUMO Acrylic Wall Putty or white cement and fine sand in the ratio 1:3.
Saffro Mellow Coatings & Resins,MELLOW TEX RUSTIC should not be applied on surfaces / substrates that are subjected to continuous seepage or dampness.
Two component air drying Epoxy based clear primer with Polyamide as curing agent.
Recommended Use :-
This product is recommended as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system.
Physical Data :-
COLOUR : Clear
FINISH : Smooth & Glossy
SOLIDS BY VOLUME : 50 �± 3%
THEORETICAL SPREADING RATE : 20 sq.mt. / ltr. at a recommended DFT of 25 �µ
FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Thorough surface preparation is vital. For best results, saffro recommends mechanical preparation techniques (Eg. mechanical scarifying, grit or sand sweeping),
a) New Concrete Surface :-
New concrete surface should be at least 28 days old and/or have moisture content of less than 5% before proceeding with primer application. Laitance and deposits on new concrete are best removed by light grit blasting, mechanical scarification or grinding. Acid etching may be considered for smaller areas, after etching the floor, it should be thoroughly washed with clean water, and then allowed to dry.
b) Old Concrete Floors :-
Mechanical cleaning methods are strongly recommended on old concrete surfaces, particularly their heavy contamination by oil and grease has occurred or old coatings is present. To ensure good adhesion, all contaminants are removed and the surface thoroughly cleaned of all dust and loose debris. A thorough detergent wash is also recommended followed by thorough cleaning with water and moping it off to a dry state.
Universal stainer are manufactured to stiff specification such colour shade, colour strength and rheology. This assures both excellent colour accuracy and colour reproducibility. Universal stainer are sensibly formulated to provide hassle free use. The pigments are highly dispersed to achieve maximum tinting strength and full chroma. Our unique dispersion technique provides each pigment its optimum color development. This result in maximum tinting strength and maximum transparency. This sureties complete de-agglomeration resulting in no shade change & strength change.
Universal stainer are glycol based binder free pigment concentrate having both non-iconic & anionic wetting agent & dispersing agent in optimum dosage.
Packaging Size: 50ml., 100 ml., 200ml., 110gm. , 80gm., 30kg, 50kg, 200kg
WALL BIND ACRYLIC Cement Primer Water Thinnable
No. Type WALL BIND Acrylic Interior Wall Primer (Water Thinnable) is suitable for useas a primer for painting of waterbased wall finishes such as distemper and plastic emulsions.
1 FEATURES WALL BIND has a special features are better whitness and opacity, easy brushing, excellent covering,alkali resistance,quick drying and good filling properties. Provides superior hiding and superior whiteness.
2 RECOMMENDED APPLICATION WALL BIND can be used for priming plastered wall,asbestose,brick work,cement concrete etc.
PRODUCT TECHNICAL DATA
No COLOURS White
1. FINISH Smooth and matt
2. COVERAGE 1 coat: 130-140 sq.ft/ltr
2 coats: 80-90 sq.ft/ltr
(It may vary due to factors such as methods and conditions during application and surface roughness etc.)
3. DRYING TIME Surface drying time â?? 10-15 minutes
4. GLOSS LEVELS/SHEEN LEVELS NA
5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable
6. SUITABILITY OF THINNER PAINT Use within 24 hrs.
7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
PERFORMANCE DATA
2. REMARKS a) Kindly refer to the MSDS for the saffro mellow coatings & resins Nano Acrylic Cement Primer which gives detailed information on Safety measures while handling the paint. b) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. c) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. d) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. e) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling. f) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. g) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. h) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. i) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
WALL PROTECT Exterior Primer is a water-based wall coating suitable for application on exteriors as an undercoat to exterior emulsions.
FEATURES :-
1. Excellent opacity and whiteness
2. Improves appearance of top coat
3. Does not chalk and can be applied on adequately cured fresh plaster
4. Does not require curing with water
5. Provides excellent adhesion to top coat emulsions
6. Prevents peeling off of top coat emulsions
RECOMMENDED APPLICATION :-
It can be used on all types of exterior cement plasters, exterior ceilings, asbestos sheets, concrete and existing painted surfaces.
PRODUCT TECHNICAL DATA :-
COLOURS : White
FINISH : Smooth and Matt
COVERAGE : 1 coat: 120-140 sq.ft/LTR
(It may vary from the quoted coverage to factor such as method and condition of application and surface roughness)
DRYING TIME : Surface drying time â?? 4-5 HOURS
GLOSS LEVELS/SHEEN LEVELS : Silky smooth sheen
FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable
SUITABILITY OF THINNER PAINT Use within 24 hrs.
SHELF LIFE 18 months from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat.
Description
Two component Epoxy based anti corrosive primer pigmented with Zinc Chromate as corrosion inhibiting pigments.
Recommended Use :-
It is recommended as primer on M.S surface for original equipment manufacturing as well as for process industry as in various fertilizer, refineries, petrochemical, chemical and other plants, applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application.
Physical Data
COLOUR : Assorted
FINISH : Matt
SOLIDS BY VOLUME : 40 ± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ
FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C
DRYING CHARACTERISTICS : SURFACE DRY : 60 90 minutes
(At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray
THINNER : Epoxy thinner 190
POT LIFE : 4 hours min at 30 C
RECOMMENDED DFT : 30 - 40 au.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth of 100 mesh size and apply uniformly over the surface. All equipments used for above should be properly cleaned.
Application :- By Brush / By Conventional Spray / By Airless Spray
Generally no thinner is required for Brush application, however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in criss-cross manner and ensure the uniform application. Use quality brushes for paint application
For Conventional Spray application :-
Thinner : Epoxy Thinner 190
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 psi
For Airless Spray application :-
Thinner : Epoxy Thinner 190
Addition : 10-15%
Addition : Max 5% if required
Nozzle Orifice : 0.37- 0.42mm
Nozzle Pressure : 1400-1800 psi
Description
Two component Epoxy based anti corrosive primer containing red oxide and zinc chromate as corrosion inhibiting pigments
Recommended Use :-
Recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate service conditions. Not to be recommended for immersed water condition
Physical Data
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 + 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 FLASH POINT : Base : Above 23C Hardener : Above 23C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : SURFACE DRY : 60 - 90 minutes HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Epoxy Thinner 190
POT LIFE at 30�°C : 4 hours min at 30�°C
RECOMMENDED DFT : 30 40 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel finish paints.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application.
For Conventional Spray application :-
Thinner : Epoxy Thinner 190
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 p.s.i.
For Airless Spray application :-
Thinner : Epoxy Thinner 190
Addition : Max 5% if required
Nozzle Orifice: 0.37- 0.42mm
Nozzle Pressure : 1400-1800 p.s.i.
Product Data Sheet
GENERAL DESCRIPTION
An easy-to-use, water-based primer specifically formulated to �¢??lock-out�¢?? corrosion on a wide range of metals. Applied correctly, is guaranteed for years.
USES
Suitable on sheet metal, castings, wrought iron, TNT Bar, steel Bar and steelwork. This product is not recommended for automotive use.
COLOURS
Available in natural green.
SIZES
Available in 4 litre,10 litre and 20 litre
COVERAGE
Up to 14 square metres per litre depending upon surface porosity and application method.
APPLICATION
Roller, brush, dip or airless spray. Provide adequate ventilation during use.
DRYING TIMES
Touch Dry Time - 20 minutes. Recoat Dry Time - 2 hours. Drying times refer to normal conditions (30�?�°C, 50% humidity). Under cooler, humid or still conditions, longer drying times may be necessary. DO NOT USE IN TEMPERATURES BELOW 10'c OR ABOVE 45C.
DANGEROUS GOODS CLASSIFICATION
Not classified as Dangerous Goods.
SURFACE PREPERATION
Previously Painted Surfaces :
Scrape off loose and flaking paint and make sure the remainder is firmly attached. Sand glossy surfaces and enamels thoroughly and wipe clean. Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer.
TNT BAR,STEEL BAR AND IRON:
Remove all grease, dirt and other surface contaminants.Remove all rust by abrasive blasting or mechanical sanding. Treat any remaining rust with. Prime treated and bare areas with one coat SAFFRO Anti-Corrosive Metal Primer. In highly corrosive environments or within 2 kilometre of the sea, apply 2 coats of SAFFRO Anti- Corrosive Metal Primer
Description
Two components, air drying, high build Epoxy primer. The product has the advantage of epoxy resin composition with specialty pigments, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to be completely wet and provide maximum intimacy with the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. With the high solids and less solvent content of the coating the risk of lifting, blistering, pin holing is reduced, and thus the risk of adhesion failure is minimized.
Recommended Use :-
It is recommended for steel structures in industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc.
Physical Data
COLOUR : Selected Industrial shades
FINISH : Matt
SOLIDS BY VOLUME : 63 + 3%
THEORETICAL SPREADING RATE : 8.4 sq.mt / lt at a recommended DFT of 75
FLASH POINT : Base : Above 25C Hardener : Above 25C
DRYING CHARACTERISTICS (At 30C & 65% Relative Humidity) : HARD DRY : 16 - 18 hours FULL CURE : 7 days
SHELF LIFE : Base: 6 months Hardener: 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible than manual cleaning by mechanical methods like wire brush, emery paper, hand / power tools, etc. to achieve St-2 / St-3 cleaning standards of Swedish specification. The surface should be free from moisture, oil, dust and dirt and should be absolutely dry before painting. Removal of loose rust is a must.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation )
POT LIFE : 2 hours at 30�°C
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Epoxy Thinner 190
RECOMMENDED DFT : 75-100 �µ.
OVERCOATING INTERVAL : MIN : 8 hrs. MAX : 24 hours (In case it is exceeded, the surface should be roughened byemery scuffing)
OVERCOATABILITY : Epoxy, PU, Chlorinated Rubber and Synthetic Enamel intermediate &finish coat.
Description
Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments
Recommended Use :-
It is recommended as primer on M.S surface for OEM's as well as for process industries like fertilizers, refineries, chemicals and other plants. It can also be applied in diverse areas of tank exteriors, equipments, pipelines, structural steel, etc. Not to be used for immersion application.
Physical Data :-
COLOUR :- Yellow
FINISH :- Matt
SOLIDS BY VOLUME :- 40 �± 3%
THEORETICAL SPREADING RATE :- 13.33 sq.mt. / ltr. at recommended DFT of 30 �µ
FLASH POINT :- Base : 23�°C Hardener : 23�°C
DRYING CHARACTERISTICS :- SURFACE DRY : 60 to 90 minutes
(At 30�°C & 65% Relative Humidity) :- HARD DRY : Overnight. FULL CURE : 7 Days
SHELF LIFE :- BASE : 6 months HARDENER : 6 months
SURFACE PREPARATION
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application
Application Data
MIXING RATIO :- Base : Hardener (As per our recommendation)
APPLICATION :- By Brush / By Conventional Spray / By Airless Spray
THINNER :- Epoxy Thinner 190
POT LIFE :- 4 hours min at 30�°C
RECOMMENDED DFT :- 30 - 40 �µ.
OVERCOATING INTERVAL :- MIN : 8 Hours MAX : 24 Hours
COMPATIBILITY :- Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous topcoats.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction. Add Epoxy Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly cleaned. Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. . Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application.
For Conventional Spray application:-
Thinner : Epoxy Thinner 190
Addition : 10-15%
Nozzle Orifice : 1.2 1.4 mm
Nozzle Pressure : 40 - 70 p.s.i.
For Airless Spray Application:-
Thinner : Epoxy Thinner 190
Addition : Max 5%
Nozzle Orifice : 0.37- 0.42mm
Nozzle Pressure : 1400-1800 p.s.i.
Description
Two component metallic zinc rich epoxy high performance primer.
Recommended Use :-
The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time.
Physical Data
COLOUR : Grey
FINISH : Matt
SOLIDS BY VOLUME : 50 �± 3%
THEORETICAL SPREADING RATE : 10 sq.mt / ltr at DFT of 50 �µ
FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C
DRYING CHARACTERISTICS (at 30�°C & at 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Epoxy Thinner 190
POT LIFE : 4 hours min at 30�°C
RECOMMENDED DFT : 30 50 µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : Infinite
COMPATIBILITY : Compatible with Epoxy, PU, Chlorinated Rubber intermediate/finish coat.
Description
Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance.
Recommended Use :-
It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc.
Physical Data
COLOUR : Selected industrial shades
FINISH : Semi glossy
SOLIDS BY VOLUME : 80 �± 2%
THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ
FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C
DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data :-
MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Airless Spray
POT LIFE : 2 - 3 hours min at 30�° C
RECOMMENDED DFT : 75-100 mic.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU
