Description
Two-component air-drying intermediate/primer surfacer coat.
Recommended Use :-
Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.
Physical Data :-
COLOUR : Grey, White
FINISH : Egg Shell to Matt
SOLIDS BY VOLUME : 40 �± 3%
SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ
FLASH POINT : Base : 23�°C Hardener : 23�°C
DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.
Application Data :-
MIXING RATIO : Base: Hardener ( As per our recommendation)
APPLICATION : By Brush/ By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30�° C
RECOMMENDED DFT : 30 -35 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
A two-pack polyurethane quick drying primer cum surfacer with excellent filling & sanding properties for application on wood (hard & soft) & wood substitutes like particle board, veneer, plywood etc. The formulation contains mixed isocyanate hardeners, inert & smooth sanding extenders. When used in combination with Maxiwood 2 PK PU Topcoat, the product gives an extremely rich finish. Presence of plasticizer in the formulation of Maxiwood 2 PK PU Primer Surfacer make the product flexible enough to withstand woods dimensional variation thus enhancing adhesion.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
BCPL manufactures 990 Ltr water capacity tanks. The manufacturing unit is equipped to design and manufacture tanks up to 3000 liters of water capacity. These tanks are heat-treated in a state-of-the-art NC control furnace and painted with polyurethane paint with an undercoat of epoxy primer. The powder coated surface is also supplied on request. These cylinders are supplied to Indian oil and marketing companies such as Indian Oil Corporation, Hindustan Petroleum, Bharat Petroleum and to companies such as TOTAL, Super Gas and exported to other countries.
PU Primer White Fire Retardant Wood Paint
PU Low Voc Sealer Primer Wood Peinture Vernis
Supplier: Paint, varnish, industrial coatings, flooring epoxy, epoxy primer, epoxy self leveling, nitrocellulose paints, heat resistant coatings, wood coatings, pu coatings, enamels, emulsions
Buyer: Titanium dioxide, pigments, additives and resins
A quick drying nitrocellulose primer cum surfacer designed for wood or wood substitutes. The product has excellent filling & sanding property in addition to its protective value. Quicker drying feature along with superior filling & sanding properties make it ideal for high out-put requirement as well as rich finish when used in combination with Maxiwood NC pigmented topcoat.
SU-EPO-PRIME 10: is a two pack polyamide-cured epoxy primer containing Zinc Chrome as a corrosion inhibiting pigment. Primer is designed to give outstanding corrosion resistance and adhesion. It cures to a hard and tough film with excellent physical and mechanical properties. This product is universally recommended for direct application on Ferrous metals, suitably treated light alloys or galvanized surfaces, after proper surface preparation. Primer can be overcoated with epoxy and polyurethane intermediate coats and top coats. Two pack Epoxy-polyamide Zinc Phosphate Red Oxide Primer, direct application on ferrous metals. 2) SU-EPO-PRIME 20: is a two component Epoxy cold cured Zinc Chromate Primer with outstanding corrosion resistance and adhesion. Primer cures to a hard and tough film with excellent physical and mechanical properties. This product is universally recommended for direct application on Ferrous metals, suitably treated light alloys or galvanized surfaces, after proper surface preparation. Primer can be overcoated with our epoxy and polyurethane intermediate coats and top coats. 3) SU-EPO-PRIME 30: is a two component Epoxy cold cured Zinc Phosphate primer with outstanding corrosion resistance and adhesion. Primer cures to a hard and tough film with excellent physical and mechanical properties. This product is universally recommended for direct application on Ferrous metals, suitably treated light alloys or galvanized surfaces, after proper surface preparation. Primer can be overcoated with our epoxy and polyurethane intermediate coats and top coats. 4) SU-EPO-PRIME 31: is a two pack Epoxy cold cured Zinc Phosphate primer with high film build outstanding adhesion and corrosion resistance. Primer cures to a hard and tough film with excellent physical and mechanical properties. It is ideal for application in areas where higher thickness is recommended for achieving optimum performance. This product is universally recommended for direct application on mild steel or suitably treated light alloys or galvanized surface, after proper surface preparation. 5) SU-EPO-PRIME 32: is a two pack high solids polyamide cured epoxy resin surface tolerant primer with outstanding corrosion resistance. Primer contains good amount of anticorrosive pigment. It is ideal for application in areas where higher thickness is required for achieving optimum performance. The primer can be over coated with epoxy, chlorinated rubber or polyurethane topcoats. Primer has good adhesion to steel, galvanized steel and non ferrous metals. 6) SU-EPO-PRIME 40: is a two pack epoxy polyamide clear primer, recommended for direct application on concrete & wood substrates.
