Description
Two component Epoxy based anticorrosive primer containing red oxide and zinc phosphate as corrosion inhibiting pigments
Recommended Use :-
This product is recommended as a primer on suitably cleaned mild steel surface in various fertilizer units, refineries, chemical and other plants, transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, etc. for application on tank exteriors, structural steel, pipelines, machineries, vessels, etc. The product is recommended as a primer for mild to moderate corrosion conditions. Not to be recommended for immersed water condition.
Physical Data :-
COLOUR : Red
FINISH : Matt
SOLIDS BY VOLUME : 40 ± 3%
THEORETICAL SPREADING RATE : 13.33 sq.mt. / ltr. at DFT of 30 �µ
FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C
DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendations)
APPLICATION : By Brush / By Conventional Spray
THINNER : Epoxy Thinner 190
POT LIFE : 4 hours min at 30C
RECOMMENDED DFT : 30 - 40
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated Rubber and Synthetic Enamel Finish Paints.
Application Method
Stir the Base part thoroughly. Mix the base and hardener as per our recommended ratio, by volume. Stir the mix, gently to attain homogeneity. Allow the mixture to stand still (maturation) for about 10-15 minutes to initiate the reaction.
Application : By Brush / By Conventional Spray / By Airless Spray Generally no thinner is required for Brush application; however under adverse environmental conditions about 5% of thinner, by volume, can be added. Apply evenly in crossed manner, ensuring the uniform application. Use quality brushes for paint application. Add Epoxy Thinner Thinner into the mix, if required, depending on application method, and stir gently for few minutes. Strain the paint through Nylon filter cloth and apply uniformly over the surface. All equipments used for above should be properly clean.
For Conventional Spray application :-
Thinner : Epoxy Thinner 190
Addition : 10-15%
Nozzle Orifice : 1.2 -1.4 mm
Nozzle Pressure : 40-70 p.s.i.
For Airless Spray application :-
Thinner : Epoxy Thinner 190
Addition : Max 5% if required
Nozzle Orifice : 0.37- 0.42mm
Nozzle Pressure : 1400-1800 p.s.i.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Supplier: Cotton yarn, cotton and poly cotton fabrics, recycled yarn , grs certified , shoddy , wool waste , bed sheets, towels, kitchen towels, knitted bed sheets , jersey sheets, woven bedding, spinning waste, rice, sugar, cement, clinker, frozen chicken, frozen beef, edible oils, palm oil, wheat, soybean, corn, barley, bitumen, copper cathode, urea, aluminum ingot, sulfur, coal, ores, dap, pet coke, fertilizers, npk, base oil, petroleum products , mattress cover , pillow , micro fibre bed sheets , quilt , pink salt , himalayan salt
Services: Sourcing
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
Steel
Supplier: Soda ash, urea 46 fertilizers, adblue, lead ingots, lead powder, npk fertilizers, rock phosphate, gypsum, base oil, white spirit, potassium chloride kcl, ammonium nitrate, ammonium sulphate, caustic soda, , triple super phosphate (tsp), potassium chloride (mop), diammonium phosphate (dap), sulphate of potash (sop), commercial epsom salt (ces), melamine, urea melamine formaldehyde, urea formaldehyde concentrate 85%, para formaldehyde 96%.
Services: General trading in raw materials, supply chain, contracting.
Buyer: Chemicals, petrochemicals
Supplier: Brass components ,brass precision part,brass cable glands, brass molding insert,brass stop plugs,brass ppr inserts,brass hardware, brass & metal nozzles,brass nipples, brass sanitary part,brass bush and brass products,brass anchors & fasteners, brass lock nut & check nuts & dome nuts, brass turned components,brass inserts, brass auto parts, brass threaded stud, brass forging components, brass forging metal turning parts, brass shower header wall bracket socket,brass electrical components,brass shower hinges pipe to glass connector,brass shower header clamp,brass knob,brass pipe bush,brass guide bush,brass parts,brass tuned components,brass and metal precision parts,brass,ms,ss elbow fitting,brass terminal box connector,brass tee,brass,ms,ss,aluminium stand off(spacers),brass&ms&aluminium &steel metal adapter,brass&ms & aluminium & steel precision turned components,brass & ms& aluminium & steel & metal nuts, bolts, washers, zinc (zamak,mazak) metal parts, brass & ms, ss, zinc, aluminium
Services: Manufacturer & exporter
Granite
Supplier: Soda ash light / dense 99.2%
sodium bicarbonate
caustic soda flakes 99%
sodium sulphate anhydrous (ssa) 99%
sodium sulphite flakes (ssf) 60%
sodium metabisulphate
hydrogen peroxide (h2o2) 50%
formic acid 85%
glacial acetic acid
paraffin wax
liquid paraffin (white oil) lp 100
menthol crystal
fumed silica
deg (di ethylene glycol)
mono ethylene glycol (meg)
poly ethylene glycol (peg),
base oil 150n, bs 150, 600n
bitumen 60/70
rpo (rubber process oil)
lioh (lithium hydroxide)
hco (hydrogenated castor oil)
12 hsa (hydroxy stearic acid)
ferrous sulphate heptahydrate
additive for lubricating oil
aromatic chemicals
Services: Exporting of chemicals & other products
REMELTED ZINC BLOCK ZINC 99.92%, ALU 0.002% , PB 0.003%, CD 0.002%, FE 0.003%
