Single Row Tapered Roller Bearing 32940 Inner Ring: 200.000mm Outer Ring: 280.000mm Width: 51.000mm Width of Inner Ring: 51.000mm Width of Outer Ring: 39.000mm Chamfer of Inner Ring: 3mm Chamfer of Outer Ring: 2.5mm Basic Dynamic Load Rating: 460KN Basic Static Load Rating: 950KN Limited Speed (rpm): 950(grease)/1300(oil) Gross Weight: 9.5kg Tapered roller bearings have tapered inner and outer ring raceways between which tapered rollers are arranged, optimizing rolling conditions. Tapered roller bearings are utilized in applications where there is a combination of radial and axial (thrust) loads. Tapered roller bearings are separable and have the following components: outer ring, inner ring, and roller assembly (containing the rollers and a cage). The non-separable inner ring and roller assembly is called the "cone", and the outer ring is called the "cup". Internal clearance is established during mounting by the axial position of the cone relative to the cup. It is important to note that tapered roller bearings are predominantly sold as individual components. Therefore, it is important to know the part number of both the cup and the cone, as they will most often differ and there are often many cup/ cone combinations available. While feasible to replace only the cup or the cone when replacing a tapered roller bearing, it is not recommended as it greatly decreases bearing life. Tapered roller bearings are used in numerous applications and are capable of high loads and speeds. The predominant use is in any wheel application, where the tapered roller bearings are normally arranged in back to back pairs where they support axial and radial loads in both directions. Tapered roller bearings are available in a wide array of both inch and metric sizes.
Part number Jp12049/jp12010 Hm124646-ass90085 Hm127446-ass90093 Hm129848/hm 129814 Hm133444-90107 Jp14049/10 161400/ee161850 L163149-90051 L183448/10 L183449/10 Hh221430/221410 Hh221442/hh221410 Hh221449/hh221410 Hh224340/224310 M224748/m224710 Ll225749/ll225710 L225810 / l 225849 Hh228340/310 Hh228349/hh228310 Hm231132/hm231110 Hm231149 90096 M231649/10 Hh234048/hh234010 M236849/m236810 Hm237545/10 H238148/h238110 M238849/m238810 Hm231149/hm231110 M236845/m236810 H239640/h239610 Lm241149/lm241110 M241547/10 242649/242610 M244249/10 Ll244549/ll244510
Single row tapered roller bearings are able to harness both radial and axial forces. The axial load capacity depends on the degree of the contact angle. These parts are able to control the axial load in one direction only and that is wht they are assembled in pairs. The axial clearance or preload designated in these pairs of bearings is to be adjusted during assembly. The amount of the axial clearance or preload is determined according to the following criteria: operating conditions, the size and type of the roller beaings, and the specific requirements of the mating arrangements rigidity.
Single row tapered roller bearings are designed to carry combined loads, i.e. radial and axial loads acting simultaneously. The projection lines of the raceways intersect at a common point on the bearing axis to provide true rolling action and therefore have low frictional torque during operation. The axial load carrying capacity of a tapered roller bearing increases with increasing contact angle ±. The size of the contact angle, usually between 10 and 30, is related to the calculated coefficient e: the higher the value of e, the higher the contact angle.
Single Row Tapered Roller Bearing 30226 Inner Ring: 130.000mm Outer Ring: 230.000mm Width: 43.750mm Width of Inner Ring: 40.000mm Width of Outer Ring: 34.000mm Chamfer of Inner Ring: 4mm Chamfer of Outer Ring: 3mm Basic Dynamic Load Rating: 387KN Basic Static Load Rating: 539KN Limited Speed (rpm): 1620(grease)/2200(oil) Gross Weight: 7.02kg Single row tapered roller bearing can support a combined radial and axial load. If either a radial load or bi-directional axial load is to be carried, a pair of bearings must be used in a "face-to-face" or "back-to-back" mounting. The axial load carrying capacity of the bearings is largely determined by the contact angle. If the contact angle is larger, then the axial load carrying capacity is higher and vice versa. During equipment assembly, single row bearings can be set to the required clearance (endplay) or preload condition to optimize performance.
Single row tapered roller bearing Part no.: 30228 I.D: 140.000(mm) O.D: 250.000(mm) Width: 45.750(mm) Width of inner ring: 42.000(mm) Width of outer ring: 36.000(mm) Chamfer of cone: 4 Chamfer of cup: 3 Basic dynamic load rating: 439 kn Basic static load rating: 627kn Limited speed (rpm): 1512(grease)/2090(oil) Gross weight: 8.8kg
Part number Ee113091-113171d + entretoise xis 113089 Hm120848-90088(hm120848/hm120817dß) Hm124646-90056(hm124646/hm124618d) Hm127446-90048ß(hm127446/hm127415dß) Ee128111+ee128160cd+spacer x2s-128111bep 0.0200" Ee128160cd and one spacerx2s-128111ßß Hm129848/hm129814d Na130902/131401d Ee134102/134144d Ee161400/161901cd 161400d/161901/161901cd/x1s-161400 161901cd or dß/ßee161300ßßßßß L163149/l163110d xe spacer L163149/l163110cd L163110cd/l163149 Ee170950/171451cd Ee192150/192201d Hh221449/hh221410d Hh224346na/hh224310d M224749/710d Hm231149/11cd M231649d902a9ßßß M231649d assy 902a7 Hm237535510cd Hm237545na/510cd Hm237546d/hm237510 H239640/h239612cd H239649/239612cd Lm241149nw/lm241110d Normal industrial packing
Botanical Name: Piper nigrum Plant Family: Piperaceae Country of Origin: India Plant Part: White Peppercorns Growth Method: Wild Harvest Extraction Method: Steam Distillation Color: Clear Consistency: Thin Strength of Aroma: Medium Pepper is a perennial vine of the Piperaceae family indigenous to the Malbar coast of India. It is now cultivated in most tropical parts of the world. Pepper bears clusters of small flowers and small spherical fruits that turn red when they ripen. The berry-like fruits eventually become the peppercorns, and each one bears a single seed. The hot spice of White Pepper is made from its berries. It is the fully mature fruits from which the soft, fleshy outer layers had been ground off before drying. The berries of the pepper plant are called peppercorns and these plants are native to southern Asia. This plant was the main spice the European explorers were looking for when they discovered the New World. It still accounts for one fourth of the spice trade in the world. Did you know that white and black pepper come from the same plant? The white variety is allowed to fully ripen on the vine, as opposed to the black peppercorns, which is why it costs a bit more. The skins are peeled off and the inside of the peppercorn is white. White peppercorns have an earthy flavor whereas black peppercorns simply give heat to a dish. The white ones are popular in Mexican, Indian, and Asian dishes, perhaps because a lot of these recipes are spicy and earthy already and the white pepper complements the overall flavor of the dish. If you want to use white pepper, it is best to buy whole peppercorns because the flavor is longer lasting. Peppercorns start to lose their potency when you grind them, which is why freshly ground pepper is usually recommended.
No.: nu6/241.3m Old no.£º32948h Dimension£¨mm£©£º241.3¡á374.65¡á127 Basic£¨kn£©£ºc, 1260£¬co, 2660 Mass£¨kg£©£º56.2.
Product Name Tapered Roller bearing 351076 Structure Roller Bearing Bore Size 380 mm Outside Diameter 560 mm Width 82 mm Material GCR 15, Stainless steel etc. Cage GCR 15, Stainless steel etc. Weight 137kgs Number of Row Doble
Fly Ash: Fly Ash is by product generated during combustion of coal, and comprises the fine particles that rise with the flue gases. Ash which is collected from the bottom is termed bottom ash. Fly ash is collected by electrostatic precipitators or other particle filtration equipment before the flue gases reach the chimneys of coal-fired power plants and together with bottom ash removed from the bottom of the furnace is in this case jointly known as coal ash. Depending upon the type of coal being used, the specification of Fly Ash varies considerably, but Fly Ash contains substantial amounts of silicon dioxide and calcium oxide (CaO), both being endemic ingredients in many coal-bearing rock strata. We are a reputed Fly Ash Exporter based in India and are supplying Fly Ash different cement, ready mix concrete, steel, refractories and construction industries. The Major Utilization Areas Of Fly Ash : - Manufacture of Portland Pozzolanic Cement & Performance improver in Ordinary Portland cement (OPC). - Part replacement of OPC in cement concrete. - High volume Fly Ash concrete. - Roller Compacted Concrete used for dam & pavement construction. - Manufacture of ash bricks and other building products. - Construction of road embankments, structural fills, low lying area development. - As a soil amender in agriculture and wasteland development. Types of Fly Ash: - According to the type of coal used fly is classified into two types. Anthracite and bituminous coal produces Fly Ash classified as class F. Class C Fly Ash is produced by burning lignite or sub-bituminous coal. Class C Fly Ash has self-cementing properties. - Class F and Class C Fly Ash are products of the combustion of coal in large power plants. Fly Ash is collected in electrostatic precipitators or baghouses, and then transferred to large silos for shipment. When needed, Fly Ash is classified by precise particle size requirements, thus assuring a uniform, quality product. - Class F Fly Ash is available in the largest quantities. Class F is generally low in lime, usually under 15 percent, and contains a greater combination of silica, alumina and iron (greater than 70 percent) than Class C Fly Ash. - Class C Fly Ash normally comes from coals which may produce an ash with higher lime content generally more than 15 percent often as high as 30 percent. Elevated CaO may give Class C unique self-hardening characteristics. Minimum Order Quantity : 1 container
Four Row Tapered Roller Bearing 382968 Inner Ring: 340.00mm Outer Ring: 460.00mm Width: 310.00mm Chamfe: 4mm Basic Dynamic Load Rating: 2100KN Basic Static Load Rating: 8140KN Limited Speed (rpm): 367(grease)/482(oil) Gross Weight: 147kg The performance of four row tapered roller bearings or multi row tapered roller bearing are almost the same as double row tapered roller bearings, but their radial and axial loading capacity are much higher, can carry heavy axial loads in two directions. However, the limiting speed of four-row tapered roller bearing is lower. Usually used as rolling mill bearings, mainly used by heavy engine machines, such as, in a rolling mill, mining, metallurgy, plastics machinery, large cold and other heavy machinery. CJB can provide customers other tapered roller bearings with special structures, such as sealed tapered roller bearings, etc. 382930: 150mm*210mm*mm*165mm 382034: 170mm*260mm*230mm 382044: 220mm*340mm*305mm 382048: 240mm*360mm*310mm E625948: 240mm*338mm*248mm 38295: 260mm*360mm*265mm 382052: 260mm*400mm*245mm 381156: 280mm*460mm*324mm 382960: 300mm*420mm*300mm 382060: 300mm*460mm*390mm 381130: 300mm*500mm*370mm 382064X2: 320mm*480mm*380mm 382968: 340mm*460mm*310mm 381068: 340mm*520mm*325mm 381168: 340mm*560mm*425mm 381072: 360mm*540mm*325mm 381172: 360mm*600mm*420mm 381176: 380mm*620mm*420mm 381080: 400mm*600mm*356mm 381184: 420mm*700mm*480mm 381088: 440mm*650mm*376mm 381992: 460mm*620mm*310mm 381092: 460mm*680mm*410mm 381996: 480mm*650mm*338mm 381096: 480mm*700mm*420mm 3810/500: 500mm*720mm*420mm 3810/530: 530mm*780mm*450mm 3819/560: 560mm*750mm*368mm 3811/560: 560mm*920mm*620mm 3819/600: 600mm*800mm*380mm 3810/600: 600mm*870mm*480mm 3811/800: 600mm*980mm*650mm 3819/630: 630mm*850mm*418mm 3810/630: 630mm*920mm*515mm 3811/630: 630mm*1030mm*670mm 3819/670: 670mm*900mm*412mm
Conveyor rollers, carrying rollers, return rollers, conveyor idlers, belt conveyor roller, smsr gearbox, belt conveyor pulley, v belt pulley, conveyor roller bearing housing, conveyor belt, stone crusher parts, ci casting, casting parts, sg castings, die casting.
No.: NNAL6/222.25-1Q4/C9W33XYA2 Old No.:154744QU Dimension(MM):222.25 D-298.45 B-225.425 Basic load(KN):C,1580 Co,4640 Mass(KG):45.2.
Jaipur Bearings Limited founded in 1991 is a modern enterprise specialized in the production of precision bearings. Our company in partnership with Shandong Bearing Company, which was founded in 2012 owns automatic production lines. 30202 - 30240 32203 - 32236 32304 - 32340 32004 - 32020
Egg white and yolk separator machine 1000pcs/hour for single row , 2000-4000pcs/hour for 2-row ,big capacity egg yolk and white production line by customized ,welcome order!
China Tapered Roller Bearing , Metric Taper Roller Bearing, Tapered Bearing, provided Wuhan Honghao Machinery Co., Ltd1. Material: Chrome steel2. Type:A. Metric size as 30200 series, 30300 series, 32300 series, 32000 series, 31300 series, 33000 series, 33200 series, 32200 series, 33100 series etc.B. Inch-size as LM11749/LM11710, LM11949/LM11910, 39581/39520, 6386/6320, 5BC, 11BC, 09067/09195, LM102949/LM102910, LM104949/LM104911, M12649/M12610, LM12748/LM12710, LM12749/LM12710, LM29749/LM29710, LM300849/LM300811, L44649/L44610, HM218248/HM218210, L45449/L45410, LM48548/LM48510, LM501349/LM501310, LM67048/LM67010, etc.3. Grade: P0, P5,4. Notes: Tapered roller bearings with radial oriented mainly to bear radial and axial joint load. Bearing load capacity depends on the angle of the outer ring raceway, the greater the angle the greater the carrying capacity. This kind of bearing is separable bearings, rolling bearings according to the number of rows into single row, double row and four row tapered roller bearings. Single row tapered roller bearing clearance adjustment required to the user during installation; Double row and four row tapered roller bearing clearance from the factory has been given based on user requirements, users do not need to adjust.Tapered roller bearings have tapered inner and outer ring raceways, tapered roller arranged between the two. The surface of the projection lines of all cone bearing axis in the same point together. This design makes tapered roller bearings particularly suitable for bearing complex (radial and axial) loads. Most of the axial load bearing capacity is determined by the contact angle �± ; A angle increases, the higher the axial load capacity. Angle size of the computational coefficient e to represent; E greater the contact angle the greater the bearing axial load greater applicability.Tapered roller bearings are usually separated type, that is, with roller and cage assembly of the inner components of the composition of the inner cone with tapered outer (outer) installed separately.5. Application: Tapered roller bearings are widely used in automotive, mill, mine, metallurgy, plastics and machinery.6. Packing: Single colour boxes or industrial packing, carton around 22kg, then into wooden or steel pallet.
We are manufacturer of all types of tapered roller bearing. The given part numbers 30204 (br-30204) / 320/32x (br-320/32) / 30205 / u399-u360l / etc of the tapered roller bearing are suitable for tata ace. We also accept the drawing of the customer and according to that drawing, we developed their product.
Product Specification The inner and outer ring raceways are segments of cones and the rollers are also made with a taper so that the conical surfaces of the raceways and the roller axes if projected, would all meet at a common point on the main axis of the bearing.> This conical geometry is used as it gives a larger contact patch, which permits greater loads to be carried than with spherical (ball) bearings, while the geometry means that the tangential speeds of the surfaces of each of the rollers are the same as their raceways along the whole length of the contact patch and no differential scrubbing occurs. When a roller slides rather than rolls, it can generate wear at the roller-to-race interface, i.e. the differences in surface speeds creates a scrubbing action. Wear will degenerate the close tolerances normally held in the bearing and can lead to other problems. Much closer to pure rolling can be achieved in a tapered roller bearing and this avoids rapid wear. The rollers are guided by a flange on the inner ring. This stops the rollers from sliding out at high speed due to their momentum. The larger the half angles of these cones the larger the axial force that the bearing can sustain. Tapered roller bearings are separable and have the following components: outer ring, inner ring, and roller assembly (containing the rollers and a cage). The non-separable inner ring and roller assembly is called the cone, and the outer ring is called the cup. Internal clearance is established during mounting by the axial position of the cone relative to the cup.
Tapered roller bearings are separable and have the following components: outer ring, inner ring, and roller assembly (containing the rollers and a cage). The non-separable inner ring and roller assembly is called the cone, and the outer ring is called the cup. Internal clearance is established during mounting by the axial position of the cone relative to the cup.
