SH 100 is a thixotropic, fiber-reinforced, structural cement mortar for protecting and repairing concrete structures. Its physical and mechanical properties allow to correct large irregularities in the substrate with a rapid intervention. The product can be used for repairing reinforced concrete structures such as front panels of balconies, beams, columns, stringcourses, moulding, cornices and fair faced concrete surfaces. It is easily applied using a continuous plastering machine and is suitable for large surfaces such as drainage channels, dams, bridges, water pipes, tanks, containment structures made of reinforced concrete.
Ferrous & non ferrous scraps such as rail scrap, copper scrap, aluminium scrap, new ferrous & non ferrous products such as copper cathode, aluminium ingots, oil spill bioremediation & absorption products from cotton lint and polymer based soil stabilization product (2kg to treat 50m3 soil)..
polymer
Product name: pestle and mortar Origin: Vietnam Made from coconut wood MOQ: 500 sets Packing: in bulk or carton
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Polymer..Trade.
SH 300 will form a high-strength abrasion and chemical resistant, self-leveling mortar. Because it is based on Portland cement and latex polymers, and does not depend on gypsum, it may be used indoors or outdoors. SH 300 flows out to produce a smooth resurfacing or leveling compound for structurally sound existing slabs.
SH 400 is a high-performance, fast-setting, multipurpose repair material. Durable in wet environments, SH 400 is a blend of Fast-Setting hydraulic cement and quality aggregates. SH 400 is non-metallic, and no chlorides are added. SH 400 with water to produce a workable, high quality mortar material that is ideal where fast strength gain, high durability and low shrinkage are desired. SH 400 sets in 15 minutes and achieves structural strength in 1 hour.
SH 500 is a high-performance, polymer modified, cement coating. Durable in multiple environments, SH 500 is a blend of Rapid Set hydraulic cement, high performance additives and quality aggregates. SH 500 has a working time of 30 minutes, can be exposed to hydrostatic pressure in 3-5 days, and cures to a concrete gray color.
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
K18 Hair Care Leave-in Molecular Repair Hair Mask 15ml
Eva foam sheets, expansion joint filler boards, xlpe foam sheets.
Technical Data Sheet Of Accoset-50 ALUMINA MORTAR (Test Certificate) General Properties A. Max service temperature - 1500 oC B. Maximum grain size - 0 - 1.5 mm C. Water required for mixing - 22 - 30% D. Setting - Airsetting E. Sintering Temp - 1550 oC Chemical Properties A. Al2O3 - 50.00% B. SiO2 - 31.00% c. Fe2O3 - 5.00% D. LOI - 7.00% Physical Properties A. Dry Density - kg / m3 B. CCS - 17 kg / cm2 after drying at 110C / 24 hr C. MOR - 20 kg / cm2 at 110 oC/ 24 hr 18 kg/cm2 at 800 C/ 3 hr Thermal Properties - A. Refractoriness ( Orton / C) - 31.5 orton cone/1699 oC Packaging - 25 - 50 kg bags Storage Life - 12 months Delivery State - Dry
Refractory Mortar are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer two types of refractory mortar according to its application including Heat setting mortar : IS-6 Mortar, IS-8 Mortar, 40% To 90% Mortar Air setting Mortar : Set-50 Mortar, Set 50F Mortar
Marketing of products such as thermal coal, coke, clinker, cement in bulk and packaged, aggregates, polymers for road paving and natural organic material for absorption of hydrocarbons, acids, spilled biological material. boat, barge brokerage service. sale of spare parts for port equipment, empty stackers, reach stackers, fork lift, terminal tractors, rtg and rmg cranes, ship to shore cranes, any spare part or machine only with part number, any spare part or equipment for the hydrogen and oil and gas industry, lightings systems, fire fighting system..
Polymer raw materials, commodities, frozen tuna fish, frozen shrimps.
Special cement, polymer repaired mortar, carbon masterbatch rubber, nylon chip, building tool, construction materials..
EPEM is used as the base polymer. The main properties of EPDM are its outstanding heat, ozone, and weather resistance. so that the most common use is in vehicles as used in door seals, window seals, trunk seals. Application: Weather Strips, Radiator Hoses, Heater Hoses, Protectors(Solid, Sponge), Brake System, Grommet
NBR is a synthetic rubber copolymer of acrylonitrile (ACN) and butadiene. Although its physical and chemical properties vary depending on the polymer's composition of nitrile, this form of synthetic rubber is unusual in being generally resistant to oil, fuel, and other chemicals. It is used in the automotive industry to make fuel and oil handling hoses, seals and grommets. Application : Air Intake Hose, Safety shoes, High-pressure Hose, Packing, Roller, Belt, O-ring
This is a rubber adding Chlorine instead of methyl to the structural formula of natural rubber, which has the same elasticity as NR, relatively superb heat-resistance, oil-resistance, and weather-resistance compared to NR and SBR, which are the general-purpose rubbers, and similar ozone-resistance as NBR. The use for this rubber is for CVJ-boots, dust covers, and hoses. Application: Wire Cover, Conveyor Belt, Mounting Rubber, Tank or CAn Lining, Anti-corrosive Packing, Anti-corrosive Roll, Dust Cover
