SH 500 is a high-performance, polymer modified, cement coating. Durable in multiple environments, SH 500 is a blend of Rapid Set hydraulic cement, high performance additives and quality aggregates.
SH 500 has a working time of 30 minutes, can be exposed to hydrostatic pressure in 3-5 days, and cures to a concrete gray color.
Acid Resistance Mortar are used for Lining of Acid Resistance Bricks which are chemically resistant and thermally durable. These are used for masonry construction and flooring which is prone to chemical attack. Types of Acid Resistance Mortar: Silicate Mortar Resin Mortar Sulphur Mortar
Supplier: Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,
Polyethylene(PVC) geomembrane, as a high-performance waterproof and impermeable material, has many remarkable advantages. Thickness: 0.1mm-3mm Width: 2m-6m Color: Black/White/Other colors Following is our PVC geomembrane Thickness 1.6mm specifications: Tensile Strength (vertical and horizontal): 20MPa/mm Elongation at Break (vertical and horizontal): 580% Right-angle tearing strength (vertical and horizontal): 180N/mm Water vapor permeability coefficient: Using temperature range: +70~ -70 Puncture strength 360N Water impervious: 100% Root resistance: 100% Difference Between PVC Geomembrane and HDPE Geomembrane PVC geomembrane and HDPE geomembrane have significant differences in physical properties, treatment difficulty, joint treatment, puncture resistance, and resilience to deformation. Physical Properties and Suitable Environment: PVC membrane: relatively soft and easy to bend, suitable for general waterproofing projects, swimming pools, and wastewater treatment, etc. HDPE membrane: has higher strength and wear resistance, suitable for engineering projects with higher strength and durability requirements, such as water conservancy projects and landfills. Handling Difficulty: PVC membrane: Due to its flexibility, we can make seams in controlled factory conditions, typically requiring fewer on-site seams than HDPE geomembrane. HDPE membrane: Handling in cold weather conditions can be challenging and requires sewing outdoors. Puncture Resistance: PVC membrane: It is harder to penetrate than HDPE and has high elongation characteristics, allowing it to adapt to site changes without reinforcement. HDPE membrane: While it has elasticity, it becomes plastic after exceeding its yield point and no longer has elasticity. Deformation Recovery: PVC membrane: Most of the deformation can be recovered, with a high tensile elongation, suitable for engineering projects with larger design strain limits. HDPE membrane: Deformation after exceeding the yield point cannot be recovered, and the material properties will change. We should select the appropriate geomembrane according to the specific project requirements and the use environment. HDPE geomembrane is suitable for projects that require high strength and durability, while PVC geomembrane is suitable for general waterproofing projects and water treatment.
PE Tarpaulin agricultural shielding waterproof cloth WP018 PE Tarpaulin Features: waterproof sunscreen, cold resistance, aging resistance, windproof snow anti-freezing, soft and easy to fold. Scope of application: Its usage is widely, mainly in truck cover, farm fence, awning waterproof cloth, agricultural shielding, householdtent mat cloth, fish pond and shrimp pond impermeable cloth, pet cage waterproof roof, chicken roll sheep pen duck shelter shade insulation breeding tarpaulin. Gram Weight: 50g 100g 120g 140g 160g 180g 200g 300g Our PE Tarpaulin advantages: Excellent waterproof performance : After special treatment, has excellent waterproof performance, can effectively prevent water penetration Good cold resistance : polyethylene material has good low temperature resistance, making PE waterproof cloth can still maintain good flexibility and strength in the cold environment . Strong wear resistance : PE Tarpaulin after stretching and coating treatment, the surface is more smooth and wear-resistant, can resist external wear and friction Good corrosion resistance : It has excellent chemical corrosion resistance and can resist the erosion of a variety of chemical substances . â??Light and easy to carry : It is light weight, small size, easy to carry and store . Environmental protection and non-toxic â?? : it is odorless, feel like wax, clean and environmentally friendly . High elasticity : PE Tarpaulin has high elasticity, good tear strength and peel strength. Suitable for a variety of environment : suitable for high temperature and low temperature area, flame retardant performance up to NFPA701 standard, environmental protection and non-toxic, no heavy metals. Long service life : It has excellent antioxidant properties and anti-aging properties, long service life . Strong anti-pollution : different from traditional coating materials, PE waterproof cloth has excellent anti-pollution ability, keep clean A wide range of applications PE waterproof cloth is widely used in many fields, including the construction field (such as roofing, basement, tunnel, bridge and other projects waterproof treatment). The transportation field (such as roads, railways, airports and other infrastructure). As well the agricultural field (such as greenhouse coverage, field irrigation pipeline dressing). Warehousing logistics (such as goods cover, protection) and outdoor supplies (such as tents, poncho, etc.)
We supply the Required Grade and Type of Cement that have been procured from the Top Brands made available to the customers at the required Specification for the best prices in the Bulk quantities required. It is obvious that Cement is a very useful binding substance in construction. The usage of cement over diverse fields of construction has made it a very significant civil engineering material. Cement mixed with water and fine aggregate produces mortar, sand and gravel to create concrete. It is the most-consumed resource and is widely available in the market.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.
