Features 1) Good weather fastness and dimensional stability. 2) Excellent performance to high and low temperature (-40â?? ï½? +80â??), UV resistant and anti-corrosion. 3) Higher tensile strength and better extensibility under normal construction conditions. 4) Easy installation, solid joint, and no environmental pollution. 5) Good rooting penetration resistance. Application 1) Roofs, basement, toilet, bridge, underground, tunnel and dam. 2) Industrial and civil building waterproof. 3) Geo-synthetic liner for swimming pool, channels, irrigation system. 4) Especially for projects with high requirements in durability, anti-corrosion and deformation.
HDPE geomembrane Application 1.Landfill(primary &secondary containment) 2.Landfill caps/closures 3.Lagoon Liners 4.Mining Heap Leach Pads 5.Pond Liners 6.Canal Linings 7.Raw Water treatment reservoirs 8.Potable water reservoirs 9.Retention ponds Application: Environmental protection and environmental sanitation (for example, living landfill yard, sewage treatment plant, power plant adjusting tank, industrial and hospital solid waste, etc.) We have good quality ASTM standard HDPE geomembrane ,for more details
HDPE pre-applied waterproof membrane is made of three layers of materials which are HDPE sheet, hot-melt pressure sensitive adhesive, and isolating material respectively. And the isolating material can be special sand(type S) and isolation membrane(type M) Thickness 1.2mm 1.5mm or as required . Width : 2m or as required Length :20m or as required . Product Properties : 1.Pre-applied full-bonding installation: the HDPE pre-applied membrane sanding surface up temporary fixed on the bottom cushion. Direct binding reinforcement, and then poured concrete. The membrane coated sand layer will combine with it tightly ,no water moving between layers. 2.It has strong self-healing ability and can repair slight construction injury. 3.High strength of elongation, strong breaking tensile strength and good anti-perforation performance . 4..With strong chemical resistance to acid and alkali 5.Integration of self adhesion, waterproof and protection, so that can reduce construction links 6.Wet method construction, no need flat layer, low requirement for the base, not affected by weather and base moisture, it has obvious advantage of constructions in rainy season. 7.The floor board of the building should be constructed with a pre-applied anti-sticking method. This method no need protective layer. 8. one layer can reach level one waterproofing security requirements . Product Application Waterproof and anti-seepage , caverns , tunnels , subway , bridge , water conservancy , dam , basement , landfill , sewage treatment pool ,municipal construction we are qualified direct manufacture withs ISO certificates
Products Properties : 1. high tensile strength, large ductility, strong applicability for contraction or deformation of the substrate. 2.large width of material, high construction efficiency, small product consumption 3.Good diffusivity of water vapor, easy discharge of condensate, easy discharge of moisture left in the substrate 4.Root penetration resistance, chemical corrosion resistance and aging resistance 5. good flexibility at low temperature even at -30â?? and heat resistance 6.No liquid flow at high temperature 7. Cold construction and good safety performance. Size & Specification Size: 2m (width)*20m (length) Thickness: 1.2mm; 1.5mm; 2.0mm Type: Homogeneous, Reinforced, Fabric back,also we can make self adhesive style Exposed and Non-exposed Color: white, Grey or customized Certificate: ISO9001/14001, Root Resistance Certificate Product Application Widely used for waterproof and anti-seepage, caverns, tunnels, subway, bridge, water conservancy dam basement, landfills, sewage treatment pool, municipal construction
Products Properties : 1.With excellent ageing-resistant performance, it will not become brittle due to transfer of plasticizer 2.No plasticiser,do not release toxic gases during welding .Environmentally-sound, chloride-free and no pollution 3.High breaking strength and tear strength, anti-impact and perforation resistance 4.Good flexibility at low temperature, and no bending and crack at -40â?? 5. Good root resistance 6. FM certificate approved. 7. Good resistance to chemical attack; resistance to the corrosion of acid, alkali, salt, animal and vegetable oil , and resistance to alga, microbial growth. 8.white color, smooth surface, high reflectance, better energy saving effect. Specification &Classification Size: 2m (width)*20m (length) Thickness: 1.2mm; 1.5mm; 2.0mm Type: Homogeneous, Reinforced, fleece back,also we can make self adhesive style Color: white, Grey or customized Certificate: ISO9001/14001,FM Certificate , Root Resistance Certificate Product Application Convention centers , exhibition halls ,stadiums , library , airport terminals , industrial plants,warehouse , logistics and other buildingâ??s metal roofs , exposed concrete roofs and green roofs.
Winder® FRP tubular membrane housings(pressure vessels) End Entry Design Available in 150 psi pressure rating Suitable to hold 1pc 8" membrane housing(20"/40"/60" Length) Specification Winder® FRP tubular membrane housings(pressure vessels) End Entry Design Available in 150 psi pressure rating Suitable to hold 1pc 8" membrane housing(20"/40"/60" Length) Key Features Operating Temp Range: -10°C ---49°C Test pressure: 1.5x Design Pressure Operating pH Range: 3 11 Cleaning pH Range: 2 12 (less than 30 minutes) Please operate in accordance with User Guide of the FRP tubular membrane housings(pressure vessels) Frp Precision Filter Housing ADVANTAGES Winder® FRP tubular membrane housings(pressure vessels) has advantages as follows: â?¢Mirror finish of inner wall surface â?¢Anti-corrosion, anti-oxidation & aging â?¢Uneasy to damage the membrane column element â?¢High compressive strength â?¢Excellent anti-pollution performance â?¢Easy to assemble, long service life SPECIFICATION Material Fiberglass and epoxy. Process Fiberglass winding Pressure Rate (Bar) 150PSI Available height 20", 40" 60" Operating temperature -7 °C49 °C. Color white or customized Certificate ASME, ISO9001, ISO14001 FRP pressure vessel APPLICATION Winder® FRP tubular membrane housings(pressure vessels) are widely used in water treatment systems as follows: Pre-treatment treatment of: Garbage, Hospitals, family planning centers Health & epidemic prevention station Industrial zone, incineration plant landfill leachate treatment plants Living& food waste treatment plants Waste water treatment produced by: Coking, oil, gas, coal, chemical Purification, desalination, recycling separation of mobile water Industrial water & wastewater applications for reclamation and reuse. Recovery of Acid, alkali & precious metals
Rohone® frp membrane housing pressure vessels End Entry Design Available in 450psi, 600psipressure rating Accommodates standard make 8" Membrane Element Specification Rohone® frp membrane housing pressure vessels 8 Inch End Entry frp filter housings Design Available in 450psi, 600psipressure rating Accommodates standard make 8" Membrane Element industrial frp membrane housings Key Features Operating Temp Range: -10°C ---49°C Test pressure Standard: 1.3x Design Pressure ASME: 1.1x Design Pressure Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 - 11 Cleaning pH Range: 2 - 12 (less than 30 minutes) Mirror inner wall and brightly surface. White color is as standard. Customized colors are also available. ASME Code stamp available upon request Please operate in accordance with User Guide
Winder® frp membrane housing pressure vessels 4" End Entry Design Available in 300 psi, 450Psi, 600Psi, 1000Psi, 1200Psi, pressure rating Accommodates standard make 4" Membrane Element Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Winder® frp membrane housing pressure vessels 4" End Entry Design Available in 300 psi, 450Psi, 600Psi, 1000Psi, 1200Psi, pressure rating Accommodates standard make 4" Membrane Element Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF 4 Inch End Entry frp pressure vessels Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 - 11 Cleaning pH Range: 2 - 12 (less than 30 minutes) Mirror inner wall and brightly surface. BSPP/NPT thread available White color is as standard. Customized colors are also available. ASME Code stamp available upon request
Polyaspartic Tiles Waterproofing Varnish DESCRIPTION PF600 is solvent free,two-component, hand applied, Polyaspartic clear coating. APPLICATION PF600 is used in kitchen, toilet and shower room waterproofing applications. FEATURES AND BENEFITS Fully bonded to the tile surface Low odor Excellent anti-slip property Cures fast,ready for use after 8-12 hours Convenient application Visible waterproofing
4 INCH frp membrane housings W40S300 Winder frp membrane housing pressure vessels 4" Side Entry Design Available in 300 psi, 450Psi, 600Psi, 1000Psi, 1200Psi, pressure rating Accommodates standard make 4" Membrane Element Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Winder frp membrane housing pressure vessels 4" Side Entry Design Available in 300 psi, 450Psi, 600Psi, 1000Psi, 1200Psi, pressure rating Accommodates standard make 4" Membrane Element Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 - 11 Cleaning pH Range: 2 - 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME Code stamp available upon request
FRP MEMBRANE HOUSINGS R80S300 - ALUMINIUM CAP Side Entry Design Available in 300-600 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) FRP MEMBRANE HOUSINGS Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ISO9001, ISO14001, UL/NSF Rohone aluminium cap frp membrane housing pressure vessels 8 INCH frp membrane housing price Side Entry Design Available in 300-600 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ISO9001, ISO14001, UL/NSF 8 INCH frp membrane housings Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88MPa) Operating pH Range: 3 11 Cleaning pH Range: 2 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME un-Coded economy series or saving ro systems cost
FRP MEMBRANE HOUSINGS W80S1800 Winder frp membrane housing pressure vessels Side Entry Design Available in 1800 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40 x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Winder frp membrane housing pressure vessels industrial frp membrane housings Side Entry Design Available in 1800 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40 x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF 8 INCH frp filter housings Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 - 11 Cleaning pH Range: 2 - 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME Code stamp available upon request
Winder frp membrane housing pressure vessels End Entry Design Available in 150psi, 300psi, 450psi, 600psi, 1000psi, 1200psi pressure rating Accommodates standard make 8" Membrane Element 8 Inch Side Entry frp filter housings Specification Winder frp membrane housing pressure vessels End Entry Design Available in 150psi, 300psi, 450psi, 600psi, 1000psi, 1200psi pressure rating Accommodates standard make 8" Membrane Element 8 Inch End Entry frp pressure vessels Key Features Operating Temp Range: -10°C ---49°C Test pressure Standard: 1.5x Design Pressure ASME: 1.1x Design Pressure Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 - 11 Cleaning pH Range: 2 - 12 (less than 30 minutes) Mirror inner wall and brightly surface. White color is as standard. Customized colors are also available. ASME Code stamp available upon request Please operate in accordance with User Guide 8 Inch End Entry frp filter housings Quality Assurance Hydro-static Leakage Test Pressure: Standard: 100% test, not sampling ? 100,000 times cycle test ? Burst test with 6 times of its operating pressure ? 100% QA test with 1.5x design hydraulic pressure. ASME: 1.1x Design Pressure ? 100% QA inspection and cleaning before final packaging and delivery to customers. ? Submitted for NSF standard 61 Applications: Winder FRP membrane housing pressure vessels are widely used for industrial waste water treatment, seawater desalination, brackish water desalination, RO system for electronics, electric power, food & beverage, metallurgy, chemical, pharmaceutical and other fields. frp filter housings Notice: Please operate in accordance with User Guide! All information is subject to change without prior notice. Please contact us for the latest product information and specifications.
FRP MEMBRANE HOUSINGS R80S450 Side Entry Design Available in 300-600 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Rohone aluminium cap frp membrane housing pressure vessels Side Entry Design Available in 300-600 psi pressure rating Accommodates standard make 8" Membrane Element frp membrane housings Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF 8 INCH frp membrane housings Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88MPa) Operating pH Range: 3 11 Cleaning pH Range: 2 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME un-Coded series for saving cost of ro systems. Quality Assurance Hydro-static Leakage Test Pressure: 8 INCH frp filter housings Standard: 100% test, not sampling ? 100,000 times cycle test ? Burst test with 4 times of its operating pressure ? 100% QA test with 1.3x design hydraulic pressure. ASME: 1.1x Design Pressure ? 100% QA inspection and cleaning before final packaging and delivery to customers. ? Submitted for NSF standard 61 8 INCH frp ro membrane housings Applications: Rohone FRP membrane housing pressure vessels are widely used for industrial waste water treatment, seawater desalination, brackish water desalination, RO system for electronics, electric power, food & beverage, metallurgy, chemical, pharmaceutical and other fields. 8 INCH frp membrane housing price Notice: Please operate in accordance with User Guide! All information is subject to change without prior notice. Please contact us for the latest product information and specifications.
Side Entry Design Available in 600 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Winder frp membrane housing pressure vessels Side Entry Design Available in 600 psi pressure rating 8 INCH frp membrane housings Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF 8 INCH frp membrane housings Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 11 Cleaning pH Range: 2 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME Code stamp available upon request
FRP MEMBRANE HOUSINGS W80S1200 8 INCH frp filter housings Side Entry Design Available in 1200 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON,BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Winder frp membrane housing pressure vessels Side Entry Design Available in 1200 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY, CSM, VONTRON,BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF 8 INCH frp membrane housings Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88 MPa) Operating pH Range: 3 11 Cleaning pH Range: 2 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME Code stamp available upon request Quality Assurance Hydro-static Leakage Test Pressure: Standard: 100% test, not sampling ? 100,000 times cycle test ? Burst test with 6 times of its operating pressure ? 100% QA test with 1.5x design hydraulic pressure.
FRP MEMBRANE HOUSINGS W80S1500 Winder frp membrane housing pressure vessels Side Entry Design Available in 1500 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY ,CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF Specification Winder frp membrane housing pressure vessels Side Entry Design Available in 1500 psi pressure rating Accommodates standard make 8" Membrane Element Element length: 40" x (1-8) Applicable to: DOW, HYDRANAUTICS, OSMONICS, KOCH, TORAY ,CSM, VONTRON, BDX, etc. Standard: ASME RP, CE, ISO9001, ISO14001, UL/NSF 8 INCH frp membrane housings Key Features: Operating Temp Range: -10°C ---49°C Internal permeate port not to exceed 125PSI(0.88MPa) Operating pH Range: 3 11 Cleaning pH Range: 2 12 (less than 30 minutes) Mirror inner wall and brightly surface. Multi-ports option White color is as standard. Customized colors are also available. ASME Code stamp available upon request 8 INCH frp membrane housing price Quality Assurance Hydro-static Leakage Test Pressure: Standard: 100% test, not sampling ? 100,000 times cycle test ? Burst test with 6 times of its operating pressure ? 100% QA test with 1.5x design hydraulic pressure. ASME: 1.1x Design Pressure ? 100% QA inspection and cleaning before final packaging and delivery to customers. ? Submitted for NSF standard 61 Applications: Winder FRP membrane housing pressure vessels are widely used for industrial waste water treatment, seawater desalination, brackish water desalination, RO system for electronics, electric power, food & beverage, metallurgy, chemical, pharmaceutical and other fields.
Made from PP(polypropylene) or PET(polyester) short fiber by non woven needle punched manufacturing process. Item: Short fiber needle punched non woven type. Description: Made from PP(polypropylene) or PET(polyester) short fiber by non woven needle punched manufacturing process, it has isolation, filtration, drainage, reinforcement, protection and maintenance etc. Function. Specification: 80g/m2-1500g/m2 1m-6m in roll width,the length as clients request Property: Good flexibility,resistant to corrosion,resistant to acids and alkalis,anti-oxidation Separation,filtration,drainage,reinforcement,protection,and maintenance function PP/PET Woven Geotextile Application: Water conservancy project and hydropower project Road paving,railway Airport and port River bank protection and tunnel Environmental protection etc. Our Folding Insect Screen and Aluminum Insect Screen, Fiberglass Mesh has been exported to multiple countries.
Thermoplastic polyolefin (TPO) rolls, which use advanced polymerization technology, combine the durability and weather resistance of ethylene - propylene (HP) rubber with the thermal weldability of polypropylene.The coil has long - term weather resistance and does not use plasticizer. Product Feature 1. Few auxiliary materials, convenient construction and good system integrity; 2. Excellent tensile, tear and puncture resistance; 3. No plasticizer, no plasticizer migration problem, excellent heat aging resistance and uv resistance, direct exposure, large thickness above the base, durable; 4. Hot air welding, high seam peeling strength (twice as high as PVC); 5. Fast welding speed; 6. Chlorine free and 100% recyclable, environmentally friendly; 7. Maintain excellent thermal welding performance for a long time, easy to repair; 8. Smooth surface, no fading, anti-pollution; Scope of application Widely used in industrial and civil and public buildings of all kinds of roofing waterproof works.
This kind of waterproof coiled material is made in the following way: base materials are firstly dipped into asphalt or thermoplastic elastomer (e.g. SBS), thermoplastics (e.g. APP or APAO) and modifiedasphalt; then both surfaces are coated with elastomer or plastic asphalt; fine sands and mineral grains (pieces) or polyethylene memb ranes are spread or covered on its upper surface; fine sands or polyethylene membranes are spread or covered on its lower surface. Product Feature * It has good waterproofing and ageing-resistance function; * Not flowing at highest temerature and no crack at lowest temperautre; * Easy application, no pullution; * Long service life; Matters need attention * no construction shall be allowed on rainy, snowy or windy days above grade 5; * construction site and personnel safety protection facilities are complete, fire fighting equipment is effective and placed according to regulations;
