Alkali-resistant fiberglass mesh fabric for reinforcing cement, slabs, plaster, etc. for exterior insulation finishing system (eifs), alkali-resistant fiberglass reinforcement mesh and mat combined mesh for waterproofing roofing system, fiberglass reinforcement mesh fabric for grc wallboard or laminate panels in architectural applications, fiberglass reinforcement mesh fabric for fire-resistant application, fiberglass self-adhesive mesh tape for drywall joint or repair, wall patch corner tape, glass-wool ceiling, fiberglass printing mat, Fiberglass decoration cloth, drywall sanding screen (abrasive open mesh), sanding sponge, fiberglass wall covering, fiberglass laminated bopp tape.
Square Mesh products in 6.0m x 2.4m sheet sizes are general-purpose ribbed mesh sheet used to reinforce concrete slabs. *SPECIFICATIONS* Material Carbon Steel Grade 500 Mpa Length 6000mm x 2400mm Main Wire (mm): 6.00@200, 6.75@200, 7.60@200, 8.60@200, 9.50@200, 7.60@100 mm *STANDARDS* Manufactured in accordance with AS/NZS 4671:2019 ACRS Certified NOTE - Can be manufactured in accordance with various international standards (EN, BS, ASTM and AS/NZS) *PACKAGING* Unit of Measure Sheets Pack Type Bundles FCL Quantity 25MT
Trench Mesh products in 6.0m x (200mm, 300mm, 400mm, and 500mm) sheet sizes and are a general-purpose ribbed mesh sheet used to reinforce concrete slabs with a narrow profile. *SPECIFICATIONS* Material Carbon Steel Grade 500 Mpa Length 6000mm x (200mm, 300mm, 400mm, or 500mm); width is dependent on number of wires (3,4, 5, or 6) Main Wire: 7.60@100, 10.70@100, 11.90@100 mm Cross Wire: 4.00@300, 4.75@300 mm *STANDARDS* Manufactured in accordance with AS/NZS 4671:2019 ACRS Certified NOTE - Can be manufactured in accordance with various international standards (EN, BS, ASTM and AS/NZS) *PACKAGING* Unit of Measure Sheets Pack Type Bundles FCL Quantity 25MT
1.This machine adopts synchronous control technique, both welding time and cent-control welding is supervised by ipc ( industrial computer and chassis). 2.It adopts modularization design, so it is easy to improve the machine's function and feacure. 3. The line wires are fed automatically and continously, so it saves much welding time to wait. Feeding position is accurate, the edges are regular and also could be adjustable. 4. There is a big hopper for cross wires, it could contain one ton wires, in this case, it saves much labor to add wires. 0v Overall dimention:20*5*2.3m Gwc-2500d (5-12 Wire diameter:5-12 Number of electrodes:24 Space of line wire:100-200 Space of cross wire:50-200 Welding speed:50 times /min Rated voltage:380v Width of mesh:2500mm Rated electrical power:12*125kva Overall dimention:20*5*2.3m Contace person :anny Website: www.Weldingmachine.Cn Tel:15803186013 Hebei jiaoyang wire mesh machine co., ltd. Website: www.Weldingmachine.Cn Post code:053600 The main welding machine is pocked by plastic and spare parts is parked by wooden box
Z248.5/248.6/348.5/Z348.6/Z442.5/Z442.6/Z558.5/Z558.6 Grids and reinforcing meshes Reinforcing meshes is manufactured compliance with Swiss Standard SIA 16211 S550. It is different sides wire in the whole sheet as K188/K335 in longitudinal direction. Itâ??s used widely on construction footing foundation,flooring slabs,foundation beams,bridge and piers and tunnel of coal,mine,subway,and trian reinforced and support. Heyou wire mesh is a professional manufacturer for reinforcing meshes which can comply to Chinese standard ,Australian/New Zealand standard,Germany Standard, Normes Francaises,Swiss Standard, Osterreichische Norm etc. Our factory was approvaled by ISO.All the reinforcing meshes are follow to international standard.We have enough exporting experiences.Our salesman are more than 10years working experience in this fields. Our workers which has strong and skillfull are expert, they produce the reinforcing meshes better than tyro. They made reinforcing meshes has firmly welding spot,accurate wire diameter,mesh space and panel size,clearly ribbed,non rusted. The specification of reinforcing meshes conformance with Swiss Standard SIA 16211 S550 mesh type Pitch of wires(mm) diameter of wire(mm) Per meter area sqm/m Dimension of Mesh Area of Mesh(sqmm) Mass (kg/sqm) Weight of Mesh(kg) pL pC dL dC long cross L(mm) B(mm) K188 6 6 150 150 188 188 5000 2000 10 3.091 30.192 K335 8 8 150 150 335 335 5000 2000 10 5.372 53.72 Z248.5 6/4.5 7 150 150 248 257 5000 2000 10 3.422 34.22 Z248.6 6/4.5 7 150 150 248 257 6000 2000 12 3.472 41.668 Z348.5 7/5.5 8 150 150 348 335 5000 2000 10 4.628 46.28 Z348.6 7/5.5 8 150 150 348 335 6000 2000 12 4.694 56.326 Z442.5 8.0/6.0 9 150 150 442 424 5000 2000 10 5.857 58.57 Z442.6 8.0/6.0 9 150 150 442 424 6000 2000 12 5.94 71.282 Z558.5 8.5/7.5 10 150 150 558 524 5000 2000 10 7.315 73.15 Z558.6 8.5/7.5 10 150 150 558 524 6000 2000 12 7.418 89.014
Reinforcement steel mesh was welded by automatic electrical resistance welding machines conformance to standard AS-NZS 4761-2001. The material of reinforcement steel mesh is 250N, 500N, 500L, 300E, 500E. Reinforcement steel mesh is very poupular in civil engineering and construction. It always used on road subgrade, building foundation, tunnel support and reinforced,mine and coal reinforced and support, bridge construction etc. During construction works, It is not only increase our working speed and time but also save 75% construction cost and enhance the crack resistance. The specification of rectangular reinforcement steel mesh as below: Rectangular Reinforcing Mesh 2.4m*6m=14.4sqm Code Cross wire Longwire mm Mass/sheetkg Quantityin pack Pitch@mm No. x dia., mm Pitch@mm No. x dia., mm RL718 7.60 @ 200 30 x7.6 6.75 @ 100 25 x 7.6 68 20 RL818 7.60 @ 200 30 x7.6 7.60 @ 100 25 x7.6 79 20 RL918 7.60 @ 200 30 x7.6 8.55 @ 100 25 x 8.55 93 20 RL1018 7.60 @ 200 30 x7.6 9.50 @ 100 25 x9.5 109 15 RL1118 7.60 @ 200 30 x7.6 10.65 @ 100 25 x10.65 131 15 RL1218 7.60 @ 200 30 x7.6 11.90 @ 100 25 x11.9 157 10 The panel size 2.4m*6m is very pouplar in Australian market,but considered the transportation in container by sea and saved cost, we advise the customers to change the panel size to be 2.2m x5.8m.
Construction reinforcement mesh was made by plain steel wire. It main used on building construction complied with standard AS NZS 4671-2001. The material is 250N, 500N, 500L, 300E, 500E, the mesh size is 150x150mm, wire diameter is 5.3mm and 4.0mm and the overhang length is in both sides. These specificate is very pouplar in New Zealand civil engineering field. More features of construction reinforcement mesh and ours as below: 1. high quality raw material 2. electric resistance welding machine made it which has firmly solder join, size precision,and appearance good-looking 3. Professional management team 4. Complete QC rules and regulations 5. A full of laboratory testing instruments Advantage of construction reinforcement mesh by AS-NZS 4671-2001 standard: 1. Save 30% of steel bar dosages 2. Reduce 50%-70% work time, improve construction progress and shorten construction period. 3. Cut down 5%-10% construction cost 4. Used widely,it has a good market development prospects. The specification of construction reinforcement mesh by AS-NZS 4671-2001 standard as below: concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m structural SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm. the steel bar after drawing shape as below figure: 1. The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45. The angle scope is greater than 45 and is less than 70, the rib height is from 0.025d to 0.10d. 2. The reinforcing mesh panel includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost. Steel pallet for reinforcing mesh size 2.4m *6m Loading container for reinforcing mesh sheet: 2.4m *6m 3.Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of reinforcing mesh panel has single bars, twin bars or combination of single bars and twin bars. 4.The technical data of reinforcing mesh panle is contained composition and characteristic mechanical porperties of reinforcing steels. Notes: 1. Grade 250N is supplied as plain round reinforcing steel complying with AS 3679. 1, exceptthe tolerance of the diameter and roundness dosen't apply it. 2. For 500L steel bars, only requriement for wire diameter is less than 5.0mm is RekL 500 Material certificate of reinforcing mesh as below: Common size of Squre reinforcing mesh panel for Austialian Market Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6 x2.4 m sheets Cross-sectional area/m width No. x dia., mm Pitch@mm No. x dia., mm Pitch@mm Unit area kg/sqm Sheet, kg Long'l bars sqmm/m Cross bars sqmm/m Squre, with edge side-lapping bars SL102 10 x 9.5 + 4 x 6.75 200100 30 x 9.5 200 5.6 80 354 354 SL92 10 X 8.6 + 4 X 6.0 200100 30 x 8.6 200 4.6 66 290 290 SL82 10 x 7.6 + 4 x 6.0 200100 30 x 7.6 200 3.6 52 227 227 SL72 10 x 6.75 + 4 x 5.0 200100 30 x 6.75 200 2.8 41 179 179 SL62 10 x 6.0 + 4 x 5.0 200100 30 x 6.0 200 2.2 33 141 141 Squre, without edge side - lapping bars SL81 25 X 7.6 100 60 x 7.6 100 7.1 105 454 454 How can we conctrol our products quality for exporting Autralia? Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechanical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3. Secondly, the panel size tolerances measure way as: a. Panel Size dimensions 6m in length, there is 40mm tolerances. b. Panel size dimensions 6m in length, the tolerance is �±0.7% c. Wire diameter and mesh size measure and weld shear resistance test conformance to AS NZS 4761-2001 and as per contract. d. Weigh the each bundle weight to calculate each panel weight.
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
Steel Reinforcing Mesh Roll is used to provide tensile strength and crack control to structural concrete elements. Steel reinforcing mesh is the thin ribbed wire that can be make rolls presentation. Advantages to save more than 33% of steel, reducing costs 10% -30%; increase the speed of construction can shorten the duration of about 80%; to improve the quality of engineering structures, and concrete bonding anchoring reliable, smooth reinforcement bond strength equal to three times more, and the overall good, deviation is small, anti - cracking performance above 75%. Application Retaining and shear walls Beams and columns Concrete paving overlays Precast concrete elements Suspended floor slabs Swimming pool and gunite construction size(mm) 2.8-5.3 Reinforcement spacing(mm) Longitudinal wire 50-200mm Cross wire 30-1000mm Sheet size Length 2-50m Width 1-1.3m Mechanical and process property Meet GB/T1499.3-2002 standard;AS/NZS 4671; 2001,BS 4483:2005,A185-02
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
Reinforcing Trench Mesh made from CRB550(550MPa) ribbed wires. The reinforcing trench mesh products all come 6.0m longs, available in 3-Bar, 4-Bar, 5-Bar and 6-Bar, as well as 8, 11 and 12mm wires. Its long, narrow sheets of concrete reinforcing mesh, has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction. Used specifically for residential footing trenches, paths or other narrow spaces. Length m Width m Longitudinal Wires mm Cross Wires mm Mass Kg 6.0 0.2 7.6 @ 100 4.77 @ 300 7 6.0 0.3 7.6 @ 100 4.77 @ 300 9 6.0 0.4 7.6 @ 100 4.77 @ 300 12 6.0 0.5 7.6 @ 100 4.77 @ 300 14 6.0 0.2 10.7 @ 100 4.77 @ 300 13 6.0 0.3 10.7 @ 100 4.77 @ 300 18 6.0 0.4 10.7 @ 100 4.77 @ 300 22 6.0 0.5 10.7 @ 100 4.77 @ 300 27 6.0 0.2 11.9 @ 100 4.77 @ 300 16 6.0 0.3 11.9 @ 100 4.77 @ 300 22 6.0 0.4 11.9 @ 100 4.77 @ 300 27 6.0 0.5 11.9 @ 100 4.77 @ 300 33
The slab mesh reinforcement is used on footing construction, beam and piers of waffle rafts. The slab mesh was made by Heyou wire mesh factory accordance with AS NZS 4671-2001. the popular specification is SL102, SL92, SL82, SL72, SL63, SL53, L8TM, L11TM, L12TM in the Australia and New Zealand civil engineeing. The slab mesh reinforcement includes reinforcement mesh and trench mesh. Aoriding to different construction site, they use the spcification of slab meshes are difference. The full of slab mesh reinforcement specification as below: REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Slab mesh reinforcement for footing slab, beam and piers RIBBED RECTANGULAR MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG RL718 6 x 2.4m Sheet 25 x 6.75 @ 100 30 x 7.60 @ 200 67 RL818 6 x 2.4m Sheet 25 x 7.60 @ 100 30 x 7.60 @ 200 79 RL918 6 x 2.4m Sheet 25 x 8.60 @ 100 30 x 7.60 @ 200 93 RL1018 6 x 2.4m Sheet 25 x 9.50 @ 100 30 x 7.60 @ 200 109 RL1118 6 x 2.4m Sheet 25 x 10.70 @ 100 30 x 7.60 @ 200 130 RL1218 6 x 2.4m Sheet 25 x 11.90 @ 100 30 x 7.60 @ 200 157 Slab mesh reinforcement for footing slab, beam and piers REINFORCING MESH TO AS/NZS4671:2001 / RIBBED SQUARE MESH 6.0 X 2.4 METRES Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL52 6 x 2.4m Sheet 10 x4.77 @ 200 + 4 x 4.00 @ 100 30 x 4.77 @ 200 21 SL62 6 x 2.4m Sheet 10 x 6.00 @ 200 + 4 x 4.24 @ 100 30 x 6.00 @ 200 33 SL72 6 x 2.4m Sheet 10 x 6.75 @ 200 + 4 x 4.77 @ 100 30 x 6.75 @ 200 41 SL82 6 x 2.4m Sheet 10 x 7.60 @ 200 + 4 x 5.37 @ 100 30 x 7.60 @ 200 52 SL92 6 x 2.4m Sheet 10 x 8.60 @ 200 + 4 x 6.00 @ 100 30 x 8.60 @ 200 66 SL102 6 x 2.4m Sheet 10 x 9.50 @ 200 + 4 x 6.75 @ 100 30 x 9.50 @ 200 80 SL81 6 x 2.4m Sheet 25 x 7.60 @ 100 60 x 7.60 @ 100 105 Slab mesh reinforcement for footing slab, beam and piers SQUARE MESH 300 X 300 SPACING TO AS/NZS4671: 2001 Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL53 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 14 SL63 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 21
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm. 1. The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45°. The angle scope is greater than 45° and is less than 70°, the rib height is from 0.025d to 0.10d. 2. The reinforcing mesh panel includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost. 3.Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of reinforcing mesh panel has single bars, twin bars or combination of single bars and twin bars. 4.The technical data of reinforcing mesh panle is contained composition and characteristic mechanical porperties of reinforcing steels. Common size of Squre reinforcing mesh panel for Austialian Market Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6 x2.4 m sheets Cross-sectional area/m width No. x dia., mm Pitch@mm No. x dia., mm Pitch@mm Unit area kg/sqm Sheet, kg Long'l bars sqmm/m Cross bars sqmm/m Squre, with edge side-lapping bars SL102 10 x 9.5 + 4 x 6.75 200100 30 x 9.5 200 5.6 80 354 354 SL92 10 X 8.6 + 4 X 6.0 200100 30 x 8.6 200 4.6 66 290 290 SL82 10 x 7.6 + 4 x 6.0 200100 30 x 7.6 200 3.6 52 227 227 SL72 10 x 6.75 + 4 x 5.0 200100 30 x 6.75 200 2.8 41 179 179 SL62 10 x 6.0 + 4 x 5.0 200100 30 x 6.0 200 2.2 33 141 141 Squre, without edge side - lapping bars SL81 25 X 7.6 100 60 x 7.6 100 7.1 105 454 454 How can we conctrol our products quality for exporting Autralia? Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechnical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3. Secondly, the panel size tolerances meassure way as: a. Panel Size dimensionsâ?¤6m in length, there is 40mm tolerances. b. Panel size dimensionsï¼?6m in length, the tolerance is ±0.7% c. Wire diameter and mesh size measure and weld shear resistance test conformance to AS NZS 4761-2001 and as per contract. d. Weigh the each bundle weight to calculate each panel weight.
Welded Wire Reinforcement (WWR) provides the exact size of reinforcement where needed through variable bar size and spacing, thereby reducing steel waste. Plain Square Mesh sheets are a multi-purpose mesh and complies with AS/NZS 4671 : 2001 Steel reinforcing materials. Plain Square Mesh sheets are available in 6 x 2.4 m. Associated standards: AS/NZS 4671 : 2001 Steel reinforcing materials Application: Welded Wire Reinforcement can be used for: Slab on Grade reinforcement Floor and Walls Systems Topping Slabs Architectural precast wall panels Tilt-up construction wall systems Shear walls Retaining walls Mechanically Stabilized Earth (M.S.E.) reinforcement
reinforcing mesh SL82 1. Material: Low carbon steel ribbed wire 2. Standard: AS/NZS4671:2001 3. Main hole size: 200x200mm, edge 200x100mm 4. Wire diameter: main wire 7.6mm, 4 longitude edge wire 5.37mm 5. Sheet size: 2.4m x 6m 6. Application: bridge, road, building, sidewalk,etc. 7. Package: steel belt, pallet 8. Delivery: within 15 days for one container 9. Payment: T/T, 30% deposit, 70% by the copy of B/L
Wire diameter for welded steel bar panels: ranges from 5mm to 12mm Welded bar panels opening: 50mm to 300mm Panel length: 100cm to 1200cm Panel width: 100cm to 300cm
Reinforcing mesh SL82.
Brick wall reinforcement mesh is welded wire sheet for reinforced concrete construction. It is used in building surface, wall, ground, bridge, bank and airport. And its feature is that welding spots of warp wire and weft wire are on the same surface. Wire diameter: 2.5-6.0 mm Width: 5cm-27cm Length: 3mm. Spacing: 40cm Surface treatment: welded after hot dipped galvanized, welded after electro galvanized, welded before electro galvanized, welded before hot dipped galvanized, welded by stainless steel wire. We have two types of brick wall reinforcement mesh: truss-mesh reinforcement and ladder-mesh reinforcement. Package: carton/pallet/plastic wrapped. Package: carton/pallet/plastic wrapped.
(1) Reinforce rib Mesh is the panel that adding same wire same material’s wire mesh panel in vertical or horizontal weaving direction.its tensile strength higher than usual mesh panel, the reinforce rib’s diameter is not less than selvage wire diameter. the reinforce rib mesh can absorb and down low the Gap value of tensile stress caused by gap and transportation, especially in the high tensile strength. (2) Reinforce gabion is formed from gabion mesh and gabion panel, gabion panel extended into the soil as the reinforce mesh for the gabion mesh.make use of friction between soil and panel to supply Stabilizing force, have better Environmental compatibility.
