Construction Reinforcement Mesh

Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.

Reinforcing wire mesh Reinforcing construction mesh is one kind of new structural purpose wall material, it may substitute the brick wall to make each kind of bearing wall, the non- bearing wall and the floor, the balcony and so on. It has the expanded building useable area (10%-15%), the heat insulation, sound-insulated, the earthquake resistance, the waterproofing, the construction is simple, is self-possessed lightly and so on the characteristic, at the same time reduced the project construction cost greatly.

Concrete Reinforced Mesh is widely used as bridge reinforced mesh, road construction mesh, floor reinforced mesh, trench mesh, Concrete slab mesh, Masonry mesh and brick wall reinforced mesh, which is used in construction reinforcement, the ground for the tunnels, bridges, highway and airport, wharf and wall. It is a type of convenient and economical reinforcement option for modern concrete structures. Specification of concrete reinforced mesh: (1)Material:plain steel bar, stainless steel rebar rods. (2)Steel rods style: ribbed or smooth. (3)Rebar Diameter: 3 mm - 40 mm. (4)Mesh shape: square or rectangular . (5)Distance between rods : 50,100, 150, 200,300, 400 mm. (6)Mesh sheet width: from 650 mm to 3800 mm. (7)Mesh sheet length: 850 mm, 6 m, 9 m, 12 m. Features of concrete reinforced mesh: (1)High strength. (2)Anti-crack and anti-shock. (3)Hot-dip galvanized or epoxy coating after the manufactures (4)Anti-corrosion, acid-resisting. (5)Easy to install Applications of concrete reinforced mesh: (1)Concrete reinforced mesh is used as bridge reinforced construction and building, like bridge girders, bridge spans, bridge decks. (2)Concrete reinforcing mesh used in median barriers, tunnel segments, box culverts, airport and wharf. (3)Concrete reinforcing mesh used in residential, industrial and road construction, such as concrete footpaths and industrial and commercial ground slabs, precast panel construction and residential slabs and footings. (4)Constructional uses: block slab structure reinforcing, and hollowed slabs reinforcement, building wall reinforcement and support wall reinforcement. (5)Used as coal mine supporting mesh for coal mine roadway supporting.

K188/K335 reinforcement wire mesh Anping Heyou Wire Mesh Products Co.Ltd can supply reinforcement wire mesh conformance with Swiss Standard SIA 16211 S550. Its has widely useage for foudations beams,slabs,walls,columns,foundation slabs,footings,tunnel,coal and mine,subway tunnel etc. The mesh spacing is 150mm,and normal sheet size is 2m*5m. The skatch of K188/K335 reinforcement wire mesh NL= Number of longitudinal bars PL= pitch of longitudinal bars dL= diameter of longitudinal bars NC=Number of transverse bars L= length of longitudinal bar B=Length of transverse bar u1=Overhang of longitudinal bars u2=Overhang of longitudinal bars The specification of reinforcement wire mesh conformance with Swiss Standard SIA 16211 S550 mesh type Pitch of wires(mm) diameter of wire(mm) Per meter area sqm/m Dimension of Mesh Area of Mesh(sqmm) Mass (kg/sqm) Weight of Mesh(kg) pL pC dL dC long cross L(mm) B(mm) K188 6 6 150 150 188 188 5000 2000 10 3.091 30.192 K335 8 8 150 150 335 335 5000 2000 10 5.372 53.72 Z248.5 6/4.5 7 150 150 248 257 5000 2000 10 3.422 34.22 Z248.6 6/4.5 7 150 150 248 257 6000 2000 12 3.472 41.668 Z348.5 7/5.5 8 150 150 348 335 5000 2000 10 4.628 46.28 Z348.6 7/5.5 8 150 150 348 335 6000 2000 12 4.694 56.326 Z442.5 8.0/6.0 9 150 150 442 424 5000 2000 10 5.857 58.57 Z442.6 8.0/6.0 9 150 150 442 424 6000 2000 12 5.94 71.282 Z558.5 8.5/7.5 10 150 150 558 524 5000 2000 10 7.315 73.15 Z558.6 8.5/7.5 10 150 150 558 524 6000 2000 12 7.418 89.014 The details of the reinforcement wire mesh as below: Apparent three face indentation om the surface The weld spot firmly and strong Homogeneous mesh space Flat mesh surface The inspection of the reinforcement wire mesh The wire diameter inspected by micrometer The mesh space messured by bemier caliper The width messured by flexible rule The length messured by flexible rule The Tensile strength and yield stress inspected by tensile machine weld shear resistance test The packing and shipment The bundle of sheet size 2m x5m Shipment for loading container Application site of reinforcement wire mesh Reinforcement wire mesh used on bridge and pier Reinforcement wire mesh used on construction footing foudation Reinforcement wire mesh used on flooring slabs Reinforcement wire mesh used on foudation beams

According to the wire diameter and opening, we can offer standard welded wire mesh or heavy type welded wire mesh. Differernt processing means we offer for your choice include: hot-dip galvanized welding wire mesh; hot-dip galvanized before welding wire mesh; electric-galvanised after welding wire mesh; electric-galvanised before welding wire mesh. In accordance with the customer's request.

Concrete reinforcing mesh 1.Wire diameter:3mm-14mm 2.Mesh:5*5cm, 10*10cm, 10*20cm, 20*20cm, 10*30cm, 30*30cm 3.Iso & sgs Packed with the iron or wooden pallet.

Square Mesh products in 6.0m x 2.4m sheet sizes are general-purpose ribbed mesh sheet used to reinforce concrete slabs. *SPECIFICATIONS* Material Carbon Steel Grade 500 Mpa Length 6000mm x 2400mm Main Wire (mm): 6.00@200, 6.75@200, 7.60@200, 8.60@200, 9.50@200, 7.60@100 mm *STANDARDS* Manufactured in accordance with AS/NZS 4671:2019 ACRS Certified NOTE - Can be manufactured in accordance with various international standards (EN, BS, ASTM and AS/NZS) *PACKAGING* Unit of Measure Sheets Pack Type Bundles FCL Quantity 25MT

Trench Mesh products in 6.0m x (200mm, 300mm, 400mm, and 500mm) sheet sizes and are a general-purpose ribbed mesh sheet used to reinforce concrete slabs with a narrow profile. *SPECIFICATIONS* Material Carbon Steel Grade 500 Mpa Length 6000mm x (200mm, 300mm, 400mm, or 500mm); width is dependent on number of wires (3,4, 5, or 6) Main Wire: 7.60@100, 10.70@100, 11.90@100 mm Cross Wire: 4.00@300, 4.75@300 mm *STANDARDS* Manufactured in accordance with AS/NZS 4671:2019 ACRS Certified NOTE - Can be manufactured in accordance with various international standards (EN, BS, ASTM and AS/NZS) *PACKAGING* Unit of Measure Sheets Pack Type Bundles FCL Quantity 25MT