Reinforcing Trench Mesh

Trench Mesh products in 6.0m x (200mm, 300mm, 400mm, and 500mm) sheet sizes and are a general-purpose ribbed mesh sheet used to reinforce concrete slabs with a narrow profile.

*SPECIFICATIONS*
Material Carbon Steel
Grade 500 Mpa
Length 6000mm x (200mm, 300mm, 400mm, or 500mm);
width is dependent on number of wires (3,4, 5, or 6)
Main Wire: 7.60@100, 10.70@100, 11.90@100 mm
Cross Wire: 4.00@300, 4.75@300 mm

*STANDARDS*
Manufactured in accordance with AS/NZS 4671:2019
ACRS Certified
NOTE - Can be manufactured in accordance with various international standards (EN, BS, ASTM and AS/NZS)

*PACKAGING*
Unit of Measure Sheets
Pack Type Bundles
FCL Quantity 25MT

Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire

It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam.

Specification of trench mesh reinforcement

Surface treatment:galvanized or drawn wire

Material: R250N, D500N, D500L, D300E, D500E

The Tensile strength is 300Mpa.

The trench mesh was produced by standard AS NZS 4671-2001

Width: 0.2m - 2.3m

Length: 6m

REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8
L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2
L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6
L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9
L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9
L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72
L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13
L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7
L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3
L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8
L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34
L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1
L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3
L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8
L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3
L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8
L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1

Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers

And Alls of using is accordance to AS NZS 2870-2011.

1. Footing slap

The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments.

The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different.

2. Waffle rafts beam and piers

The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft:

(a). pier to be located on the intersection of every third internal beam.

(b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.

Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire

It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam.

Specification of trench mesh reinforcement

Surface treatment:galvanized or drawn wire

Material: R250N, D500N, D500L, D300E, D500E

The Tensile strength is 300Mpa.

The trench mesh was produced by standard AS NZS 4671-2001

Width: 0.2m - 2.3m

Length: 6m

REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH
Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG
L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8
L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2
L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6
L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9
L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9
L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72
L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13
L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7
L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3
L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8
L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34
L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1
L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3
L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8
L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3
L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8
L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1
And Alls of using is accordance to AS NZS 2870-2011.

1. Footing slap

The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments.

The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different.

2. Waffle rafts beam and piers

The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft:

(a). pier to be located on the intersection of every third internal beam.

(b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.

Welded Wire Reinforcement (WWR) provides the exact size of reinforcement where needed through variable bar size and spacing, thereby reducing steel waste.

Plain Square Mesh sheets are a multi-purpose mesh and complies with AS/NZS 4671 : 2001 Steel reinforcing materials.

Plain Square Mesh sheets are available in 6 x 2.4 m.

Associated standards:
AS/NZS 4671 : 2001 Steel reinforcing materials
Application:

Welded Wire Reinforcement can be used for:

Slab on Grade reinforcement

Floor and Walls Systems

Topping Slabs

Architectural precast wall panels

Tilt-up construction wall systems

Shear walls

Retaining walls

Mechanically Stabilized Earth (M.S.E.) reinforcement

reinforcing mesh SL82

1. Material: Low carbon steel ribbed wire
2. Standard: AS/NZS4671:2001
3. Main hole size: 200x200mm, edge 200x100mm
4. Wire diameter: main wire 7.6mm, 4 longitude edge wire 5.37mm
5. Sheet size: 2.4m x 6m
6. Application: bridge, road, building, sidewalk,etc.
7. Package: steel belt, pallet
8. Delivery: within 15 days for one container
9. Payment: T/T, 30% deposit, 70% by the copy of B/L

RL1218 concrete reinforcement welded mesh
25*11.90@100 by 30*7.60@200
Main hole size: 200x200mm, edge 200x100mm
Sheet size: 2.4m x 6m

Concrete Reinforced Mesh is widely used as bridge reinforced mesh, road construction mesh, floor reinforced mesh, trench mesh, Concrete slab mesh, Masonry mesh and brick wall reinforced mesh, which is used in construction reinforcement, the ground for the tunnels, bridges, highway and airport, wharf and wall. It is a type of convenient and economical reinforcement option for modern concrete structures.

Specification of concrete reinforced mesh:
(1)Material:plain steel bar, stainless steel rebar rods.
(2)Steel rods style: ribbed or smooth.
(3)Rebar Diameter: 3 mm - 40 mm.
(4)Mesh shape: square or rectangular .
(5)Distance between rods : 50,100, 150, 200,300, 400 mm.
(6)Mesh sheet width: from 650 mm to 3800 mm.
(7)Mesh sheet length: 850 mm, 6 m, 9 m, 12 m.

Features of concrete reinforced mesh:
(1)High strength.
(2)Anti-crack and anti-shock.
(3)Hot-dip galvanized or epoxy coating after the manufactures
(4)Anti-corrosion, acid-resisting.
(5)Easy to install

Applications of concrete reinforced mesh:
(1)Concrete reinforced mesh is used as bridge reinforced construction and building, like bridge girders, bridge spans, bridge decks.
(2)Concrete reinforcing mesh used in median barriers, tunnel segments, box culverts, airport and wharf.
(3)Concrete reinforcing mesh used in residential, industrial and road construction, such as concrete footpaths and industrial and commercial ground slabs, precast panel construction and residential slabs and footings.
(4)Constructional uses: block slab structure reinforcing, and hollowed slabs reinforcement, building wall reinforcement and support wall reinforcement.
(5)Used as coal mine supporting mesh for coal mine roadway supporting.

concrete slab square mesh provides the exact size of reinforcement where needed through variable bar

size and spacing, thereby reducing steel waste.



Plain Square Mesh sheets are a multi-purpose mesh and complies with AS/NZS 4671 : 2001 Steel reinforcing materials.

Plain Square Mesh sheets are available in 6 x 2.4 m.



Associated standards:
AS/NZS 4671 : 2001 Steel reinforcing materials



Application:

Welded Wire Reinforcement can be used for:

Slab on Grade reinforcement

Floor and Walls Systems

Topping Slabs

Architectural precast wall panels

Tilt-up construction wall systems

Shear walls

Retaining walls

Mechanically Stabilized Earth (M.S.E.) reinforcement

Welded Wire Reinforcement (WWR) provides the exact size of reinforcement where needed through variable bar

size and spacing, thereby reducing steel waste.



Plain Square Mesh sheets are a multi-purpose mesh and complies with AS/NZS 4671 : 2001 Steel reinforcing materials.

Plain Square Mesh sheets are available in 6 x 2.4 m.

SL72 6.75@200 6.75@200 41kg