Hydraulic Cartridge Valves Suppliers and Manufacturers

At the beginning of this year, received an order from African customer for excavators with a delivery time of 2 months, which means that all accessories must be in place within 1 month, including 600 hydraulic cartridge valves. The production time for the factory is a little more than 2 weeks. The purchaser Peter sent the order information of the hydraulic cartridge valve to all the hydraulic valve manufacturers he contacted before at the first time. More than 20 hydraulic valve manufacturers said that they could not complete the order of the hydraulic cartridge valve in such a short time, and it would take at least 3 - 4 weeks. His supervisor was not satisfied with this delivery time and asked him to find a new hydraulic valve manufacturer. After the email was sent, there was basically no sound. Peter was very helpless and worried. Peter asked Mark for help. HYDRAULIC VALVE to ask if could produce 600 hydraulic cartridge valves in 2 weeks and CC Peter, and joking at the end of the email that if HYDRAULIC VALVE could not complete the hydraulic cartridge valve order, then there is no need to waste time on looking for a new hydraulic valve manufacturer. According to the drawings they sent, technical department found that this was very close to the hydraulic cartridge valve supplied to a Russian customer last year, so the time in the early stage of the production of the hydraulic cartridge valve was saved. After the price of the hydraulic cartridge valve was approved, the process data could be configured on the computer on the same day and the production could be carried out the next day. 2 weeks later, 600 hydraulic cartridge valves were delivered on time, which was the first of all the accessories purchased by Peter to arrive at the company's warehouse. Peter didn't expect that the hydraulic cartridge valve he was most worried about was the first to be completed. Peter appreciated the advice from Mark and was also surprised that could complete this in 2 weeks, while his previous hydraulic valve suppliers needed 3-4 weeks. Mark told : 1. is his most trusted hydraulic valve manufacturer. can surprise him every time when the hydraulic valve order is urgent. 2. has a large amount of data storage and clear classification. For hydraulic valves with relevant data, they can use the most advanced UG / SOLIDWORK software and finite element analysis method to configure process data in 2 hours, which is 3-6 times faster than that of other suppliers. 3. is equipped with advanced machine tools imported from Swiss, coupled with their own modified fixtures, the production speed is accelerated and man-made errors are avoided at the same time. After listening to the introduction realized that only a good hydraulic valve supplier can make his purchasing smooth. successfully completed this urgent order.

Andy is our old hydraulic valve customer in the The hydraulic cartridge valves he purchased from in previous years always has a standard of machining surface roughness around 0.8m. In last year, Andy sent an email to inform us that in the future, the machining surface accuracy of their hydraulic cartridge valves will be improved to within 0.3m. engineers believe that based on the current equipment system, it is very difficult to improve the machining surface accuracy of hydraulic cartridge valves to 0.3 m. It is also very difficult to find such a hydraulic cartridge valve manufacturer I know that has only two options, either give up the business of his hydraulic cartridge valves or accept his accuracy standard. This is the first time I have faced the choice of "standing in line" since I joined the hydraulic valve industry. The cooperation with Andy has always been trustworthy, pleasant and efficient. doesn't want to give up such customers. After two rounds of communication internally, technical team has not reached a consensus. I have to call my retired master and hope to hear his opinions. My master told me that this is a rare opportunity to catch up with and surpass the accuracy of international hydraulic cartridge valves. The roughness of the working surface under 0.3m is rare in , but some European hydraulic cartridge valve manufacturers have this strength. must first start with the equipment, and then select the most experienced operators from the factory for special aircraft training, so as to have the opportunity to compete with those top European hydraulic cartridge valve manufacturers. American HARDINGE precision CNC lathe is worthy of a try. At present, none of the domestic hydraulic cartridge valve manufacturers have this equipment. After contacting the equipment manufacturer, technical team took the hydraulic cartridge valves produced for Andy before to the equipment factory, and asked the engineer of the equipment manufacturer to go directly to the machine for proofing. A week later, we sent the hydraulic cartridge valve samples to Andy and asked them to test the accuracy parameters. Two weeks later, Andy informed that the previous hydraulic cartridge valve accuracy test was completed twice. This time, hydraulic cartridge valve was tested 4 times, and the accuracy fully met the standard. At the same time, he told me that after receiving the accuracy improvement notice, the other 3 domestic hydraulic cartridge valve manufacturers directly gave up, and only dared to test the sample and succeeded in one test. He was very surprised. The machine tool to be introduced by has advantages in accuracy. The parameters of the machine tool: spindle speed up to 6000r/ min, spindle radial run out 0.0008mm, positioning accuracy (X/Z)

Brooke is the purchasing manager of the American company Vickers and has been working with AAK for more than 6 years. One morning last month, he emailed us that his job was finally saved. I was surprised how a veteran suddenly said that he had finally "saved his job". In private, I learned that it was because he had some disagreements with his owner and quarreled. The owner almost let him go. Because his owner is not satisfied with the price of AAK, sometimes the price of AAK for the same hydraulic valve will be more than 20% higher than that of other Chinese hydraulic valve manufacturers. At the cost meeting last month, the owner proposed to replace the Chinese hydraulic valve manufacturer, but Brooke insisted that AAK is the most cost-effective Chinese hydraulic valve manufacturer, so it is not recommended to replace it. On the contrary, he can only leave. The year before last, the owner went to Shanghai PTC exhibition with him to develop suitable Chinese hydraulic valve manufacturers for cooperation. They did get acquainted with many Chinese hydraulic valve manufacturers at the exhibition, but after more than 2 years of testing samples and running in, Brooke found that there is really no second Chinese hydraulic valve manufacturer that can compare with AAK in all aspects. AAK is not only reliable, but also has temperature, whether it is cooperation, delivery, quality, after-sales etc. Brooke remembers the support and help from AAK hydraulic valve over the years. On one occasion, due to the urgent delivery time of a South African customer, Brooke could not find a factory with stock at that time and could only customize it. Most Chinese hydraulic valve manufacturers said that the lead time from sampling to delivery should be at least 2 months. AAK stopped a production line and asked technicians to work overtime to speed up the production. Samples can be produced in 30 days and shipped in 45 days. It is precisely because of the temperature of AAK that Vickers has the opportunity to cooperate with this big customer in South Africa. Every time, AAK products can be successful at one time during testing. They are the best among all Chinese hydraulic valve manufacturers in terms of accuracy, concentricity, fatigue resistance and durability. Brooke's deepest memory is that one time, the South African customer mentioned that the hydraulic valve used for more than 2 years often stuck during work and asked for replacement. After receiving the news, AAK immediately told Brooke to ask the customer to return the goods. After inspection, it turned out that the hydraulic oil used by the South African customer was not clean and caused the problem. Later, AAK disassembled and cleaned the valve and sent it again, and asked the customer to change the hydraulic oil. Until now, no problem has been mentioned. If this happened to other Chinese hydraulic valve manufacturers, their reply must be that this has passed the warranty period.

is a hydraulic customer from the . Recently, a batch of hydraulic cartridge valves he temporarily purchased were in trouble. Because the parameters from customer were not complete, he used the same model product recommended by the hydraulic valve manufacturer instead. During testing, the flow parameters were not equal. The rated flow of the hydraulic cartridge valve was smaller than the working flow and could not be used normally, which wasted more than 10 days and the delivery time was urgent. He contacted with more than 10 hydraulic valve manufacturers. For hydraulic cartridge valves of the same model, their rated flow setting is either smaller than the working flow or close to the working flow of the system. was very distressed that no hydraulic cartridge valve has a rated flow setting greater than the working flow. found HYDRAULIC VALVE on Google. He felt that HYDRAULIC VALVE was a little different from other hydraulic valve manufacturers. With a try attitude, actively contacted us and sent us the product picture and product model of this hydraulic cartridge valve. He just emphasized that the rated flow must be greater than the working flow and asked us to recommend the hydraulic cartridge valve of the same model, there was no any parameter information. After careful comparison, engineers sent pictures and drawings of a hydraulic cartridge valve of the same model. asked us to send the hydraulic cartridge valve samples as soon as possible. On the 3rd day after receiving the hydraulic cartridge valve sample, emailed to inform that the rated flow of hydraulic cartridge valve can really meet the normal operation of their current hydraulic system. expressed his curiosity that the hydraulic cartridge valve model recommended by is consistent with that recommended by other manufacturers. How can there be such a big difference in the rated flow setting For the selection of flow specifications of hydraulic valves, the settings of each factory are different. If the rated flow of the valve is close to the working flow of the system, this situation is the most economical and cost-effective, and it is also the first choice of nearly 90% of hydraulic valve manufacturers. But there may be a problem, once the working flow in the hydraulic system exceeds the rated flow, it will cause hydraulic clamping and affect the hydraulic power. It will also have an adverse impact on the hydraulic system of the valve. To be safe, when all cartridge valves are produced, will give priority to the maximum flow that may pass through the circuit where the hydraulic valve is located, and the setting of rated flow is greater than the maximum flow of operation, so as to ensure the normal operation of whole system, which is also the reason why most customers prefer .

Nearly 90% of the hydraulic cartridge valve manufacturers in Ningbo can not achieve the filtration accuracy as high as 10 Microns. But AAK is 1 of the less than 10% hydraulic cartridge valve manufacturers with a filtering accuracy up to 10 Microns. Dylan came to AAK HYDRAULIC VALVE with a very special two position two-way hydraulic cartridge valve. I knew he should have encountered a problem. For this special hydraulic cartridge valve, the filtration accuracy of 10 Microns was the minimum requirement. Dylan consulted the existing cooperated hydraulic cartridge valve manufacturers, but none of them could meet the requirement. Most hydraulic cartridge valve manufacturers said that the filtering accuracy of 25 Microns is 100% no problem. Only 1 hydraulic cartridge valve manufacturer gave feedback and was 70% sure that the filtering accuracy could reach 10 Microns. Dylan directly asked me, is it really difficult for these hydraulic cartridge valve manufacturers in Ningbo to achieve the filtering accuracy of 10 microns? How can so many hydraulic cartridge valve manufacturers have said that they can only achieve the filtering accuracy of 25 Microns? I could understand his helplessness and confusion. This is because that the conventional hydraulic cartridge valve manufacturers produce hydraulic valves according to domestic hydraulic standards in China. Not only 1 or 2, but nearly 90% of hydraulic cartridge valve manufacturers, can only able to get the filter element aperture reaches 25�¼m. We AAK HYDRAULIC VALVE also used conventional filters at the beginning, and the filtration accuracy was also based on domestic standards. 3 years ago, a German hydraulic valve customer requested the accuracy requirement of 10 Microns, which was not only a stimulus but also a challenge for us. After more than 2 months of adjusting, we improved the process on the small sample, and adjusted the equipment parameters until it was configured to a high-precision filter and cooperated with AAK special hydraulic oil, so that the filtration accuracy of particles in the hydraulic oil could be controlled to 10m. 1 year later, some hydraulic cartridge valve manufacturers learned that AAK had upgraded with high-precision filters and followed suit. However, due to technical constraints, many hydraulic cartridge valve manufacturers still failed to meet the standard. Under the same working conditions, if the hydraulic cartridge valves from these hydraulic cartridge valve manufacturers have a service life of 2 years, the service life of AAK hydraulic cartridge valves can be extended to 3-4 years. Dylan was surprised that we had mass produced hydraulic cartridge valves with filtration accuracy up to 10 Microns 3 years ago, but only 1 of his current hydraulic cartridge valve manufacturers could do it, and with only 70% sure. Dylan took out the drawings and asked us to send samples of this special hydraulic cartridge valve within 20 days.

Patrick, an old customer in the Netherlands, used to buy our hydraulic cartridge valves. In the first half of the year, he purchased a batch of hydraulic valve blocks from another hydraulic valve manufacturer, but he had received a strange complaint from users in recent weeks. The hydraulic oil deteriorated suddenly. After stopping the machine to check the hydraulic oil, it was found that there were small iron filings inside the oil. After disassembling the whole hydraulic valve, it was found that the valve spool also showed signs of wear. The customer judged that there were iron filings in this batch of hydraulic valve blocks. Patrick discussed with the hydraulic valve block manufacturer about how to deal with this quality complaint. The manufacturer replied that it was the problem of hydraulic oil, not the hydraulic valve block. So this problem was stuck here. Patrick emailed me and asked if I knew this hydraulic valve block manufacturer and whether I could mediate and solve the problem. When I received the drawings of the hydraulic valve block purchased by Patrick this time, I felt that the iron filings probably came from the hydraulic valve block, because the intersecting processing channels of this hydraulic valve block were complex. With Patrick's appeal, I went to the hydraulic valve block factory. The overall feeling of the factory was still good, but the cleaning process before hydraulic valve block packaging did not accord with the process and details in my mind. When I came back, I emailed Patrick. The manufacturer should understand that the problem of iron filings lay with them. However, according to the current iron filings removal process in this factory, even if replenishment, it was difficult to completely avoid iron filings. So he didn't want to reproduce and couldn't solve the problem, he had to perfunctory your demands. Patrick didn't reply to my email for 2 days. When I asked him what else he needed me to do in this matter, he said that he had a big headache these 2 days. The owner asked him to find a new hydraulic valve block manufacturer to replenish part of the hydraulic valve blocks to take care of the customer's dissatisfaction with quality. I reminded him that there were few hydraulic valve manufacturers that could do this type of hydraulic valves with many slender holes. AAK HYDRAULIC VALVE solved a similar problem of iron filings of hydraulic valve block last month, and I sent him the pictures of hydraulic valve block for reference. The next day, Patrick asked us how long it would take to produce 200 hydraulic valve blocks, which was the minimum replenishment quantity required by the customer. When the replenishment order was confirmed, Patrick was relieved. How does AAK hydraulic valve remove iron filings from hydraulic valve block Firstly, the hydraulic valve block is boiled with high-temperature alkaline water to make the iron filings of the hydraulic valve block lose magnetism, and then

AAK HYDRAULIC VALVE Classified the Types of Hydraulic Cartridge Valves from the Perspective of Installation, and Berge Puts Down His Uneasy Heart The types of hydraulic cartridge valves can be classified from different angles. Sometimes, buyers who purchase hydraulic cartridge valves are confused. After all, they are not engineers. In order to classify more simply and intuitively, AAK HYDRAULIC VALVE describes the types of hydraulic cartridge valves from the most extensive installation point of view. In this way, we can divide the hydraulic cartridge valves into 3 types: Insert-type, Slide-in and Screw-in. Berge, an old British hydraulic valve customer, was transferred from the quality control department to the import department. He is a very studious buyer. Maybe it's fate, we often discuss some knowledge points about hydraulic valves. Some time ago, he didn't understand that every time, when the domestic hydraulic valve manufacturers receive an inquiry about his hydraulic cartridge valve, they always ask about the type of hydraulic cartridge valve. The question about the type of hydraulic cartridge valve made him very nervous and helpless. Indeed, there are many types of hydraulic cartridge valves now, from the perspective of function, hole type and scene. We found that they are most commonly classified from the perspective of installation, which is easy to understand and remember. I summarized our hydraulic cartridge valve types to Berge. After reading my following report about the types of the hydraulic cartridge valves, he told me that this classification for the hydraulic cartridge valve types can basically cover more than 80% of the hydraulic cartridge valves. Here, I'll also share with you the types of hydraulic cartridge valves I gave him. Common types of hydraulic cartridge valves are as follows: The Insert-type hydraulic cartridge valves: completely enters the inside of the valve block and does not expose any part outside the valve block. It is positioned by its own thread or other components such as pipe joint, snap ring, retaining ring etc. For example, hydraulic check valve and two-way hydraulic flow regulating valve have this design. The slide-in hydraulic cartridge valves: it does not have installation threads itself, and the valve spool needs to be used together with the cover plate. The valve spool is integrated in the valve block to switch the oil circuit on and off through pressure and spring force. Different cover plates are used to realize direction control, pressure control and flow control. Screw-in hydraulic cartridge valves, that is, hydraulic threaded cartridge valves, have different brands and different hole types, which are usually unable to be interchanged in installation. At present, there are 3 commonly used pass types: ISO7789, SAE and SUN.

Patrick and I know each other at the PTC exhibition in Shanghai. He has worked in HAENCHEN hydraulic equipment company in Germany for a long time. The first thing he said when he saw me was that â??I was attracted by the slogan "Hydraulic valve manufacturer of the world's top 500 companies" on your AAK boothâ??. We talked about the hydraulic threaded cartridge valves for more than half an hour, especially introduced the difference of AAK hydraulic threaded cartridge valves on the specific details. He was surprised that the details of AAK had caught up with his local hydraulic valve manufacturers in Germany. Shortly after the exhibition, Patrick emailed us a hydraulic threaded cartridge valve with high parameter requirements. In particular, the durability of the hydraulic threaded cartridge valve should be more than 2 million times. All quality details should be compared with their local suppliers in Germany. The drawings attached to the email indicate the detailed data and working condition requirements. AAK is required to send 12 hydraulic threaded cartridge valve samples within 4 weeks. After analysis and comparison, AAK engineers found that this hydraulic threaded cartridge valve is not only durable for more than 2 million times, but also has high accuracy requirements. In particular, the internal leakage requirement of hydraulic threaded cartridge valve is 2drops / min, which is 60% higher than the international general standard. Although the requirements are high, we are still confident. 4 weeks later, AAK sent 12 hydraulic threaded cartridge valve samples. A month after the hydraulic threaded cartridge valve samples were sent, Patrick emailed that AAK did make him realize that it was different from other hydraulic valve manufacturers. At that time, he emailed to 4 Chinese hydraulic threaded cartridge valve manufacturers and a local manufacturer in Germany. Two of the 4 Chinese hydraulic valve manufacturers gave up directly. Only AAK and another hydraulic thread cartridge valve manufacturer confirmed to make samples. They tested and compared the sample parameters of the three factories. AAK's accuracy and durability are not only much higher than those of its Chinese counterparts, but also benchmarked with their local manufacturer in Germany. Although the quotation of AAK hydraulic threaded cartridge valve is much higher than that of its Chinese counterparts, it still has advantages over the hydraulic threaded cartridge valve purchased locally in Germany. Purchasing from AAK is the best embodiment of cost performance. AAK hydraulic threaded cartridge valve has three absolute advantages and has already surpassed its domestic counterparts. 1. AAK has a high-precision CNC machining center imported from Switzerland and various independent fixtures upgraded and refitted by itself, which eliminates human errors and ensures the first step of accuracy.

Walt placed an order for 1000 hydraulic threaded cartridge valves at one time last week, which surprised me. Three years ago, I met Walt from an American company at the Shanghai PTC exhibition. He communicated with us at our booth for more than half an hour. After the exhibition, Walt sent an email saying that his company happened to have a newly developed hydraulic equipment, which needs to use hydraulic threaded cartridge valves. He asked AAK to urgently provide 30 samples of hydraulic threaded cartridge valves according to his drawings. AAK sent out 30 hydraulic threaded cartridge valves after 25 days. After this, there was no inquiry for any hydraulic threaded cartridge valves from him. Half a year later, Walt sent a new test order of 40pcs for another new hydraulic threaded cartridge valve. Same as last time, there is no further news after delivery. In this way, we just received 2 test orders in about 2 years. I thought that there should be a mistake on the quantity of this large order of hydraulic threaded cartridge valve this time. After several rounds of emails, we know the story for this hydraulic threaded cartridge valve. Their company has only begun to purchase hydraulic valves from China in recent 3 years. For the hydraulic threaded cartridge valves purchased at the beginning, there are always complaints from customers after a period of time, such as leakage or jamming, insensitive opening and closing or serious wear and tear, etc. In the past 2 years, Walt also tried samples from more than 20 hydraulic valve manufacturers. The same problems still occur after each replacement. Only AAK hydraulic threaded cartridge valves have not received a complaint. Walt compared more than 20 suppliers for 2 years, and only AAK hydraulic threaded cartridge valves had no complaints. This time, he strongly suggested his owner that the future hydraulic threaded cartridge valves can only be purchased from AAK. His owner also wants to know why AAK can ensure that there are no complaints about the hydraulic threaded cartridge valves. AAK hydraulic valve not only has the CNC machining center imported from Switzerland, but also has its own upgraded and refitted independent fixtures, which eliminates man-made errors. At the same time, we have accurately controlled every detail of the processing, production, assembly, inspection and packaging of each hydraulic threaded cartridge valve, which has surpassed the vast majority of domestic peers. Firstly, AAK will divide the installed products into several assembly units according to the structure and process characteristics of the hydraulic valve, reduce the single parts entering the general assembly as much as possible, and ensure the reasonable assembly sequence and specified assembly accuracy of the hydraulic valve. All parts will be accurately measured, strictly inspected and tested before and after the general assembly of the hydraulic threaded cartridge valve.

Erdmann has been a purchaser of German HAWE company for 5 or 6 years and has been doing very well. Last month, the company had a special hydraulic threaded cartridge valve to purchase. Because it is to be used in the Arctic region, the corrosion resistance of hydraulic threaded cartridge valve needs to be very high. The owner asked him to identify the suppliers and approve the samples within 2 months. Erdmann felt that it could be completed within 20 days. He sent the drawings of hydraulic threaded cartridge valves to the original hydraulic valve manufacturers. Only 2 weeks later, he received samples of hydraulic threaded cartridge valves from one factory. The surface gloss of these samples of hydraulic threaded cartridge valves was quite good. The company tested them on the exploration drilling machine and delivered it quickly to the customer. 3 months later, the customer complained that the hydraulic threaded cartridge valve on the hydraulic pump was seriously corroded, some threads were stuck, the equipment could not be started, and the test run was unsuccessful. The owner thought that Erdmann was careless and ignored the use scene of the Arctic region. The owner again asked him to make new samples and do salt spray test inside the company. Actually, Erdmann emphasized that the hydraulic threaded cartridge valve is to be used in the Arctic region. The original supplier said that their hydraulic threaded cartridge valves have good gloss and corrosion resistance, and can be used in the Arctic region. Erdmann communicated with the original hydraulic threaded cartridge valve supplier again, and the reply was that most hydraulic valve manufacturers just adopt the zinc plating process, and he used the nickel plating process which is the highest level of corrosion resistance. Erdmann realized the difficulty of corrosion resistance in the Arctic regions. Erdmann emailed more than 20 hydraulic valve manufacturers who had been contacted before, emphasizing that the hydraulic threaded cartridge valve must be in the highly corrosive environment in the Arctic region, and the service life shall not be less than 9 months. Only 3 hydraulic valve manufacturers said they could have a try, but there was no response from other manufacturers. Erdmann was a little flustered. Erdmann saw AAK hydraulic valve on Google, who supplied to hydraulic pump company in Russia. He felt that AAK might give him a glimmer of hope. He emailed us to ask if we can produce hydraulic threaded cartridge valves to be used in Arctic regions. We directly replied that the components of the valve should be treated by special electroplating process in order to meet the condition in the Arctic regions. After 20 days, AAK sent samples according to his hydraulic threaded cartridge valve drawings. HAWE company conducted salt spray test on samples from all 4 manufacturers, with the corrosion condition twice that of Arctic regions.

Zander is from a hydraulic manufacturing company in Greece. In the first half of this year, their company planned to upgrade the old logistics crane and put it back on the market. Its main goal is to improve its stability by 20% compared with its peers. The optimization of the hydraulic cartridge counterbalance valve is the key, but the original hydraulic cartridge counterbalance valve manufacturer has no ability to innovate. Zander found a local hydraulic cartridge valve manufacturer to optimize the structure and make samples. However, during commissioning, when the load of the system drops, the pressure fluctuation cannot exceed that of the peers, and the hydraulic cartridge counterbalance valve cannot avoid load interference. The local hydraulic cartridge valve manufacturer has no ability for further improvement. 2 months passed by, but there was still no solution. The boss pushed for progress many times, and Zander was worried. Zander found AAK on Google, noticed that AAK had released some customer cases about hydraulic cartridge counterbalance valves, and sent us an email. According to the schematic diagram of the hydraulic system and the original hydraulic cartridge counterbalance valve drawing provided by him, AAK engineer informed that the structure optimized by his local hydraulic cartridge valve manufacturer was not reasonable and needed to be adjusted. AAK has a trick to prevent the hydraulic cartridge counterbalance valve from being affected by the load. Zander asked for AAK samples. After 45 days, AAK sent 20 samples of hydraulic cartridge counterbalance valves. 3 months later, Zander sent an order for 500 hydraulic cartridge counterbalance valves, and told us that their technical department was very satisfied with AAK hydraulic cartridge counterbalance valves. Not only did they overcome the load impact, but also improved the stability of their new logistics crane by more than 20%. In the promotion stage, the booking was good, and the boss was happy. AAK hydraulic cartridge counterbalance valve can stably control the opening of the valve spool without being disturbed by the load, and its stability is higher than that of its peers, because we have tricks on optimizing the structure. AAK hydraulic cartridge counterbalance valve is composed of a valve body, a valve seat, a main valve spool, a pilot valve spool and a pilot mechanism. The valve seat is connected with the valve body and forms a connected first channel. The extended end of the valve seat butts against the pilot mechanism and forms a second channel. The main valve spool is provided with a throttling slot. One end of the pilot valve spool slides and is arranged in the inner cavity of the main valve spool. The other end is connected with the pilot mechanism. The pilot valve spool is equipped with a throttling slot. The pilot valve spool is connected with the inner cavity of the main valve spool as a balanced structure.

AAK 3 Skills Solved the problem of Hydraulic Counterbalance Cartridge Valve Caused by Back Pressure and helped Dorian's Equipment to be Promoted Smoothly Dorian is from a Greek hydraulic equipment company and is responsible for the procurement of hydraulic components. At the beginning of the year, they developed a new hydraulic crane, which requires the use of hydraulic counterbalance cartridge valve. Dorian worked with a local manufacturer to make samples. During the equipment commissioning, it was found that the hydraulic counterbalance cartridge valve had no overflow function due to the back pressure. The hydraulic system was tested separately, but it was normal. Dorian felt that there was a hidden danger in the original design of the hydraulic counterbalance cartridge valve. The engineer thought that the function of the hydraulic counterbalance cartridge valve was not up to standard. Dorian was a little embarrassed. Dorian found website of AAK hydraulic valves on Google, and noticed that AAK had been supplying first-line brand hydraulic valves such as HydraForce, SUN Hydraulics, and HAWE for many years. Maybe he saw hope and sent an email to ask for help. According to what he said, the hydraulic counterbalance cartridge valve has no overflow function under the influence of the back pressure of the closed central circuit. I told him that it was probably a flaw in the design of the original hydraulic counterbalance cartridge valve. According to his hydraulic schematic diagram and original drawing of hydraulic counterbalance cartridge valve, AAK engineer not only determined that the problem was in the original design, but also had a solution. After knowing these, Dorian asked AAK to make samples. After 50 days, AAK sent 10 hydraulic counterbalance cartridge valve samples. 4 weeks after AAK hydraulic counterbalance cartridge valve samples were sent, Dorian told me that the equipment debugging was smooth and the market promotion had been started. I was asked to wait patiently for the batch order. The rapidity and stability of AAK optimized hydraulic counterbalance cartridge valve is the key to smooth equipment commissioning. It solves the contradiction between the rapid response and stability of the equipment in the early stage, and the flow change is moderate, the movement is stable, the safety overflow function is not affected by the back pressure, which can be applied to the closed center and open center hydraulic systems. 1. The middle section of the hydraulic counterbalance cartridge valve spool is provided with an inner concave ring, which is also the valve inlet. The right end of the inner concave ring has a cone, on which there is a two-stage stepped taper ring. The cumulative area of the cone is the same as the area of the cylinder end face at the right end of the counterbalance cartridge valve spool.

Bauer is a purchaser of American PowerTeam company. In recent years, the purchasing of hydraulic valves has been smooth. Last October, PowerTeam received a test order for a hydraulic power unit from a South African customer. The customer requires to receive the prototype in the shortest time. If the prototype test is normal, there will be a series of orders later. The boss attached great importance to it and asked the technical team to design and develop it. What the engineers are most worried about is that the use frequency of the hydraulic power unit is twice that of the conventional one. Therefore, the durability of the hydraulic threaded cartridge valve used should be at least more than 2 million times. According to the parameters and working conditions of the hydraulic threaded cartridge valve, Bauer contacted more than 20 new and old hydraulic valve manufacturers. After one-to-one communication, he selected 5 hydraulic valve manufacturers to make samples for testing. 20 days later, Bauer received 6 samples of hydraulic threaded cartridge valves. After the engineers installed and tested, none of the hydraulic threaded cartridge valves could pass the durability test for 2 million times. Bauer had a second round of communication with the manufacturers, 3 of the hydraulic valve manufacturers said they would re-sample the hydraulic threaded cartridge valve. After the second round of testing, although the durability of hydraulic threaded cartridge valves has been improved, they have not reached 2 million times. Bauer was embarrassed. He might have killed the big order. After communicating, the manufacturer advised that there was nothing he could do. Bauer was very worried and had to try his luck with a new hydraulic valve manufacturer. He found AAK hydraulic valve on Google and searched AAK. After browsing, Bauer thought that AAK might be able to successfully sample this hydraulic threaded cartridge valve. After receiving the working condition requirements and drawings of the hydraulic threaded cartridge valve from Bauer, AAK engineer made analysis and determined that they were more than 95% confident to make it successfully. After 2 rounds of testing, the engineer defined the production process of proofing and circled the technical difficulties. After 20 days, AAK sent the samples of the hydraulic threaded cartridge valve. Unexpectedly, 2 months after the samples of hydraulic threaded cartridge valves were sent, we received the official order of 600 hydraulic threaded cartridge valves from Bauer. Bauer said that the equipment commissioning of South African customer was successful and the operation was stable, they were very satisfied with the quality of PowerTeam. The owner was very satisfied that Bauer found such a great hydraulic valve manufacturer and designated AAK as their exclusive supplier of hydraulic threaded cartridge valves.

The opening and closing characteristics can reach 95% opening rate and 90% closing rate, the operating pressure swing is not greater than ± 0.1MPa, and the design service life is more than 1 million times. For this high precision, high stability and high durability 3-high hydraulic threaded cartridge valve, Jacob is surprised that the AAK hydraulic valve is successful in one-time sample, while most hydraulic valve manufacturers are not able to do at all. Jacob is a purchaser of Intermot company in Italy. The company has a newly developed hydraulic motor, which needs to use hydraulic threaded cartridge valve. This motor is a high-frequency operation and has strict requirements for various parameters, especially for the parameters of hydraulic threaded cartridge valve, which has 3 high requirements of high accuracy, high stability and high durability. The owner asked Jacob to complete the procurement of this batch of hydraulic threaded cartridge valves within 60 days. He selected 4 from the original hydraulic valve suppliers to make samples. After installation, it was found that the opening and closing characteristics of hydraulic threaded cartridge valves can only reach 90% opening rate and 85% closing rate, which is 5% lower than the parameter requirements. Even the operating pressure swing of some hydraulic threaded cartridge valves exceeds 0.2MPa. In the last step testing, only 2 or 3 samples can be intact after 1 million durability tests. If all three requirements should be reached at the same time, nearly none of the samples meet the standard. Due to the limitation of equipment, the original manufacturer said it was difficult to improve significantly. Jacob learned about AAK hydraulic valve under the introduction of its peers. After browsing AAK website (www.aakindustry. com), he felt that the AAK hydraulic threaded cartridge valve might help him. After receiving the parameter requirements and drawings of his hydraulic threaded cartridge valve, we found that the requirements of this hydraulic threaded cartridge valve are not simple, but our technical team needs to chew this hard bone and gave reply to Jacob that if it goes well, the samples of the hydraulic threaded cartridge valve can be sent within 20 days. On the contrary, it needs more time for proofing. Jacob hopes that AAK hydraulic threaded cartridge valve sample will be successful, which just meets the delivery time required by the owner. After 15 days, AAK sent the hydraulic threaded cartridge valve samples successfully. After installation and test by the engineer, all parameters of the hydraulic threaded cartridge valves are qualified and meet the 3 high requirements of high accuracy, high stability and high durability. After 25 days, the shipment of the hydraulic threaded cartridge valve was delivered as scheduled.

Early last month, I saw an email from Mark, the purchasing manager of hydraulic system of Caterpillar, an old friend of ours. The subject of the email is "I need help from AAK, I believe". After reading the email about hydraulic threaded cartridge valve, I understood Mark's embarrassment. A small less-known excavator designed by them at the beginning of this year was not smooth in the commissioning process, the response of the excavation part was slow and the power was not enough. After testing, the technical department found that the measured value of the maximum overflow pressure was lower than the specified value, so it was determined that there was a problem with the hydraulic threaded cartridge valve. Mark communicated with the original hydraulic valve supplier. The supplier mentioned that the hydraulic threaded cartridge valve was sampled according to their company's drawings, and all parameter tests were up to standard. The supplier told the fact. He then could only patiently communicate with the design department to see how to modify the hydraulic threaded cartridge valve design, but the design Department said that there was a problem with the installation of the technical team. The company's design and technology departments prevaricate with each other and Mark are caught in the middle, which is very embarrassing and time is also being wasted. If the owner is angry one day, it is estimated that all 3 parties will be criticized. AAK HYDRAULIC VALVE has always been Mark's most trusted supplier of hydraulic valves. I asked Mark to send us the original design drawings of the hydraulic threaded cartridge valve and the working condition requirements of existing equipment, as well as the problems and data encountered in commissioning. 3 days later, we replied to Mark that we have a new design scheme, and we are 90% sure that we can make the hydraulic threaded cartridge valve that meet the equipment requirements, but it will take 2-3 weeks. On the 3rd day after receiving our sample of the hydraulic threaded cartridge valve, Mark happily informed us that the technical department tested AAK hydraulic threaded cartridge valve, the equipment commissioning was smooth, and the reaction and power of the excavation part were normal. The technical department said that the large goods of this hydraulic threaded cartridge valve can only come from AAK, and other hydraulic valve manufacturers are unreliable. Caterpillar designers are also curious about how AAK HYDRAULIC VALVE redesigns this hydraulic threaded cartridge valve? AAK engineering team tried 30 times to design, sampling and make adjustment to find a breakthrough. A sealing ring groove is arranged between the oil replenishment outlet and the oil replenishment inlet of the oil replenishment valve seat of the hydraulic threaded cartridge valve.

3 Advantages of AAK hydraulic cartridge relief valve, , a hydraulic customer from Bolivia, failed to purchase hydraulic cartridge relief valves from for the first time. has purchased hydraulic components from local hydraulic cartridge valve manufacturers in Bolivia for 3 years. He heard from his peers that the cost performance of purchasing from is better than that of Bolivian hydraulic valve manufacturers, so he began his overseas procurement trip. A hydraulic cartridge relief valve with rated pressure exceeding 30MPa, and the fit clearance between valve body and valve spool is required to be 0.006~0.01mm. successively tried samples with 3 hydraulic cartridge relief valve manufacturers in 70 days. The hydraulic cartridge relief valve samples had either internal and external leakage, blocked oil circuit, or even stuck. 3 times of proofing failed, which made helpless and even suspected that he was misled by his domestic peers. Richard noticed AAK on the B2B website and saw some tweets and customer cases to solve the problems of hydraulic cartridge valves, especially some big brands such as HydraForce and SUN Hydraulics, are also loyal customers of AAK for many years. He seemed to see hope and left a message to us: How much MPa can the rated pressure of the hydraulic cartridge relief valve with a clearance of 0.006~0.01mm between the valve body and the valve spool be? When I saw this message, I subconsciously felt that he had stumbled in the accuracy when purchasing this hydraulic cartridge relief valve, and he was inexperienced in choosing the hydraulic cartridge valve manufacturer. According to the problems of his hydraulic cartridge relief valve samples, AAK technical team determined that the problem was caused by burrs inside the hydraulic cartridge relief valve. However, the specific problem still depends on the sample analysis. I suggested Richard making samples directly to see the manufacturing quality of AAK hydraulic relief valves. Maybe that will change his view on China hydraulic cartridge valve manufacturers. After 30 days, AAK sent 10 samples of hydraulic cartridge relief valve. 6 months later, Richard emailed us that AAK hydraulic cartridge relief valves did not have the problems of "internal and external leakage, or blockage of the oil path or stagnation" that occurred in other hydraulic cartridge valve manufacturers, which also strengthened his confidence in purchasing from China hydraulic cartridge valve manufacturers. How to effectively avoid burrs of hydraulic cartridge relief valves? It is also a "thorn" that AAK has to remove since it was engaged in the R&D and manufacturing of hydraulic components. With 13 years of manufacturing experience, AAK can be sensitive to find problems and solve them. In the processing of hydraulic cartridge relief valves,

This Monday, Arthur sent an email to purchase 1,600 hydraulic threaded cartridge valves at one time, which was a little unexpected. Arthur came from a hydraulic equipment manufacturing company in Italy. He met with us at the PTC exhibition in Shanghai 3 years ago. At that time, he communicated with us for about half an hour. Then there were several inquiries for hydraulic threaded cartridge valves and several trial orders for hydraulic threaded cartridge valves. Last October, he suddenly sent an email saying that he had a client in Ningbo who wanted to visit AAK hydraulic valve factory. We introduced in detail a series of production links from raw material inspection and warehousing to rough machining, finishing, process inspection, assembly of valve body and spool, testing, packaging, warehousing, marking and shipping of each part of hydraulic threaded cartridge valve. After the visit, Arthur's client said they were satisfied with the scale, equipment and management of AAK factory and left. I wondered if this was really Arthur's client. More than a month later after visiting the factory, Arthur said that his company has developed a new hydraulic equipment, which requires high-precision hydraulic threaded cartridge valve. AAK needs to quote and make samples for testing as before. AAK sent 16 samples of hydraulic threaded cartridge valves after 30 days. I still think that this one will be the same as that one year ago, no big waves. I didn't understand that I made the mistake of "I thought" until receiving the large order of 1,600 hydraulic threaded cartridge valves yesterday. Today, I learned by email that it was not his client who came to visit the factory last year, but his assistant who often stayed in China. Before the company developed this hydraulic equipment, his assistant ran to more than 30 hydraulic valve manufacturers in China, especially for this special hydraulic threaded cartridge valve. AAK hydraulic valve has its own advantages in equipment and extension of equipment and on-site detail management. In particular, the component testing room of AAK is constant temperature and humidity for 24 hours, which is very helpful for hydraulic threaded cartridge valves with high precision requirements. Because of the particularity of this hydraulic threaded cartridge valve, the accuracy inspection of each component should be completed in a specific environment. Some quality problems of the products of many hydraulic valve manufacturers are just due to the deviation of the test results caused by the instability of the test environment. In the view of many factories, this may be a small detail, but AAK has done extremely rigorous testing. His assistant has not found a second one in Ningbo who pays so much attention to detail. That's why Arthur chose AAK to produce this big order of hydraulic threaded cartridge valve.

When back from the Spring Festival, we received a reorder for 120 hydraulic threaded cartridge valves from Echerle company. Dean has been engaged in hydraulic parts purchasing in Echerle company for many years, and has been doing very well. The boss also trusts him. At the beginning of last year, the company developed a new hydraulic power unit, which has high requirements for the accuracy of the hydraulic threaded cartridge valve to be used. Because of the high accuracy requirement, the original hydraulic threaded cartridge valve manufacturer said that he was not able to achieve it. Dean used a new hydraulic threaded cartridge valve manufacturer finally. After their hydraulic power unit equipment has been sold for just less than 3 months, the customer complained about insufficient power supply. Their engineers believe that the hydraulic threaded cartridge valve was stuck and caused the problem. However, the hydraulic threaded cartridge valve manufacturer believes that it is caused by the uncleanness of hydraulic oil, but the engineer detected that the hydraulic oil is normal. The owner was not satisfied with such a hydraulic threaded cartridge valve manufacturer and asked dean to find a new hydraulic valve manufacturer and replenish goods as soon as possible. Dean left a message on AAK website and asked, what are the reasons for the stuck of the hydraulic threaded cartridge valve? We estimated that he had encountered the complaint about the stuck of hydraulic threaded cartridge valve. After communication, we learned that he was cheated by the new hydraulic valve manufacturer. According to the hydraulic threaded cartridge valve drawings sent by him, the accuracy requirements are high, especially the dimensional accuracy requirement of the valve hole is IT7 ~ 4. Among the hydraulic valve manufacturers in Ningbo, there may be no more than 3 factories that are able to meet it. We suggested Dean send the abnormal hydraulic threaded cartridge valve to us. After receiving and disassembling the sample, it was found that the cylindricity and coaxiality of the valve hole of the hydraulic threaded cartridge valve had errors, that is, the accuracy was not enough, the pressure in the matching gap between the valve hole and the valve spool is not balanced, resulting in the limited flexibility and easy stagnation of the valve spool in the valve body. Dean asked whether we can produce hydraulic threaded cartridge valves meeting valve hole accuracy requirements of IT7 ~ 4? We told Dean that for the hydraulic threaded cartridge valve, the valve hole accuracy is the key point and also the difficulty of quality control process. It directly affects the working performance, service life and stability of the hydraulic threaded cartridge valve. General hydraulic valve manufacturers surrender to this accuracy. AAK has a precision honing machine imported from the United States, which guarantees the finishing of the valve hole of the hydraulic thread cartridg

Type: Valves Model Number: YF10-16 Brand Name: Longli Place of Origin: Shandong, China (Mainland) Product name: YF10-16 hydraulic poppet type pressure relief cartridge valve Max.Flow: 60L/min Certificate: ISO9001 Max Pressure: 350bar Material: Stainless Steel Place of origin: Shandong, China(mainland) Package: Neutral package Application: Machinery Color: customers' request Standard or nonstandard: Customized