Ld 9121 series temperature and humidity data logger has internal high-precision sensors for temperature or temperature and humidity measurements. There is no need to install any software to automatically generate a pdf report. The device stores maximum 16000 measuring data automatically with selectable sampling intervals from 1s to 24h. It is equipped with intelligent data analysis and management software for data download, graph checking and analysis, etc. This device is designed with lcd, led indicators and buttons. Real-time readings and alarm information can be displayed on lcd. The two leds flash in red, green and yellow colors to indicate the status of working and alarming. Its easy to operate with the two buttons to check data, start logging and clear data.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Measurement Temperature Range:-50 ,100 (-58F,212F) Humidity Range:0 - 100% RH Measurement Temperature Range:-50 ,100 (-58F,212F) Humidity Range:0 - 100% RH Accuracy : Temperature:0.3 (32.54F) Humidity : 3% RH Power Supply: Power : AC220V Power Consumption: : ¡Â1VA Environment Work Condition : :-20,65 (-4F,149¨¬F) Storage Condition: : -40,85 (-40F,185¨¬F) Resolution Accuracy:0.1/0.1%RH Communication:RS485 MODBUS RTU Display : Programmable 1 Line LED Switch Display Memory Capacity: Up to 20000 data points Data Sampling Interval:1s to 9 h (user selectable) Safe Protection : : Voltage Tolerance : Input & Power Supply >2 KV Input & Output > 2 KV Power Supply & Output >1 KV insulation : >5 M¥Ø. SIZE: 89X1.89X3.15 inch G.W/N.W: 500g/400g per piece Dimensions: 48X48X80 mm.
Focus-6500 butyl tapes has good performance in waterproofing and sealing, non-hardening, weather resistance, strong adhesion, adaptation and anti-aging . Technical Data Product Series FOCUS-6500 Series Application Home Decoration Industry Elongation 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 22N/cm Tensile Strength 210KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet Advantages Smooth and Delicate. Excellent Adaptation. Greene nvironmental protection. Non-toxic tasteless. Good performance in waterproofing and sealing. Best quality with outstanding service life. Applications Focus-6500 butyl tapes are widely used in bathrooms, kitchen, home decorations, office areas and other home applications, for its good waterproof/mildew proof /airtight and environmental property.
butyl tapes are waterproof and insulated tapes Focus-6400 butyl tapes are waterproof and insulated tapes with strong adhesion and adaptation to irregular surfaces. It exhibits excellent performance in waterproof, sealing and anti-UV to antenna feeder and cable connection box. Main Specification (Customized size is acceptable.) 2mm*40mm*20m * 8.5mm * 8mm * 10mm * 12mm Main Color - Black Technical Data Product Series FOCUS-6400 Series Application Communication Industry Elongation 400% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Tensile Strength 175KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet. Advantages Strong adhesion and adaptation to irregular surface. Good compatibility with various cables. Wide application temperature range. Excellent performance in weather resistance, waterproof sealing and anti-aging. Applications Provide waterproof and sealing protection to communication base station and antenna feeder. Provide waterproof and sealing protection to cable connection box
Butyl Tapes Are Waterproof And Insulated Tapes Focus-6400 butyl tapes are waterproof and insulated tapes with strong adhesion and adaptation to irregular surfaces. It exhibits excellent performance in waterproof, sealing and anti-UV to antenna feeder and cable connection box. Main Specification (Customized size is acceptable.) 2mm*40mm*20m * 8.5mm * 8mm * 10mm * 12mm Main Color - Black Technical Data Product Series FOCUS-6400 Series Application Communication Industry Elongation - 400% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility Â40, no crack on surface within 24h Tensile Strength 175KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet. Advantages Strong adhesion and adaptation to irregular surface. Good compatibility with various cables. Wide application temperature range. Excellent performance in weather resistance, waterproof sealing and anti-aging. pplications Provide waterproof and sealing protection to communication base station and antenna feeder. Provide waterproof and sealing protection to cable connection box
Adopting unique production technology, Focus- 6300 buytl tapes are mainly made of butyl rubber supplemented by other auxiliaries and fillers, with the superior high polymer materials. With its strong adhesion property and air-tight property, our waterproof sealing butyl tapes are environmental and solvent-free. Main Specification (Customized demand sare acceptable.) 6mm*8m 8mm*6m 10mm*4.57m Main Color - black Technical Data Product Series FOCUS-6300 Series Application Automotive Industry Elongation 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 23N/cm Tensile Strength 230KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanized sheet, aluminum sheet and coppersheet. Advantages Strong adhesion, high tensile strength, excellent elasticity and extensibility. It can fully accommodate to the surface that it attached to Excellent performance in non-corrosive, weather resistance and adaptation. Applications Provide waterproof protection to car doors waterproof membrane. Provide waterproof and sealing protection to the battery of new energy automobile. Other waterproof applications on cars and new energy cars
Focus-6200 products are kind of non-hardening and self-adhesive waterproof sealing butyl tapes. The materials are weathering resistance and fully accommodate to the surface that it attached to, with effective life up to 20 years. Main Specification (Customized size is acceptable.) 2mm thickness * 20mm width * 20mm roll length 2mm thickness * 30mm width *20mm roll length Main Color - black, grey, white Technical Data Product Series FOCUS-6200 Series Application Construction Industry Elongation - 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 25N/cm Tensile Strength 250KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet Advantages * Never hardening, maintain good waterproofing property with weathering resistance performance. * Excellent performance in waterproofing and sealing. * Good anti-aging performance effective life up to 20years. * Easy to apply. Applications * Provide waterproof and sealing protection forsteel structure construction. * Provide waterproof and sealing protection for door joints, window joints,roofs and air-ducts. Provide waterproof and sealing protection for sunshine rooms, light plate rooms and thermostatic chamber. * Provide repair function for leaks on surfaces of metal/plastic/glass/concrete.
Focus-6100 butyl tapes are mainly made of butyl rubber with excellent performance in waterproofing and sealing. Main Specification (Customized size is acceptable.) 3.0mm thickness * 12mm width *15m roll length 2.5mm thickness * 8mm width * 15m roll length 2 mm thickness * 15mm width * 20m roll length 2.5 mm thickness * 8mm width * 20m roll length Main Color black, grey, white Technical Data Product Series FOCUS-6100 Application Composite Materials Industry Elongation 500% Heat Resistance 90, no flowing within 2h Low Temperature Flexibility 40, no crack on surface within 24h Peel Strength 23N/cm Tensile Strength 220KPa Anti UV non-hardening and no cracks within in 2000h Corrosivity Non-corrosive to galvanizedsheet, aluminum sheet and coppersheet. Advantages Strong adhesion. Wide application temperature range. Excellent performance in waterproofing and sealing. Applications * During the production of vacuum extraction process for wind mill blade, it has excellent sealing property between vacuum bags and molds. During the production of vacuum extraction processfor fiberglass, it has excellent sealing property between vacuum bags and molds. * During the production of vacuum extraction process for cabin cover, it has excellent sealing property between vacuum bags and molds. * As auxiliary materials, our Focus-6100 series are widely used in the production of wind mill blade, fiberglass, cabin cover, car tail bracket, automotive engine cover, yacht. * Our products have excellent sealing property between vacuum bags and mold during the vacuum extraction process.
2-Naphthol Basic information Chemical Properties Application Preparation Product Name: 2-Naphthol Synonyms: c.i.37500;c.i.azoiccouplingcomponent1;c.i.developer5;Developer A;Developer AMS;Developer BN;developera;developerams CAS: 135-19-3 MF: C10H8O MW: 144.17 EINECS: 205-182-7 Product Categories: Fluorescent;Naphthalene;pigments;alcohol;MICROCIDIN;Color Former & Related Compounds;Developer;Functional Materials;Intermediates;Aromatic Compounds;Alphabetical;Bioactive Small Molecules;Biochemicals and Reagents;Building Blocks;C9 to C20+;Cell Biology;Chemical Synthesis;Fluorescent Indicators and Probes;Fluorescent Probes;Labels;N;Organic Building Blocks;Oxygen Compounds;Particles and Stains;pH Sensitive Probes and Indicators;Phenols;Dyestuff Intermediates;Aromatics Mol File: 135-19-3.mol 2-Naphthol Chemical Properties Melting point 120-122 C(lit.) Boiling point 285-286 C(lit.) density 1,28 g/cm3 vapor density 4.97 (vs air) vapor pressure 10 mm Hg ( 145.5 C) refractive index 1.5762 (estimate) Fp 153 C storage temp. Refrigerator solubility methanol: soluble1g/10 mL, clear, colorless to light yellow pka 9.51(at 25C) form Powder, Crystals or Granules color White PH Range Non& uorescence (8.5) to blue & uorescence (9.5) Water Solubility 1 g/L (20 C) �»max 226nm, 265nm, 275nm, 286nm, 320nm, 331nm Merck 14,6384 BRN 742134 Stability: Stable. Combustible. Dust may form explosive mixture with air. Incompatible with strong oxidizing agents, phenol. Major Application Display device, semiconductors, photoimaging materials, inks, toner, chalk, security paper, molding materials, tin plating method, rubber, adhesive, leather, detergent, hair dyes, antimitotic drug, anticancer agent, antiinflammatory agent, treatment of acne vulgaris (pimples) and other dermal ailments (rashes, scratches, blemishes, hair loss), disorders InChIKey JWAZRIHNYRIHIV-UHFFFAOYSA-N CAS DataBase Reference 135-19-3(CAS DataBase Reference) NIST Chemistry Reference 2-Naphthalenol(135-19-3) EPA Substance Registry System 2-Naphthalenol (135-19-3) Safety Information Hazard Codes Xn,N Risk Statements 20/22-50 Safety Statements 24/25-61 RIDADR UN 3077 9/PG 3 WGK Germany 2 RTECS QL2975000 F 8 Autoignition Temperature 430 C TSCA Yes HazardClass 9 PackingGroup III HS Code 29071590 Hazardous Substances Data 135-19-3(Hazardous Substances Data) Toxicity LD50 orally in Rabbit: 1960 mg/kg LD50 dermal Rabbit > 10000 mg/kg 2-Naphthol Usage And Synthesis 2-Naphthol Preparation Products And Raw materials
Blue Jay Electronic provide temperature & humidity logger solution, build on our temp. & RH controller can control environment condition and record the temp. vibration. The time interval is set by programming can be from 1 second to 2 hours. Use EEPROM s which can store up to 40,000 measurements. This could be one measurement every 30 seconds for 11 days for example. The control function with completed FUZZY algorithm provides very precise of temperature & humidity monitor. FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature curve by automatically. Display unit can show environment temperature and humidity as per configure by user. The user also can adjust environment condition very easily. Function & Feature ·DIN(48X48mm) or panel mounting ·High measurement indication and control accuracy 0.5?? and 3% RH ·Heat/Cool control and PID control mode ·All settings except time maintained permanently in non-volatile memory until changed by user ·Built-in digital filter reduce interfere ·Self calibration technology, keep stabilization ·Two line LED display show the data Independent, prevent dazzle, highly visible display ·Simple 4-Button user interface ·Switching power supply and low consumption ·Use large capacity relay ·RS 485 interface, easy to get raw data
Blue Jay Electronic provide temperature & humidity logger solution, build on our temp. & RH controller can control environment condition and record the temp. vibration. The time interval is set by programming can be from 1 second to 2 hours. Use EEPROM s which can store up to 40,000 measurements. This could be one measurement every 30 seconds for 11 days for example. The control function with completed FUZZY algorithm provides very precise of temperature & humidity monitor. FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature curve by automatically. Display unit can show environment temperature and humidity as per configure by user. The user also can adjust environment condition very easily. Function & Feature DIN(48X48mm) or panel mounting High measurement indication and control accuracy 0.5â?? and 3% RH Heat/Cool control and PID control mode All settings except time maintained permanently in non-volatile memory until changed by user Built-in digital filter reduce interfere Self calibration technology, keep stabilization Two line LED display show the data Independent, prevent dazzle, highly visible display Simple 4-Button user interface Switching power supply and low consumption Use large capacity relay RS 485 interface, easy to get raw data
Storage Type : Normal Temperature Specification: Food hygiene and safety Manufacturer: 99 Gold Data Ingredients 100: % Wild Craft Sea Grapes Content: 100% seagrapes Instruction for use: Soak in water for 3-5 minutes Shelf Life: 12 months
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103
Smart Home Appliances Climate Control OOH Grey 11 International Ergonomic Design & Styling 11 Fins with 3 Heat Settings 1000W / 1500W / 2500W Adjustable Thermostat to Maintain Desired Room Temperature Triple Safety Features: Safety Dumping Switch to Safeguard against tilting Manually Reset Thermal Cut-out Auto Reset Thermal Cut-out; Noiseless Operations Power ON Indicator Caster Wheels for Easy Mobility Cord Winder Built in Handle Less suffocation as it doesn?t burn oxygen.
Smart Home Appliances Climate Control Oil Heaters OOH 11F Grey International Ergonomic Design & Styling 11 Fins with 3 Heat Settings 1000W / 1500W / 2500W Adjustable Thermostat to Maintain Desired Room Temperature Triple Safety Features: Safety Dumping Switch to Safeguard against tilting Manually Reset Thermal Cut-out Auto Reset Thermal Cut-out; Noiseless Operations Power ON Indicator Caster Wheels for Easy Mobility Cord Winder Built in Handle Less suffocation as it doesn?t burn oxygen. 400W PTC ceramic heating element with motor for faster heating
POM Regrind from zipper Teeth, industry lump, industry runner Definition of POM resin (polyformaldehyde resin): polyformaldehyde is a linear polymer without side chain, high density and high crystalline properties. According to different chemical structures in the molecular chain, there are two types of homoformaldehyde and copolymers. of both types of polyformaldehyde density, high crystallinity, melting point, but thermal stability, the treatment temperature range is narrow (about 10oC), slightly lower in acid and alkali stability; The density of formaldehyde, melting point, strength and copolymer is lower, but good thermal stability, not easy to decompose, wide range of treatment temperature (about 50oC), acid and alkali stability are good . Plastic has excellent all-round performance. Good physical, mechanical and chemical properties, especially with excellent friction resistance. It is commonly referred to as steel or strip, which is the general engineering plastic third. Suitable for reducing wear on parts, transmitters, chemicals, tools and other parts. One of the synthetic resins, also known as polyformaldehyde resin, POM resin and steel, etc. This is a kind of white or black plastic resin with high hardness, high steel and high wear resistance. Used for gears, bearings, auto parts, machine tools, tools, etc. MATERIAL: POM Regrind from zipper Teeth , industry lump, industry runner CATEGORY: POM TYPE: Regrind SPECIFICATION: from zipper Teeth , industry lump, industry runner,Qty per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
Technical Data Sheet Of Accoset-50 ALUMINA MORTAR (Test Certificate) General Properties A. Max service temperature - 1500 oC B. Maximum grain size - 0 - 1.5 mm C. Water required for mixing - 22 - 30% D. Setting - Airsetting E. Sintering Temp - 1550 oC Chemical Properties A. Al2O3 - 50.00% B. SiO2 - 31.00% c. Fe2O3 - 5.00% D. LOI - 7.00% Physical Properties A. Dry Density - kg / m3 B. CCS - 17 kg / cm2 after drying at 110C / 24 hr C. MOR - 20 kg / cm2 at 110 oC/ 24 hr 18 kg/cm2 at 800 C/ 3 hr Thermal Properties - A. Refractoriness ( Orton / C) - 31.5 orton cone/1699 oC Packaging - 25 - 50 kg bags Storage Life - 12 months Delivery State - Dry
