L-W1S1 Temperature And Humidity Data Logger

Blue Jay Electronic provide temperature & humidity logger
solution, build on our temp. & RH controller can control
environment condition and record the temp. vibration.
The time interval is set by programming can be from 1
second to 2 hours. Use EEPROM s which can store up to
40,000 measurements. This could be one measurement
every 30 seconds for 11 days for example.
The control function with completed FUZZY algorithm
provides very precise of temperature & humidity monitor. FUZZY algorithm control fan or heater to
maintain sensible & latent capacity follows temperature curve by automatically. Display unit can show
environment temperature and humidity as per configure by user. The user also can adjust environment
condition very easily.
Function & Feature
·DIN(48X48mm) or panel mounting
·High measurement indication and control accuracy 0.5?? and 3% RH
·Heat/Cool control and PID control mode
·All settings except time maintained permanently in non-volatile memory until changed by user
·Built-in digital filter reduce interfere
·Self calibration technology, keep stabilization
·Two line LED display show the data Independent, prevent dazzle, highly visible display
·Simple 4-Button user interface
·Switching power supply and low consumption
·Use large capacity relay
·RS 485 interface, easy to get raw data

Measurement Temperature Range:-50 ,100 (-58F,212F)
Humidity Range:0 - 100% RH
Measurement Temperature Range:-50 ,100 (-58F,212F)
Humidity Range:0 - 100% RH
Accuracy : Temperature:0.3 (32.54F)
Humidity : 3% RH
Power Supply: Power : AC220V
Power Consumption: : ¡Â1VA
Environment Work Condition : :-20,65 (-4F,149¨¬F)
Storage Condition: : -40,85 (-40F,185¨¬F)
Resolution Accuracy:0.1/0.1%RH
Communication:RS485 MODBUS RTU
Display : Programmable 1 Line LED Switch Display
Memory Capacity: Up to 20000 data points
Data Sampling Interval:1s to 9 h (user selectable)
Safe Protection : :
Voltage Tolerance : Input & Power Supply >2 KV
Input & Output > 2 KV
Power Supply & Output >1 KV
insulation : >5 M¥Ø.


SIZE: 89X1.89X3.15 inch
G.W/N.W: 500g/400g per piece
Dimensions: 48X48X80 mm.

Intelligent temperature & humidity controller with
completed FUZZY algorithm provides very precise
of temperature monitor. FUZZY algorithm control
fan or heater to maintain sensible & latent capacity
follows temperature/humidity curve by
automatically.
Display unit can show environment temperature
and humidity as per configure by user. The user
also can adjust environment condition very easily.
Function & Feature
·DIN(48X48mm) Controller
·Indication and control accuracy 0.1, high measurement
·Heat/Cool control and PID control mode
·All settings except time maintained permanently in non-volatile memory until changed by user
·Built-in digital filter reduce interfere
·Self calibration technology, keep stabilization
·LED display show the data, prevent dazzle, highly visible display
·Simple 4-Button user interface
·Switching power supply and low consumption.
·Use large capacity relay

Type Universal USB charger socket
Charging Port 2 Ports
Connection Universal USB charger socket
Warranty 1 Year
Combination Charger Socket Outlet
Voltage 12-24v
Model Number DS2014
Design Style New China-Chic
Product name 4.2A Car Cigarette Lighter Socket Splitter Dual USB Charger
Material ABS
Input Voltage 12V-24V
USB output 4.2A
Size 3.7*5.4*2.9cm/1.5*2.12*1.14inch
LED Blue LED
Waterproof grade IP65
Working temperature Min.-20 Celsius Degree, Max. 80 Celsius Degree

PE coil pipes and tubes for water and wire cable conduit PL231


The PE coil pipes and tubes can be used:

water pipe 4 â?? 6 â?? 1-inch black coil with pressure 1.6mpa, OD 20-75mm, WT 2.3-6.8mm
pe conduit cable embedded wire cable and optical cable, OD 20-200mm, WT 1.8-3.5mm
weak current protection tube and communication tube, OD 20-200mm, WT 1.8-3.5mm


We use new 100% pure raw PE material


WHY NEW MATERIAL HDPE PIPES?

1. Health performance

PE pipe processing without adding heavy metal salt stabilizer, no scaling layer, and no bacteria.

2. Corrosion resistance

It can resist various chemical media erosion, with no electrochemical corrosion.

3. Service life

Under rated temperature and pressure conditions, PE pipes can be used for more than 50 years.

4. Impact resistance

PE pipe toughness, high impact strength, heavy objects directly pressed through the pipeline will not break.

5. Connection performance

The strength of the hot melt or electric melt interface of the polyethylene HDPE pipe is higher than that of the pipe body, and the joint will not be broken due to soil movement or live load.

6. Construction performance

It has a lightweight pipe weight, a simple welding process, convenient construction, and a low overall project cost.

Temperature Logging System) is an advanced independent weather monitoring system. It supports Secure Digital card which is used to record the data for 10 years with 2GB SD card and with a LCD for on-line monitoring
Change in temperature at every time second is recorded
Auto sense with 10 years report
Solar powered
No external power supply required
Supports secure Digital card
Auto Data Save Algorithm used
Lcd Display for upto date temperature
Inbuilt RTC
Report with Date/Month/Year/Hr/Min/Sec
Suitable for any remote place
Temperature is calibrated in celsius
Led indication
On -off switch for recording.

XM452 Temperature Humidity Controller for Incubator With Indicators Thermometer Hygrometer Automatic
XM452 Temperature Humidity Controller for Incubator With Indicators Thermometer Hygrometer Automaticpower supply :DC 12V Temperature measurement range:- 40~120? Humidity range?0~100%RH Control precision?0.1? 0.1% RH Test probe?Integrated sensor output:10A delay Size:65*55*28mm
temperature control: 1. Set the temperature + ?Normal display mode, long press the + key for 3 seconds, start temperature numerical flashing, press the + / - key setting values, wrong operation after 5 seconds, automatically return to detect temperature display 2. Set the temperature ?- Normal display mode, long press - button for 3 seconds, stop numerical flashing temperature, press the + / - key set value 3. Restore the factory Settings:- At the same time long press temperature, and humidity
Set the start temperature:Long press the + key, start the flashing temperature, set start temperature by + / - key set Stop temperature:- long press - button, stop flashing temperature, set stop temperature by + / - key
Humidity Settings: Set to start humidity: long-press the + key, start the humidity value flashing, set by + / - key launch humidity value Set stop humidity:- long press - to stop humidity value, set by + / - key to stopping the humidity value Fault code:- display LLL means the sensor fault display HHH mean Test temperature exceeds the range of measurement