LC 122 is an effective wide band micro-biocide designed for use in algae and bacteria control. It does not cause foaming and is not lost by evaporation from the system. It is a concentrated blend of organo-sulfur compounds, which should be added only after proper dilution by slug feeding. Application: Use to control algae and bacteria in re-circulating commercial and industrial water cooling towers. Prior to its use, systems be cleaned to remove algae growth, microbiological slime and other deposits. Dosage: Initial slug additions of LC 122 per 1,000 gallons of water should be employed every 1 - 5 days or as needed. The frequency of addition depends upon the relative amount of bleed-off and the severity of the microbiological problem. Slug additions should be made in the sump of the cooling tower. During very hot weather, greater frequency or higher dosage may be required to increase its effectiveness. Handling & Precaution: It is a very strong alkaline treatment and may cause eye damage and skin irritation. Do not get in eyes, skin or on clothing. Wear goggles or face shield and rubber gloves when handling. Avoid contamination of food. Harmful or fatal if swallowed. In case of skin contact wash with plenty of soap and water. Remove contaminated clothing and wash before reuse. If product gets in the eyes, flush immediately with copious amount of clean cool water for at least 15 minutes. If swallowed, call physician. Do not induce vomiting or give anything by mouth to an unconscious person. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
LC 123 is specially formulated for large installations high hardness water. It is developed for effective, economical cooling water treatment at hospitals, hotels, large apartment houses, office buildings and other industrial and institutional cooling installations with high hardness make-up water. It contains no phosphates, chromate, zinc, or other chemicals that cause pollution problem. Helps control mineral deposits, sludge and surface pitting and does not stain automobiles or buildings. Application Use a reliable automatic proportioner with timer for controlled dosage. Follow instructions for calculated bleed of rate and recommended daily maintenance treatment as suggested by the Field Chemist Personnel. The dosage and treatment program depend on size of installation and water hardness (ppm). Dosage Initial treatment : Add 1 gallon of LC 123 per 2,000 gallons of recirculating water. Maintenance treatment as per size of installation & hardness (consult our Technician) Handling & Precaution Wear protective clothing and eye protection should be provided and worn. In case of skin contact, immediately flush thoroughly with plenty of clean water. In case of eye contact, flush with copious of amounts of water for 15 minutes and obtain immediate medical attention. Refer to MSDS for more specific directions. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 124 is an effective chlorine based designed for use in algae and bacteria control. It does not cause foaming. It is a concentrated blend of organo-chloro compounds which should be added only by slug feeding. Application: Use to control algae and bacteria in re-circulating commercial and industrial water cooling towers. Prior to its use, it is advisable that systems be cleaned to remove slime and other deposits. Dosage: An initial slug addition of 1 gallon of LC 124 per 2,000 gallons of water should be employed every 1-4 days or as needed. The frequency of addition depends upon the relative amount of bleed-off and the severity of the microbiological problem. Slug additions should be made in the sump of the cooling tower. During very hot weather, greater frequency or higher dosage may be required to increase its effectiveness. Handling & Precaution: It is a very strong treatment and may cause eye damage, mucous attack and skin irritation. Do not inhale, get in eyes, skin or on clothing. Wear goggles or face shield and rubber gloves when handling. Avoid contamination of food. Harmful or fatal if swallowed. In case of skin contact, wash with plenty of soap and water. Remove contaminated clothing and wash before reuse. If product gets in the eyes, flush immediately with copious amount of clean cool water for at least 15 minutes. If swallowed, call physician. Do not induce vomiting or give anything by mouth to an unconscious person. Packaging: Available in pail of 20 lt.. Can also becustom packaged.
LC 255 is a versatile and highly effective rust preventative for use on unpainted metals during outdoor storage or overseas shipping. LC 255 protects metal with heavy waxy film. It does not require any surface cleaning or preparation and covers the metal like a paint, but easily removable. LC 255 provides protection for storage of metal, equipment, tools, tanks, structures, machinery, castings, fittings, valves, doors, frames, fixtures, jigs, etc. Application: LC 255 can be applied by spraying, brushing or dipping. It is recommended to apply by dipping in a tank with water draining facilities which ensures maximum coverage, penetration and cost effectiveness. LC 255 absorbs water and moisture while lubricating plated surfaces and bare metals such as steel, iron, alumunium, copper, brass and lead. Handling & Precaution: Avoid contact with eyes and skin. In the case of contact with eyes, wash immediately with plenty of water. Seek medical advice. If ingested, do not induce vomiting, seek medical attention. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
KB 201 is a powerful porcelain cleaner for brightening & cleaning porcelain surfaces. It contains complexing agent, sequestering agent, scale remover, wetting agent and specialized blooming remover. It is a specialized product and requires careful application methods. WRONG & UNWANTED APPLICATIONS NOT PRESCRIBED, MAY CAUSE UNEXPECTED RESULTS & DAMAGE. Must be diluted before use. Never use on glazed surfaces. Application: Pour diluted KB 201 on the surface to be cleaned, allow it to react for 2 – 20 minutes, depending on the type of stain & dilution factor. After that, brush with soft brush then rinse thoroughly with clean water. Make small test spot to verify result before actual use. Dosage: Dilute with water depending on the cleaning work. Can be diluted up to 50 times or more. Handling & Precaution: Contains only organic acidic compounds. Do not ingest. Do not get in eyes, on skin or clothing. Keep the container closed when not in use. Avoid breathing the mists. Wear a mask when handling. Use sufficient ventilation to prevent build-up or mists. KEEP AWAY FROM CHILDREN. Packaging: Available in pail of 20 lt.. Can also be custom packaged.
KB 224 is a special water based polymer with silicone specially designed to protect and keep a shine & wet look on vinyl, rubber, plastic and leather or other such surface materials. KB 224 protect surfaces from fading and cracking by reducing ultraviolet light, while bringing out color, restoring luster and shine, protects against abrasion. Eliminates static electricity to reduce dirt attraction. If less shine is desired, lightly buff with damp cloth. Application: Apply KB 224 with a clean cloth or sponge ( or spray ) with a cleaning action. Spread evenly, allow to penetrate and chemically bond for a few minutes then remove excess for a beautiful protective shine. On some surfaces a two coat application provides best results. Apply as needed to maintain shine and protective coating. Dosage: Use undiluted product. Handling & Precaution: This product may caused slipperiness on certain surfaces until it is completely dry. May caused smearing on glass or other transparent services. Avoid spills on eyes. Should avoid prolonged unnecessary contact with skin. May irritate when exposed for a longer period on certain sensitive skin. Harmful if swallowed. Keep away from children. Keep container capped in a cool dry place Packaging: Available in pail of 20 lt.. Can also be custom packaged.
KB 273 is concentrated degreaser specially formulated to penetrate, emulsify and disperse oil, grease, dirt, soot and burnt / residual carbon from a variety of hard surfaces. Specially designed for use in ovens, grills, chimneys, exitways, smoke escapes, air vents where thick deposit of soot/carbon is common by found. Most effective for oily residues and its water base composition make easy flushing. Application: Allow soaking time ( 5 – 30 minutes ) for effectiveness. Apply a thin layer by spraying or brushing, then leave for soaking. Brush and scrap gently to remove any hard soils if required then flush with water. ( Use KB 212 for best results ) Protective measures is suggested for cleaning personnel Dosage: Dilute with ratio of 1 : 10 ( max. ) with water depending on the dirt thickness. Use concentrated product or lower dilution for tougher stains. Dilute up-to 50 times for regular cleaning work. Repeat if necessary Handling & Precaution: Avoid eye contact. Should avoid prolonged contact with skin. Harmful if swallowed. Use protective gloves where contact is in evitable Packaging: Available in pail of 20 lt.. Can also be custom packaged.
Catalyzed Oxygen Scavenger with polymers for preventing pitting. Ideal for use with both hard and presoftened make-up water. Application Can be injected directly into the boiler by means of a proportioning pump. Advisable to gradually feed LC 102 by means of a chemical proportioning pump into the storage section of the de-aerating heater as far ahead of the boiler as possible to provide maximum effectiveness in high pressure boiler operating from 100-600 psi. or where large amount of water is used. Dosage Initial : 3 quarts per 1,000 gallons or 3 : 4000 Maintenance: 1 quart for every 1,000 gallons of make-up water or 1 : 4000 Maintain 20-50 ppm (mg/l) in the boiler water. LC 102 can be used in conjunction with other formula in our product line, but should not be used in a boiler operating in excess of 600 psi. Handling & Precaution LC 102 is mildly acidic product and should be handled with care to prevent personal injury. Wear protective clothing and eye protection. In case of contact with skin, immediately flush with water. In case of contact with eye, flush with water for 15 minutes and obtain immediate medical attention. Packaging Available in pail of 20 lt.. Can also be custom packaged
LC 104 is an ideal single product boiler internal treatment, specially formulated by blending sludge conditioner & oxygen scavenger for dual function in packaged boiler systems. It can control not only calcium carbonate & calcium phosphate deposits but also calcium sulfate and barium sulfate. Highly concentrated alkaline product. Eliminates excessive precipitation of solids and reduces sludge accumulation. The oxygen scavenger prevents pitting corrosion in the boiler system. It is environmentally safe, non-hazardous and non-corrosive. Application Used in packaged boilers below 5 Tons/Hr. For use with make-up water hardness below 150 ppm and effectively disperses iron oxides as well as calcium phosphate and clay. Injected directly into the boiler by means of a proportioning pump. Dosage Initial : 2 quarts per 100 gallons or 1 : 200 ratio Maintenance: 1 quart for every 100 gallons of make-up water or 1 : 400 ratio Maintain 15-25 ppm (mg/l) of orthophosphate in the boiler waters with pH between 11.0 – 12.0. Maintain Conductivity below 3000 µmho/cm. Consult LifeChem Technical Services when Hardness is low or high. Handling & Precaution LC 104 is an alkaline product and should be handled with care to prevent personal injury. Wear protective clothing and eye protection. In case of contact with skin, immediately flush with water. In case of contact with eye, flush with water for 15 minutes and obtain immediate medical attention. Triple rinse used cans before reuse or disposal. Refer to MSDS for detailed information. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 200A is safe, phosphatic alumunium cleaner and brightener. It’s strong formula will dissolve any oxide layer and also has the added benefit of providing a protective phosphatic layer to keep aluminum surfaces looking at their best. The non-toxic formulation also prevents further oxidation of the surface and repels dust build up owing to its electrostatic effect. It has penetrating agents that clings to alumunium surfaces for maximum effective cleaning result. Application Use LC 200A undiluted for initial cleaning and brightening on tough or built-up soil problem. Use diluted product for regular cleaning. Determine dilution depending on contamination type & frequency of cleaning. For on-going maintenance use LC 301 for a protective and shiny coat. For maximum cleaning, apply LC 200A with a highpressure washer Dosage The dilution will vary, depending on the condition on the surface to be cleaned. For best result, rinse with a high-pressure washer or apply with a brush. For normal cleaning & brightening; apply LC 200A at a dilution up to 1:20 with water. Allow the solution to react with the surface for 1 – 3 minutes, and then rinse thoroughly with clean water through a pressure washer. Do not allow LC 200A to dry on the surface. Repeat application if necessary. Handling & Precaution Contains mild acid. Do not ingest. Do not get in eyes or clothing. Wear a face shield, neoprene rubber gloves & protective clothing if spattering is expected. Keep the container closed when not in use. Avoid breathing the mists if produced during application by spraying. Use sufficient ventilation to prevent build-up of mists during application. Packaging Available in pail of 20 lt. Can also be custom packaged.
Lc 270 is a water based general purpose cleaner to Penetrate, emulsify and disperse oil, grease, dirt and Grime and other types of soils from a variety of hard Surfaces. Ideal for cleaning walls, floors, desks, light Fixtures, automobiles, painted woodwork. Also can be Used on metal surfaces such as stainless steel, Aluminum, cooper and brass. Application Spray, mop, brush wipe, dip method are recommended. Use for Cleaning walls, floors, desks, light fixtures, automobile, painted Wood work. Dosage Dilute with ratio of 1 : 10 with water depending on the dirt Thickness Handling & precaution Avoid spills on eyes. Should avoid unnecessary contact with Skin. Can irritate when exposed for a longer period. Harmful if Swallowed. Packaging Available in pail of 20 lt. Can also be custom packaged.
Lc 300 is a designed specifically for stains on granite Surfaces arising out of contamination during production Or due to storage. It is very effective for stains on granite Surfaces due to poor quality water, inproper storage & Soil contamination. It is an acid based special blend of Selected penetrants, emulsifiers, dispersant & solvent Carriers designed to effectively penetrate, react, dissolve & remove the stains from the surfaces as well as deeper Into the granite structure without affecting the surface. Application Make sure that the granite surfaces are free from dust, soil & dirt. Apply lc 300 on The pre-treated surface by brushing to leave a thin uniform film on the whole Surface. Do not leave any surface untreated. Wait until 15-30 minutes or more until The stains start dispersing. Rinse and wipe clean the whole surface with demin Water. For deeper & thicker stains, repeat the process. May not be suitable for Certain types of granite & marble. Always make a test sample before final Application. Handling & precaution Avoid contact with eyes, skin and clothing. In case of contact, immediately wash With plenty of water. Harmful if swallowed. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Multi type glass cleaner
Kb 208 can be used to remove stains from hard surfaces Including metallic and non-metallic surfaces like glass, ceramic, Melamine, etc. The key to an effective cleaning depend on proper Dilution & soaking time. It’s food-grade quality allows its use in Places where cleaned surfaces may have direct contact with food. Kb 208 is designed specially for use in places where the use of Acidic products are not recommended. It’s strong disinfectant Function kills most common microbes & disease causing bacteria. Application Kb 208 must be diluted with water for soaking, dipping etc. May also be used by Brushing & scrapping. Dilution depend on soak time, for faster action use lower Dilution ratio that is higher concentration. May be diluted up to 500 times or more. It Has disinfectant function. Dosage Add about 100 gm/100 ml of kb 208 to about 100 lt. Of water or as required for Soaking and dipping. Use higher concentration for faster action and tougher stains. Agitation gives better result. Re-use solution until turbidity is high. Required to Repeat the process if necessary. When the cleaning process is complete, flush with Clean water. Use concentrated product for manual cleaning Handling & precaution This product is alkaline and should be handled with care to prevent personal injury. Avoid prolonged skin contact and breathing of the fumes. Refer to material safety Data sheet for more specific procedures and directions. Discoloration may Result when contact with colored clothing. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Cleaning vinyl surfaces from dirt, grease, oil, and dust. Suitable for carpet cleaning vinyl flooring and other vinyl surfaces. Safe to use on metal surfaces such as stainless steelm aluminum, copper, brass.
Clean the floor with a perfect and refreshing fragrance.
Kb 217 is a special water based carpet cleaner to Penetrate, emulsify and disperse oil, grease, dirt and stains on Fibers of synthetic carpets. Ideal for cleaning synthetic carpets Normally used on floors of office buildings, hotels, hospitals & Other public places. This formulation does no have any adverse Effect on painted surfaces including walls, wood and also metals Like stainless steel, aluminum, copper and brass. The room is Filled with a refreshing fragrance from kb 217 after the cleaning Work. Application Use diluted kb 217 ( 1 : 5 up to 1 : 20 with clean water ) with standard carpet Cleaning equipment like mopping machine & wet vacuum cleaner. Apply & spread The solution of kb 217 to the carpet surface and allow a soaking time of 2 – 10 Minutes before scrubbing rinsing & final mopping. The wet carpet should be Properly mopped with standard equipment & procedure until dry. Always make a test patch to confirm color fastness & soaking Time. Kb 217 can also be filled in directly into the detergent container provided with Certain carpet cleaning equipment which has a facility for it. Dosage Dilute with water depending on the cleaning work & stain. Can be diluted up to 20 Times. Direct applications of the undiluted product may be required on highly Stained areas Handling & precaution Avoid spills on eyes. Should avoid prolonged unnecessary contact with skin. May Irritate when exposed for a longer period on certain sensitive skin. Harmful if Swallowed. Keep away from children. Keep container capped in a cool dry place Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 120 is a product which effectively prevents scale and Corrosion in cooling towers having very soft waters which Are more corrosive, have a rysnar index over 7 and Calcium 25 – 75 ppm in the make-up water. It is an Excellent dispersant for calcium phosphate, iron oxides And clay. This product is used where heavy metals and Zinc is not allowed in effluent waters. Lc 120 is a Hydroxy-phosphonoacetic acid with polymers and copolymers To control scaling. It also has inorganic Phosphate and sodium tolytriazole to prevent corrosion And pitting of all metal surfaces. Application Injected directly into the circulating pipe upstream from the condenser. Cycles of concentration will vary from 5 – 20 as a probable upper limit. For Higher limits consult our laboratory. Dosage Feed lc 120 from a chemical mix tank or directly from the drum by means Of a proportioning pump at the rate of 0.5 pound / 1, 000 gallons of make-up Water. Adjust the dosage to maintain 5 – 10 ppm of orthophosphate in the Circulating water. A ph of 8.0 – 8.5 must be maintained. Handling & precaution Protective clothing and eye protection should be worn. In case of skin Contact, immediately flush thoroughly with plenty of clean water. In case of Eye contact, flush with copious of amounts of water for 15 minutes and Obtain immediate medical attention. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Lc 238 is designed specially for use in systems where the use Of concentrated acidic or concentrated alkaline descalers are Not recommended. This product is specially formulated for Specific cleaning and descaling purposes for sensitive system. Lc 238 may be re-circulated by means of a high volume pump For the removal of scale. Lc 238 can be used safely on to Copper & brass surfaces besides being very effective in steel System. This product contains organic poly acrylic & polymer Compound. Application Lc 238 may be soaked overnight and re-circulated. When scale is Present, the tubes should first scraped out to remove as much as possible And then flushed out with a hose. Dosage Circulate an appropriate concentrated solution based on the scale and Corrosion. For storing / stand by system use lc 253 or lc 252. For more Detail and specific method and concentration, please consult lifechem Technical services. Handling & precaution This product ph is between 4.0 – 9.0 and should be handled with care to Prevent personal injury. Protective clothing, gloves and eye protection Should be worn. In case of skin contact, immediately flush thoroughly with Plenty of clean water. In case of eye contact, flush with copious amounts Of water for 15 minutes and consult a physician. Refer to material safety Data sheet for more specific procedures and directions. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Lc 239 is a very strong descaler for destroying the most Difficult scales. It effectively removes difficult scales, rust, Oxides of metals, silica scale and hard soil from metal and Other surfaces. It’s dissolving action is quick and thorough. Most cost effective descaler when combined with lc 230, Lc 233, lc 232 and lc 231. Do not use on materials like Glazed tiles and glass. Must be used after dilution only. Application Dilute and blend with other descalers as necessary before dipping, brushing or Spraying on surfaces. Clean surface free from excess rust, soil and dirt. Apply lc 239. Allow to stand for 10-20 minutes, then flush off with water. Surface may Require repainting if necessary. Recommended to use lc 240 for neutralization And lc 252 for passivating the native surface on ferrous metals. Avoid contact With unwanted surfaces. Dosage For descaling purposes, dilute one part lc 239 with up to 20-100 parts of water Depending on the type and thickness of scale and method of application. Allow to Stand / circulate for several hours or as necessary. Flush with water until all the Scale is removed. Repeat if scale is still present, check ph during application for Control. Contact field chemist for further information. Do not use above 2% with Non-chemical pumps for circulation Handling & precaution Strongly acidic. Irritating to eyes and skin. After contact with skin wash Immediately with plenty of water. In case of eye contact irrigate thoroughly with Water for at least 15 minutes. Seek medical advice. Avoid direct contact with Glass, tiles and other such surfaces. Use adequate protective measures during Use. Packaging Available in pail of 20 lt. Can also be custom packaged.
