The most Economic and Practical Ultra-fine Powder Processing Equipment, the Energy-saving and Reduce Consumption Equipment fro ultra fine Powder Processing HCH ultra-fine grinding mill is especially suitable for ultra fine grinding. With yearsâ?? accumulation of experience in R&D, the HCH Ultra-fine Grinding Mill is a new ultra fine pulverizing equipment designed by Hongcheng. This mill is widely used to grind any non-metal minerals with Moh's hardness below 7 and moisture below 6%, such as talc, calcite, calciumcarbonate, dolomite, bentonite, kaolin, graphite, carbon black, etc. HCH Ultra-fine Grinding Mill features in space-saving, completeness, wide usage, easy operation, smooth performance, high performance-cost ratio and high efficiency. HCH1395 Grinding Mill is the biggest ultra fine circle-roll grinding mill in China. Working Principle Technological process: The pre-grinding raw ore material will be crushed into particlesï¼?10mm and transport to the feeding hopper by the elevator, then feed into the grinding chamber by the feeder. The grinding rollers equip on the rotary table rotates around the centre shaft. There is flexible gap between the roller and ring. The rollers rotate outward by the centrifugal function to compress the fixed ring. The rollers also self- rotates around the roller pin. When material passed through the gap between the ring and roller, the material will be smashed by the rotating rollers. Four layers of rollers. Material will be grinded 1st time when passing the 1st layer of roller and ring. Then be grinded second, third and fourth time when loop through each layer rollers. Thus the materials were grinded sufficient and obtain much fine powder. The powder fallen down onto the bottom table by gravity will goes up to the classifier for separation by the airflow from blower. The qualified fineness passing from the classifier will be collected by the pulse bag collector as final product, while unqualified fallen down for regrinding till passing through. The powder goes with air flow into the pulse bag filter and collects by the discharging valve. The wind path is in circulation and the airflow is in negative pressure. There will be no dust escape, so the equipment can ensure a no dust operation in workshop. Application Range HCH Ultra-fine Grinding Mill is widely used to grind any non-metallic minerals with Mohs hardness below 7 and moisture below 6%, such as talc, calcite, calcium carbonate, dolomite, bentonite, kaolin, graphite, carbon black etc.. This kind of mill is especially suitable for ultra fine grinding. The fineness can be adjusted from 0.045mm(325 mesh) to 0.005mm(2500 mesh), whose range is much wider than that of traditional Raymond Mill.
Description Rock hammer crusher can crush ore which is below 50mm or the tailings, middlings which in the uncompleted ore. And break up the useful metal from the ore, depending on the requirement of factory, it can crush the mineral particles in 1 to 180 mesh, and separate them in the shaking table. They are suitable for the small factory, and same times can take place of ball mill in some degree, Easy installation, easy operation, less investment, fast effect. The rock hammer crusher consist of rotor which with hammer, and the rotor consist of spindle, disk, pin and hammer. The motor drives the rotor to rotate at a high speed through the belt, the material enter the machine through the feeding port the rotating hammers with high rotation speed are crushing them, the small size mineral was discharge through the sieve and the large size still was crush and beat in the sieve until the crushed products meeting the required size can be discharged by the outlet and become the final products. Main Technical Parameters Model Capacity (T/h) Feeding Size (mm) Discharge Size (mm) Power at user option Motor (Kw) Diesel 200Ã?500 1-2 â?¤50 â?¤1.8 15-18 24 300Ã?500 3-6 â?¤50 â?¤1.8 18-22 30 400Ã?600 5-10 â?¤50 â?¤1.8 25-30 45 Rock Hammer Crusher
Description The ball mill is a key equipment to grind the crushed materials, and the ball mill is widely used in powder-making production line including cement, silicate, new-type building material, refractory material, fertilizer, ore dressing of ferrous metal and non-ferrous metal, glass ceramics, etc. According to discharge in different ways, the ball mill can be divided into gate ball mill and overflow ball mill. The gate ball mill is enforced discharging, relatively the discharge would be coarser, but the capacity would be higher, usually the gate ball mill used for primary grinding, the overflow ball mill used for secondary grinding. The ball mill is a horizontal rotating device transmitted by the outer gear. The materials are transferred to the grinding chamber through the quill shaft uniformly. There are ladder liner and ripple liner and different specifications of steel balls in the chamber. The centrifugal force caused by rotation of barrel brings the steel balls to a certain height and impact and grind the materials. The ground materials are discharged through the discharging board thus the grinding process is finished.
Description Jaw crusher has the features of great crushing ratio, uniform size of products, it mainly used to crush kinds of mining stones primarily, it can be used to crush material its compressive resistance not more than 320MPa. The jaw crusher is widely used in mining, metallurgical industry, building material, highway, railway, and chemical industry. The motor transmits power through belt, drives the moving jaw do periodic motion to the fixed jaw surround the eccentric shaft. The angle between toggle plate and moving jaw increases when moving jaw moves up. So the moving jaw closes to the fixed jaw. The stuff will be crushed in this process. The angle of Jaw Crusher between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw of Jaw Crusher moves away from fixed jaw by the pulling of rod and spring, the products after crushing will be discharged from the outlet of Jaw Crusher. Advantages and Characteristics 1 Simple structure, easy operation and maintenance, the downtime is greatly reduced; 2 Moveable jaw assembly adopts high quality casting steel, heavy eccentric shaft adopts forging steel processing, the machine with transcendental stability; 3 Adopt more durable eccentric shaft bearing, so the bearing capacity is big.
The crushing effect is good, good sealing performance, no adhesion or blocking material, with clean, widely used in various industries crushing sample preparation work.
Main features: 1, suitable for crushing hard or brittle materials; 2, continuous error reduction, crushing, and avoid manual operation; 3, reduction of the material after the sample is representative; 4, sealing design, no dust pollution, easy to clean, environmentally friendly requirements; 5, only placed at ground level, without a fixed infrastructure can work normally.
Our Saw-tooth Wave Jig is a new type of energy saving and high efficient gravity separation equipment and developed based on the traditional Sine Wave Jig. The difference between Saw-tooth Wave Jig and Sine Wave Jig is that the pulsation curve for jigging is saw-tooth wave shape, with speedy upward flow and slow downward flow. Descriptions Our Saw-tooth Wave Jig is a new type of energy saving and high efficient gravity separation equipment and developed based on the traditional Sine Wave Jig. The difference between Saw-tooth Wave Jig and Sine Wave Jig is that the pulsation curve for jigging is saw-tooth wave shape, with speedy upward flow and slow downward flow. Bed layer is elevated integrally and slowly dropped with a long effective loose time, allowing significant increase of handling capacity for unit screen surface, decrease of lower limit of grain size recovery and large save of make-up water for under size fraction. In practice, contrast of Saw-tooth Wave Jig and Sine Wave Jig shows up raises of recovery of Saw-tooth Wave Jig: Sn:3.01%, W:5.5%, Pb:1.63%, Zn:2.04%. Advantages and Characteristics 1 High capacity 2 High concentration ratio and high recovery 3 Easy to install, operate and maintain 4 The pulsation curve is saw-tooth wave shape facilitate heavy mineral to settling 5 Saving water 30-40% than ordinary jig 6 The pulsation speed very easy adjusted by regulator 7 Can achieve a good result in processing such as placer gold, tungsten,iron, tin, hematite, copper, tantalum-niobium, titanium, manganese, barite, zirconium, chrome and gemstone etc
Trommel screens provide a simple, efficient and economical solution to upgrade a wide rang of material and optimize the subsequent process steps of recovery. This method of screening helps to reduce operating and investment cost and to increase product quality, while allowing rapid and large volume processing. Descriptions Material feeds into the drum, is lifted up by the rotation as it falls back down. This action is repeated with each revolution along the length of the drum. The finer material passes through the screen openings while the larger material tumbles towards its eventual exit at the rear of the drum. The trommel screens provide a simple, efficient and economical solution to upgrade a wide rang of material and optimize the subsequent process steps of recovery. This method of screening helps to reduce operating and investment cost and to increase product quality, while allowing rapid and large volume processing. This material is then passed on to the downstream process equipment which can be in various forms such as centrifugal concentrator, spirals, jigs etc. Advantages and characteristics 1 economical and efficient solution for screening; 2 heavy duty trommel drum with lifters at the front to facilitate material break up; 3 screen replaceable for different mesh sizes; 4 multilayer screens; 5 easily change screen plates; 6 high efficiency and big capacity; 7 unique screen design, result in higher capacities, longer screen life and no material clogging; 8 heavy duty feed hopper; 9 discharge chute; 10 gear drive mechanism. Main technical parameters
Descriptions The rotary scrubber is an autogenous rotating drum scrubber, utilizing pebbles and rocks within the feed source to fracture and disintegrate clays, agglomerates and soft oxides. The scrubber spins slowly, similar to a giant washing machine. It churns the fines and oversize and water together, vigorously breaking up the soil matrix as well as liberating the target mineral from tough clay, schistâ??s and rock. Disintegrated material is homogeneously slurried within the drum, whilst the autogenous load is retained within the drum by reverse flights located at the drum discharge end. Slurry and washed oversize overflows the drum discharge throat to the concentric exit trommels. This material is then passed on to the downstream process equipment which can be in various forms such as centrifugal concentrator, spiral chute, jig etc. Advantages and Characteristics 1. Designed to break up alluvial gravels, clays and sand; 2. High capacity and high scrubbing power; 3. The long drum of the scrubber retains material for longer, more vigorous washing for complete separation; 4. Thickening type steel plate for the drum; 5. Heavy duty bearing, gear and roller; 6. Wearable screen at the exit of drum for screening; 7. One high output electrical motor driving a gear system providing efficient torque; 8. Adjustable rotary speed; 9. The water with high pressure flushed the inwall of drum; 10. Can accept material up to 230mm.
Description Log washer is mainly used to wash the manganese ore, iron ore, phosphate and other minerals, it is usually used to clean and separate the silt and stains from manganese ore, iron ore and other low-grade mineral. Also it suitable for scrubbing material which contains tough insoluble clays, conglomerates or soft stone. This machine drive the spiral stirring shaft depends on speed reducer and rotate in different directions, and the minerals which enter the tank were washed by water and stir strongly by blade. The sewage was overflowed at the end of tank, the cleaned minerals were lifted up along the blade and discharged at the beginning of tank. Advantages and Characteristics 1 Durable washing and conveying paddles 2 Fabricated with heavy duty shafts 3 Oversize bearings and gears
Description It is one kind of feeder as collection ore belt type conveyor for the ball mill, because the structure is simple, easy to operation, less power consumption, the feeding quantity can be evenly controlled, so it obtains widespread application. Main Technical Parameters Model Entrance size (mm) Exit size(mm) Swinging (mm) Swinging frequency (mm) Max Particle size (mm) Productive capacity (t/h) Motor (kw) Weight (kg) 300 300 300 300 300 125 0~90 68 100 8 1.1 213 400 400 400 400 400 50~150 0~170 47 35 12 1.1 272 600 600 600 600 600 150~150 0~206 45.5 50 25 1.5 558
Description The trough feeder used for feed massive material to receiving machinery from hopper, it is widely used to feed large size material (undressed ore and so on) into primary crusher of metallurgy, mine, chemical industry, building, dressing, coal ,and so on. Main Technical Parameters Model Entrance size (mm) Exit size (mm) Swinging (mm) Swinging frequency (mm) Max Particle size(mm) Productive capacity (t/h) Motor (kw) Weight (kg) 400*400 400*400 400*400 12 18.2 100 25-30 1.1 535 600*500 600*500 600*500 10-50 38.9 200 10-50 4 1054 980*1240 980*1240 900*800 20-50 23.7 350 36-90 7.5 1676
Description Rock hammer crusher can crush ore which is below 50mm or the tailings, middlings which in the uncompleted ore. And break up the useful metal from the ore, depending on the requirement of factory, it can crush the mineral particles in 1 to 180 mesh, and separate them in the shaking table. They are suitable for the small factory, and same times can take place of ball mill in some degree, Easy installation, easy operation, less investment, fast effect. The rock hammer crusher consist of rotor which with hammer, and the rotor consist of spindle, disk, pin and hammer. The motor drives the rotor to rotate at a high speed through the belt, the material enter the machine through the feeding port the rotating hammers with high rotation speed are crushing them, the small size mineral was discharge through the sieve and the large size still was crush and beat in the sieve until the crushed products meeting the required size can be discharged by the outlet and become the final products. Main Technical Parameters Model Capacity (T/h) Feeding Size (mm) Discharge Size (mm) Power at user option Motor (Kw) Diesel 200 500 1-2 50 1.8 15-18 24 300 500 3-6 50 1.8 18-22 30 400 600 5-10 50 1.8 25-30 45
Saw-tooth Wave Laboratory Jig is a new type of energy saving and high efficient gravity separation equipment and developed based on the traditional Sine Wave Jig. The difference between Saw-tooth Wave Jig and Sine Wave Jig is that the pulsation curve for jigging is saw-tooth wave shape, with speedy upward flow and slow downward flow. Advantages and Characteristics 1 High capacity 2 High concentration ratio and high recovery 3 Easy to install, operate and maintain 4 The pulsation curve is saw-tooth wave shape facilitate heavy mineral to settling 5 Saving water 30-40% than ordinary jig 6 The pulsation speed very easy adjusted by regulator 7 Can achieve a good result in processing such as placer gold, tungsten,iron, tin, hematite, copper, tantalum-niobium, titanium, manganese, barite, zirconium, chrome and gemstone etc Main Technical Parameters Model Hutch Diaphragm Feeding Size (mm) Makeup water (m3/t) Makeup water pressure (Mpa) Capacity (t/h) Power (kw) Dimensions (mm) Weight (Kg) Shape Area (m2) Stroke (mm) Frequency of stroke (r/min) JT0.57-1 Trapezoid 0.57 8.5 12 10 17 12-21 80-180
DescriptionsDouble deck shaking table is widely used for tungsten, tin, tantalum and niobium, gold, iron, manganese and other metals, ferrous metals, nonferrous metals, precious metals and other minerals and coal sorting. Traditional shaker covers an area of large, relatively low processing capacity,cost increases, double-shaker covers an area of inconvenience to deal with a large amount of equipment, low cost, Shaker is available in the double-sweep the election, featuring various operations, sorting coarse sand (2-0.5 mm), fine sand (0.5-0.74), sludge (0.074) different grain level, The same bed with hyperbolic rocker mechanism, the spring box in the shaker box, the crankshaft, rod, springs, rocker and so increase the size, material unchanged. The lower bed sharing a set of lower bed slope adjustment device used in shake liner support. Technical Specifications Model Unit DL4500/1850 DL3000/1320 Bed Size mm 4500/1850/1560 3000/1320/1100 Stroke mm 6-8 6-8 Frequency of stroke /min 240-380 210-320 Slope o 0-10 0-10 Feed size mm 0.02-2 0.02-2 Feed density % 10-30 10-30 Water t/h 0.8-1.4 0.6-1.2 Power kw 1.5 1.5 Capacity t/h 2.5-3.5 (coarse sand) 2.5-3 (coarse sand) t/h 1.6-2.5 (find sand) 0.8-2.5 (find sand) Overall dimensions mm 5600/1850/1560 4100/1320/1560 Weight kg 1650 1550
XFG series hanging cell flotation machine is used in the geological, metallurgical, building materials, chemical industry, mining and scientific research institutions, laboratory for stirring scrubbing, separating and cleaning minor samples. It uses the technology of frequency conversion stepless speed regulation, impeller, digital display, accurate adjustment.
1. Product performance standards: api 8a and sy / t5235. 2. Environmental conditions used sucker rod elevator A) allows the use at a temperature of -18, ~ 70, . B) meet the harsh conditions of oil field operations. 3. Sucker rod elevator's types: reed. 4. Material requirements: kava body is made of high-quality high-strength steel, handles made of high quality alloy forged steel. 5. Sucker rod elevator main technical parameters: A) applicable rod outer diameter: 5 / 8in ~ 1 1 / 8in. B) maximum load: 15t (135kn), 25t (225kn). 6. Sucker rod elevator major quality control requirements: 1) the chemical composition of each batch of material compliance with the relevant standards. 2) body 10% radiographic flaw detection, high stress area to meet the requirements of grade â?¡ gb / t5677, the remaining parts of the meet gb , level requirements / t5677's. 3) mechanical properties body of not less than: rm, 640 pma, rp0.2, 540 pma, z, 15%, a, 25%, akv, 42j (-20, ). 4) product 10% for 1.5 times the testimony load test. 5) all parts for magnetic particle testing, high stress area to meet the requirements of grade â?¡ gb / t9444, the remaining parts of the meet gb , level requirements / t9444's. 6) the main products from raw materials to the carrier using the site dating back the whole process. 7. Sucker rod elevator structure diagram and parts list below: Cdq (s) sucker rod elevator structure diagram.
Api 9a drilling wire line rope Construction: 1x3;1x7;1x12;1x19;6x7+fc/iwrc ;6x12+7fc;6x19+fc/iwrc;6x24+7fc;6x37 6x25fi+fc/iwrc;6x26ws;6x36+fc/iwrc, ws;8x19s+fc/iwrc;19x7 Quality assurance system: A. Strict selection of domestic high-quality hard-line to control theh product quality : using domestic the best materials, such as bomco wire rope company and shagang group. B. Perfect rod testing equipment: spectrometer, tensile testing machine, metallographic analyzer, high and low times metallographic analyzer.Testing for detection rod into the plant chemical costs, tissue properties and mechanical properties. C. With perfect wire rope and wire rope testing equipment: medium and small tensile testing machine, torsion testing machine, bending test machine, steel strands-tension fatigue testing machine, wire bending fatigue testing machine, fatigue testing Machine wire rope, wire rope pre-tensioning equipment, etc, we can test the the performance of wire rope. D. Wire rope production process using the advanced north america, germany management models. Meanwhile, the introduction of technology also brings the foreign advanced production organization and management mode such as quality track record, pre-production equipment, tooling, mold and other inspection records, processing management. E. Product organizational processes in according to gb/t19001 and apispecq1 for quality control. F. Corresponding to each batch of steel wire rope in accordance with rigorous testing standards, including process and final inspection. G. Approved by the american petroleum institute api monogram. And had passed the iso9000 certification.
Product Description BOP parts that we supply all come from original manufacturers, they are 100% interchangeable. BOP PART NAME: top sealing, front sealing, pipe ram, blind ram, slip ram, shear ram, spherical packer, bonnet, piston, shell. APPLY TO BELOW BOP: Brand: SHENKAI BOP. RONGSHENG BOP ETC OTHER FAMOUS BRAND BOP Type: Annular BOP, Single Ram BOP, Double Ram BOP, Shear Ram BOP Technical parameter Specification: 1. Standad: API 16 A and ISO 9001 2. Rated Pressure: 2000Psi to 15000Psi(14-17 Mpa) 3. Size: Nominal Bore: 7-1/16" to 21-1/4" (179.4mm to 539.75mm) 4. Type: Shear Ram/ Pipe Ram/ Variable Bore Ram 5. Usage : Single Ram BOP/ Double Ram BOP/ Three Ram BOP 6.Brand:Shenkai and Rongsheng. 7.Imitate: Camaron and Shaffer 8.U type and SH type Characters of BOP pare parts: In the structure, it is divided into annular blowout preventer with spherical plastic core, annular blowout preventer with cone-shaped plastic core, and blowout preventer with tube-shaped plastic core. Annular BOP top cap and housing are connected by bolts or claw blocks. Blowout preventer with spherical plastic core and dust-proof ring. Performance characteristics: reasonable structure, easy operation, long life of plastic core, adapt to a wide range, capable to seal pipe string with nominal paths from 0-DN in ans shapes, better performance by combining with ran blowout preventer in the use. Working of BOP pare parts: When wells must be sealed in case of kicks high pressure (10.5Mpa) oil from control systems enters into close-cavity under piston from housing oil outlet, to promote plastic core moving upward along ball surface, so that bearing tendons move closer to each other to moce the rubber between them to the center of wellhead so as to seal drilling tools or fully seal wellhead. In opening , hydraulic pressure oul enters into open-cavity above piston from housing oul inlet, to push piston moving downwards , so that plastic will reset with its own elasticity, wellhead will be open.
Downhole well drilling tool Roller reamer The Roller Reamer is designed for various reaming operation but particularly for various reaming operation but particularly for stabilization purpose when drilling in very abrasive formations. It will fit hole sizes ranging from â??6 to 28â?�. In addition, each body by simple adjustment of blocks and proper selection of cutters, will suit a wide range of hole sizes. Three different types(T, F, and B) of cutters are offered: Type T: Milled, machined with hardfaced sharp teeth for soft formations. Type F: Milled, machined with hardfaced flat teeth, for medium hard formations. Type B: Equipped with pressed-in tungsten carbide buttons, for hard formations.
