The most Economic and Practical Ultra-fine Powder Processing Equipment, the Energy-saving and Reduce Consumption Equipment fro ultra fine Powder Processing HCH ultra-fine grinding mill is especially suitable for ultra fine grinding. With yearsâ?? accumulation of experience in R&D, the HCH Ultra-fine Grinding Mill is a new ultra fine pulverizing equipment designed by Hongcheng. This mill is widely used to grind any non-metal minerals with Moh's hardness below 7 and moisture below 6%, such as talc, calcite, calciumcarbonate, dolomite, bentonite, kaolin, graphite, carbon black, etc. HCH Ultra-fine Grinding Mill features in space-saving, completeness, wide usage, easy operation, smooth performance, high performance-cost ratio and high efficiency. HCH1395 Grinding Mill is the biggest ultra fine circle-roll grinding mill in China. Working Principle Technological process: The pre-grinding raw ore material will be crushed into particlesï¼?10mm and transport to the feeding hopper by the elevator, then feed into the grinding chamber by the feeder. The grinding rollers equip on the rotary table rotates around the centre shaft. There is flexible gap between the roller and ring. The rollers rotate outward by the centrifugal function to compress the fixed ring. The rollers also self- rotates around the roller pin. When material passed through the gap between the ring and roller, the material will be smashed by the rotating rollers. Four layers of rollers. Material will be grinded 1st time when passing the 1st layer of roller and ring. Then be grinded second, third and fourth time when loop through each layer rollers. Thus the materials were grinded sufficient and obtain much fine powder. The powder fallen down onto the bottom table by gravity will goes up to the classifier for separation by the airflow from blower. The qualified fineness passing from the classifier will be collected by the pulse bag collector as final product, while unqualified fallen down for regrinding till passing through. The powder goes with air flow into the pulse bag filter and collects by the discharging valve. The wind path is in circulation and the airflow is in negative pressure. There will be no dust escape, so the equipment can ensure a no dust operation in workshop. Application Range HCH Ultra-fine Grinding Mill is widely used to grind any non-metallic minerals with Mohs hardness below 7 and moisture below 6%, such as talc, calcite, calcium carbonate, dolomite, bentonite, kaolin, graphite, carbon black etc.. This kind of mill is especially suitable for ultra fine grinding. The fineness can be adjusted from 0.045mm(325 mesh) to 0.005mm(2500 mesh), whose range is much wider than that of traditional Raymond Mill.
New Generation of Large Powder Grinding Mill, large powder-making equipment with higher production capacity and efficiency Following the powder-making development trends, HC1700 grinding mill, with revolutionary and innovative technology, is designed by our engineers who devote great effect to improving the structure and capacity of traditional Raymond Mill. HC1700 grinding mill is a better choice for large scale powder-making projects. It effectively increases the production capacity while reducing the power consumption. Compared to the traditional mill (5R Raymond mill), the capacity of HC1700 grinding mill is about 2.5 to 4 times higher. HC1700 grinding mill is a kind of large powder-making equipment with higher production capacity and efficiency. The working principle of HC1700 Grinding Mill Powder processing system technological process: raw material will be transport to semi-open shed by special vehicle, and then be shoveled into the crusher to be crushed into particles smaller than 40mm. The material particles will be raised to the storage hopper by the elevator and then be evenly sent to the main mill for grinding by feeder. The qualified fine powder will be classified and blew to the pulse dust collector as product and finally discharged from the dust collector. The product will be transported to powder storage. The system is designed as open circuit system with full pulse dust collecting (able to collect 99.9% of the powder), so the equipment has higher capacity and lower pollution. The product can be deep-processed according to actual technology. HC grinding mill has really high capacity so the product cannot be packed by hand-filling, the packing job is supposed to be done after the powder be sent to the storage tank. Application Range The HC1700 grinding mill is widely used to grind almost any non-metallic minerals with Moh's scale of hardness below 7 and moisture below 10%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, ceramic, bauxite, marble, feldspar, barite, fluorite, gypsum, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbide,bentonite, manganese etc. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh), whose range is much wider than that of traditional raymond mill.
Raymond Mill - the originator of Pendulum Grinding Mill In terms of traditional pendulum roller mill, the R-series grinding mill has been upgraded in many aspects. All of the technical parameters takes the leading role in China mill industry. The R-series grinding mill ranges from 2R to 6R, including 2R2713, 3R3220, 4R3216, 4R3218, 4R3220, 5R4121, 5R4125, 6R5127. This mill is widely used to grind any non-metal minerals with Moh's hardness below 7 and moisture below 6%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, bauxite, marble, feldspar, fluorite, gypsum, barite, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbide, bentonite, manganese. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh). Working Principle Raw material is firstly broken by jaw crusher into required particle size, which are carried by bucket elevator up to the storage hopper. The vibration feeder then conveys the crushed materials at a fixed rate into the grinding chamber of the main unit for pulverizing. The three rollers hung upon the spider-arm are running around the shaft. With the centrifugal force, the four rotational rollers will go around the ring tightly. The raw materials is put up between the rollers and rings by the blade to make the raw materials into powder. The grinded materials is blown up to the classifier, through which the powder is separated by the airflow. Coarse particles fall back down to the mill for regrinding. The needed particles will go into the collector where products will be removed through the discharge opening. The purified air flows to the air blower through the pipe above big cyclone collector. Air flue is circular type. Air stream in all pipelines is negative pressure except for that in the air blower and grinding chamber, which improved the working condition in the workshop. Wind volume in air flue increases as the moisture in material changes into vapour leaking in from the flange conjunctions and feed opening. Added air volume is transporting through the air blower and after-wind pipe, to simple collector. The end powder enters the collector with air stream and discharged from discharge valve. Application Range R-series Grinding Mill is widely used to grind any non-metallic minerals with Mohs hardness below 7 and moisture below 6%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, bauxite, marble, feldspar, barite, fluorite, gypsum, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbidebentonite, manganese. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh), whose range is much wider than that of traditional raymond mil l.
HC3000-Super-Large Pendulum Mill in Asia, Technical Revolution of Pendulum Mill Industry, Upgraded Production of Traditional Raymond Mill HC3000 Super Large Grinding Mill is the largest pendulum roller mill in china, developed by our engineer on the basis of HC1700 grinding mill. With 5 patents, the HC3000 grinding mill is widely used to grind almost any non-metallic minerals with Mohâ??s scare of hardness below 7 and moisture below 10%, such as kaolin, calcite, marble, talc, manganese, ceramic, etc. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh). Not only can the HC3000 grinding mill live up to the national industrial policy and meet the needs of mass production, but also fills the gap of large-scale mill in the mill industry. This kind of mill plays a leading role in grinding technology, production capacity and power consumption per ton. With a production capacity of 90T/H, the HC3000 grinding mill can replace all kinds of mill, especially suitable for large-scale powder-making industry such as desulfurization and manganese. Working Principle Powder processing system technological process: raw material will be transport to semi-open shed by special vehicle, and then be shoveled into the crusher to be crushed into particles smaller than 40mm. The material particles will be raised to the storage hopper by the elevator and then be evenly sent to the main mill for grinding by feeder. The qualified fine powder will be classified and blew to the pulse dust collector as product and finally discharged from the dust collector. The product will be transported to powder storage. The system is designed as open circuit system with full pulse dust collecting (able to collect 99.9% of the powder), so the equipment has higher capacity and lower pollution. The product can be deep-processed according to actual technology. HC grinding mill has really high capacity so the product cannot be packed by hand-filling, the packing job is supposed to be done after the powder be sent to the storage tank. Application Range HC3000 Grinding Mill is widely used to grind any non-metallic minerals with Moh's hardness below 7 and moisture below 10%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, bauxite, marble, feldspar, barite, fluorite, gypsum, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbide, bentonite, manganese. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh), whose range is much wider than that of traditional raymond mill.
Introduce of Stone mill/micro mill/ micro grinder mill/ micro grinding mill: five models: HGM80, HGM90, HGM100, HGM100A, and HGM125 finished production fineness: 300meshes~3000meshes, 5-47 micron the capacity (ton/hour) ranges from 0.4T/H to 12T/H application: HGM series stone mill/micro mill/ micro grinder mill/ micro grinding mill can process various kinds of stones and rocks, such as: Kaolin, limestone, calcite, marbles, barites, gypsums, pyrophyllites, dolomites, calcium carbonates, pigments, clays, coals, carbon black, activated carbons, feldspar, talc, mica, carbon black, petroleum coke, alumina, chromic oxide, quartz, cements, up to more than 100 materials. Working Principle of Stone mill/micro mill/ micro grinder mill/ micro grinding mill: The crusher will crush the big materials into small ones, and then the elevator will send them to the hopper. The vibrating feeder will send the materials to the middle of first dial evenly. The motor of main equipment drives the main shaft and dial through reducer, and the dial drives numbers of rollers moving in the ring channels via pins. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and bring the crushed materials to classifier. The rotating turbo in the powder collector will make the coarse materials return to the mill and regrounded, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Intorduction of Ultra Fine Vertical Roller Mill Brand: Clirik Model: CLUM Application: Micro powder vertical roller mill are suitable for huge capacity producing, widely used in grinding non-flammable and non-explosive materials under 7(the Moh's hardness), such as quartz, feldspar, calcite, talcum, barite, fluorite, iron ore, copper ore quartz, especially for slag, cement clinker, zircon sand, fly ash and carborundum, coal, etc. Input Size: Below 25 mm. Output Size: Could be adjusted between 300-3000 mesh. Capacity: According to your fineness choose, the capacity is about 0.2-45 t/h. Ultra Fine Vertical Roller Mill Working Principle The grinding disc is driving by motor through reducer. The material falls to grinding disc from the feed opening. The materials are driven to the edge of disc by the centrifugal force and crushed into fine powders by rollers. Then, the hot air from the nozzle take the fine powder to high effiency classsifer.The qualified powder are taken by the air to the powder collector to be collected, while the unqualified powder are sent back for regrinding.
The purpose of the micro powder grinding mill is for super-fine grinding materials with hardness less than 6 in Mohs scale and humidity less than 6 percent such as kaolin, limestone, calcite, marble,talcum, barite, gypsum, dolomite, bentonite mud,mica, pyrophyllite, sepiolite, diatomite, graphite, alunite, fluorite, potassium feldspar, phosphorite, pigment and so on. The granularity of the end products is 325-2500 meshes (0.044-0.0055mm). Working Principle Of Micro powder grinding mill: The main bearing and each dial are driven by electromotor of main equipment through reducer, and numbers of rings and rolls which are rolling in the ring channels are driven by dial through plunger. After being crushed by hammer crusher, the big materials become small ones and they are sent to the storage bin by elevator. The electromagnetic vibrating feeder sends them to the middle of first dial evenly; the materials will be driven to the edge of dial by centrifugal force, and fall into the ring channels and are pressed, crushed and ground by the grinding rings and rolls. Then the materials fall into the second and third ring and crushed and ground. The high pressure centrifugal blower inhales air from the outside and blow the materials which are ground in the third ring to powder Separator. The rotating turbo in the powder Separator makes the coarse materials return to the mill and reground, while the fineness mixes with the air and be drawn to the cyclone and be discharged from the discharging valve which is in the bottom of it. The air which mixed with very little fineness are purified by impulse dust catcher and discharged by blower and muffler. Features Of The Micro powder grinding mill: 1. High-efficiency and low consumption With the same end-products fineness and motor power, its output is over 1 time of that of Jet Mill, Mix Mill, and Ball Mill. 2. Easy-damaged parts with longer working life The grinding roll and ring are made of special materials. Generally, their work life is more than one year, but, which could come up to over 3 years, when it processes calcium carbonate and Calcite. 3. Security and Reliablity Because there are no rolling bearing and bolts in the grinding chamber, we can not see the problems of bearings and sealings easily damaged and machine destroyed due to the bolts looseness. 4. Cleansing and Environment Protection Adoption of Pulse dust collector and muffler reduces the industrial dust pollution and noise, which reaches the National Standard.
So far, the technology of the ultra fine grinding mill has been continuously improved, and the fineness of the powder is now becoming more and more strict. For the fine powder market, the ultra fine grinding machine is a professional grinding equipment. What ultra fine grinding mill machines are currently popular on the market? Shanghai Clirik focuses on R&D and manufacturing of grinding machines. The 1000 mesh ultra fine grinding mill machine is a device that focuses on fine powder processing. How much is this 1000 mesh ultra fine grinding mill machine? What are the characteristics of the fine powder ultra fine grinding mill? The equipment is a fine powder processing equipment, which has a ring roll impact, rolling, grinding, and is processed into a powder through three layers of loops. The ground powder can be adjusted between 200-3000 mesh, and the powder has good quality. Fine fineness and fine grading, it is a professional fine powder processing equipment. HGM ultra fine grinding mill is an economical and practical ultra-fine powder processing equipment. It can deep-process various non-metallic minerals with Mohs hardness below 7 and humidity below 6%. The product fineness can be from 200 mesh to 3000 mesh. Adjust between. There are many advantages, such as small footprint, wide application, simple operation, convenient maintenance, stable performance, etc., which has won the favor and love of non-mineral fine powder processing customers. How is such a ultra fine grinding mill sold? How much is the price? In fact, as a manufacturer, Clirik has been committed to providing tailor-made services. For customers' grinding needs, Clirik can customize a professional selection configuration, and the price of the ultra fine grinding mill is more. Reasonable, therefore, if you want to know the price of grinding equipment, welcome to provide information on materials, processing fineness, production capacity, equipment installation area, etc., customize the professional selection plan and equipment prices, and help non-mine projects to create greater value.
Vertical Cement Grinding Mill manufactured by China ZK Corp, for example double-swing type, underground type and step-started type jaw crusher, cone crusher, rotary crusher, single - section hammer crusher, tube coil grinding mill, grid type ball mill, bucket elevators, plate type, dissepiment and vibration feeder, screw sand mixer and heavy duty soil spreader for open-pit coal mining, are widely used for the industries of metallurgy, building construction, road construction, and chemical industry as well as silicate industry. China zhengkuang has provided various kinds of large and medium size complete sets of cement production equipments for more than 300 cement customers in domestic market. And engineering for equipment and technology, manufacturing, installation and commissioning as well as the supply of the spare parts and the training service can be offered by China ZK for customers. The gantry crane, the overhead traveling crane, tower crane, hoists, and other various kinds of crane equipment which have been designed and manufactured by China zhengkuang are widely used in the fields of handling of sluice gate for the hydro-power station, loading and unloading vehicle, outdoor handling and handling of the heavy duty components. China ZK has supplied large amount of super-high quality products for national water conservancy projects, the main Our products advantages: 1. High grinding efficiency and low power consumption. 2. Low metal consumption in unit product. 3.Bed grinding with low noise. 4. Negative pressure and low dust pollution. 5.Small floor space, compact layout, system equipment with light weight and low investment for civil construction. Structure of Vertical Cement Grinding Mill: 1. Separating efficiency increased by combined separator. 2. No need to prepare material on the disc before start up, the function including auto lift and fall roller, and on-load staring can be achieved. 3. The sealing adopt welding arc panel, structure is simple and reliable with good sealing effect. 4. The grinding roller can be turn out from the mill easily by the roller turning device, and convenient for maintenance.
