Measuring and testing equipment, laboratory instrument, textile testing machine, tester.
Inspection equipment, testing equipment, laboratory instrument, flame tester, physical measurement tester.
Temperature humidity chambers, thermal shock test chamber, precision hot air oven, aging test chamber, temp humidity and vibration test chamber.
Laboratory testing device, environmental chamber, laboratory incubator and oven, temperature and humidity simulation test equipment.
Lab furniture, lab furniture, steel and wood lab furniture, lab furniture, pp lab furniture, eyewash, laboratory sink.
Universal material testing machine, environmental test chamber, physical test equipment.
Walk-in Room Available Constant Temperature and Humidity Test chamber Applicable range Walk-in Room Available Constant Temperature and Humidity Test chamber are applicable for testing the performance indexes of aeronautic & astronautic products,ships,weapon, accdemies, motorcycle, information electronics,instruments & meters, materials, electronic engineering, electronic products, various electronic elements, foodstuffs, chemistry, building materials, luggage, adhesion tape, printing, packaging, materials, plastics, medical and so on in high-low temperature and humidity alternation environment. Features(Walk-in Room Available Constant Temperature and Humidity Test chamber)
Steel structure; cabinet with 1.2mm cold-rolled steel plate bending, stamping, surface after degreasing, pickling, phosphorus into anti rust treatment, thenelectrostatic powder spraying epoxy protective layer of acid and alkali corrosion resistant surface treatment, surface using 12.7mm solid physiochemical board panel, the circumference edge grinding processing, corrosion resistant, acid and alkali resistance, resistance, wear-resistant, anti static, antibacterial, flame retardant, particularly suitable for chemical, physical, biochemical, clinical room table. Holding a special mould laboratorymolded pvc handle, accord with human body engineeringstandards; hinge adopts 304# stainless steel; guide rail adopts 16 inch wide plate three section type ball mute slide, surface galvanized processing; professional moldcomposite structure; adjustable screw is m12*50mm, the outer cover for an injection molding die, Wood packing
ZY6014A (Vertical-specimen) Flame Tester 1.Introduction: This apparatus is certificated by Guangzhou Hua Mei UL company ,it applies to research and manufacture for illumination, household, machine tool, motor, and such electric and electronic equipments and parts. It is also used to insulation materials, project plastics and other materials. 2. Standards: UL1581(section 1080.1£1080.14) , UL13. UL14 UL1655(VW-1 burning test). CSA (FT-1¡¢FT-2) 3. Main components: burning chamber ¡¢observation Windows¡¢ operation windows¡¢control system ¡¢gas control and so on . 4. Main parameters : 4.1 Burning chamber outside size: 2.4m(L)*1m(W)*2.5m(H) 4.2 Observation Windows: 3 observation Windows, made by reinforced glass, size: 730mm(H)*420mm(W) 4.3 Operation windows: 4 operation windows, interior diameter 150mm, outside diameter 220mm.sealed by 600mm long-arm leather glove. 4.4 Air inlet : 4 air inlets ,which diameter is 160mm, 4.5 Bottom anchor : bottom anchor size 2.4(L)*1m(W)*0.7m(H), 6 pulleys of which 4 are with lock. 4.6 Light equipment : 1 anti-fog,anti-smoke,ring lamp. 4.7 Control system: 1 sheet of burning instrument, 0 to 99.99s setting arbitrarily. 1 sheet of stop burning instrument, 0 to 99.99s setting arbitrarily . 0 to 999999 times setting arbitrarily. negotiable
ZY6056 Needle Flame Tester 1. Introduction : This device applies to electrical and electronic equipment and components ,also suitable for electrical insulating materials or other solid materials ,using simulation technology assess dangerous of catching fire or flame driven from internal equipment under fault condition. 2. Standards: IEC60695-2-2. GB/T5169.5-1997. 3. Main components: needle combustor, temperature measurement system , test chamber and so on. 4. Main parameters 4.1 Burner :inner diameter 0.5mm, length 35mm. 4.2 Flame standard : length more than 12mm. 4.3 Heat speed :100 - 700C costs 2.5S 4.4 Chamber capacity 0.5M 60cm(L) * 95cm(W) * 90cm(H) 4.5 Conductive copper ¥Õ4.0 * 6.0mm, 4.6 Outsize :61cm(D) * 120cm(W) * 105cm(H).
ZY6078 Vulcanization Tester 1. Introduction : This device applies to show vulcanization curve , so that a new hand can easily get the best reasonable ingredients and balanceable formula of scorching and vulcanization by computer and software . 2. Main components : 2.1 Machine parts: cabinet , upper and bottom mould cavity ,and so on. 2.2 Electrical control system 2.3 Printer 2.4 Pneumatic system.
ZY 6192 Halogen Release Measurement Device 1. Introduction: this device applies to measure halogen content PH conductivity when wires and cables are burning according to IEC60754. 2. Standards:GB/T17650.1-1998, GB/T17650.2-1998, IEC60754-1:1994, IEC60754-2:1991 . GB/T19666-2005, GA306.1-2007, GA306.2-2007, UL2556-2007. 3. Main components : quarts material tubular furnace combustion tube, air collection system, air supply system , PH meter , conductivity analyzer 4. Main parameters: 4.1 Tubular furnace chamber size : 42mm * 600mm, power input :220V/10kw. 4.2 Combustion tube 40mm, 4.3 PH meter : precision 0.02PH. 4.4 Conductivity : measurement scope :(0~1¡Á105)¦ÌS/ cm. 4.5 Air flex meter :20-200L adjustable.
Climate Chambers including different kinds of Temperature( Humidity) Test Chamber, Low-pressure(Altitude Simulation) Test Chamber, Salty Mist Spray Test Chamber, Rain Spray Test Chamber, Thermal Abuse Test Chamber, High-Temperature Aging Test Chamber, etc. Contact us freely!
Environmental Chambers including different kinds of Temperature( Humidity) Test Chamber, Low-pressure(Altitude Simulation) Test Chamber, Salty Mist Spray Test Chamber, Rain Spray Test Chamber, Thermal Abuse Test Chamber, High-Temperature Aging Test Chamber, etc. Contact us freely!
Different types of Environmental Chambers are manufactured by Bell Experiment Equipment Co., Ltd. For example Temperature Cycling Test Chamber, Temperature(Humidity) Test Chamber, Low-pressure(Altitude Simulation) Test Chamber, Thermal Abuse Test Chamber, Thermal Shock Test Chamber, Salty Mist Spray Test Chamber, Rain Simulation Test Chamber, Sand Dust Test Chamber, Walk-in Temperature Humidity Test Chamber, etc.
1. Application Ultraviolet aging test chamber uses ultraviolet lamp as light source. By simulating the ultraviolet radiation and condensation in natural sunlight, accelerated weatherability test of materials is carried out to obtain the results of weatherability of materials. It can simulate the environmental conditions such as ultraviolet, rain, high temperature, high humidity, condensation and darkness in natural climate. By reproducing these conditions, it can merge into a cycle and let it automatically execute the number of cycles. 2. Standards Conforms with ASTM G 153, ASTM G 154, ASTM D 4329, ASTM D 4799, ASTM D 4587, SAE J2020, ISO 4892, all current UV aging test standards. GB/T14522-93 National Standard of the People's Republic of China--Accelerated Test Method for Plastics, Coatings and Rubber Materials for Machinery Industry Products-Artificial Climate GB/T16585-1996 National Standard of the People's Republic of China-Test Method for Artificial Climate Aging of Vulcanized Rubber (Fluorescent Ultraviolet Lamp) GB/T16422.3-1997 standard design and manufacture of plastic laboratory light source exposure test method. 3. Product Parameters Standard Configuration Editor For Test Box (1) Install 8 UV ultraviolet lamps on both sides of the studio. (2) Sample holder number: 20 pieces. (3) Sample holder size: 404 x 105 (mm) (4) The heating mode is inner tank water heating, fast heating and uniform temperature distribution. (5) The drainage system uses the return vortex type and U type sedimentation device to drain the water. (6) The distance between the surface of the sample and the ultraviolet lamp is 50 mm and parallel. (7) The actual workroom is made up of test samples and brackets. (8) Internal water level automatic replenishment. (9) The box cover is bidirectional flip type, easy to open and close. (10) The bottom of the test box adopts high quality and fixed PU wheel. 4. Power Supply Condition Editor Power requirements: AC380V ± 10% 50 ± 0.5Hz three-phase five wire system. Preinstalled power: total power +2.0KW Users are required to install air or power switches for the equipment at the installation site.
I. Application Xenon lamp test chamber uses xenon arc lamp which can simulate all sunlight spectrum to reproduce destructive light wave in different environment. It can provide corresponding environment simulation and accelerated test for scientific research, product development and quality control. Xenon lamp test chamber can be used to select new materials, improve existing materials or evaluate the durability of materials after composition changes in the test, is a good simulation of different environmental conditions that materials exposed to sunlight changes. 2. Standards GB/T16585-1996, GB14522-93, GB/T16422.3-97, ASTM D2565 Comply with GB/T16585-1996, GB14522-93, GB/T16422.3-97 and ASTM D2565 standards. 3. Main technical parameters 3.1Humidity deviation: + 2.5% R.H (Humidity75%R.H), + 3% R.H (Humidity 75%R.H) (without light) 3.2 Types of Light Sources: imported air-cooled all-solar spectral long arc xenon lamp (average service life of 1600 hours or so) 3.3 Rainfall time: 1~9999 minutes, adjustable. 3.4 Rain cycle: 1~240 minutes, interval (break) adjustable 3.5 Light source wavelength range: 300-800nm 3.6 Humidifying power: about 2KW 3.7 Light source irradiance: 290~800nm: 100~600w/m2 300~890nm: 200~1200w/m2 340nm: 0.3~1.2w/m2 420nm: 20~120w/m2 3.8 Distance between arc center to sample frame: 350 ~ 380mm 3.9 Rotating speed of sample basket: 1r/min 3.10 Water spray cycle: Water spray time: 0 ~ 99h59min, continuous adjustable Stop time: 0 ~ 99h59min, continuous adjustable. 3.11 Lighting time: continuous programmed control. External dimension W x D x H: 1050 x 1050 x 1750 mm Internal dimension W x D x H: 500 x 500 x 600 mm Temperature range 080 Temperature deviation ±2 (without illumination) Humidity range 30 ~ 98% R.H Spectral wavelength 300nm ~ 800nm Xenon lamp power 1.8KW Life span 1600 hours Blackboard temperature 85±3 Power About 4KW; 220V±10%, 50HZ
Stainless Steel Thermal Shock Test Chamber 1. Principles and methods It uses the low temperature and high temperature storage hot trough, according to the movement need, uses the cylinder valve to switch the cold and hot air, thus achieves the fast temperature impact effect, balances the temperature control system (BTC) + the special design supply air circulation system, controls the SSR by the P.I.D. method, causes the heating amount of the system to be equal to the heat loss, therefore makes it long-term stable use. 2. Main Parameters 1. Performance: wind cooling type at room temperature ±25, no load. (1) Impact temperature range: - 40 ~ 150 (2) Temperature setting range of high temperature cell: + 60 ~ + 200 The temperature rise time of the high temperature tank is about 35 minutes from RT (room temperature) to + 200 degrees (room temperature + 10 ~ + 30). (3) The temperature setting range of cryogenic tank is from - 60 to - 10 . The cooling time of the cryogenic tank is from RT (room temperature) to -60 , which takes about 90 min (room temperature + 10 ~ + 30 ). (4) Laboratory temperature: - 40 - 100 (5) Temperature fluctuation: ±1 . (6) Temperature uniformity: ±2 . (7) Shock recovery time: - 40 ~ +100 takes about 3 minutes (no load), (high and low temperature shock isothermal time is more than 30 minutes each).
I. Application 1.1 Dust-proof test box is designed and manufactured according to GB4208-93 (equivalent to IEC60529-2001) "Shell Protection Grade (IP Code)" and is suitable for sand and dust test of electrical products with the first characteristic digits of 5 and 6 (IPX5 and IPX6). 1.2 The test chamber can provide non-laminar vertical circulating airflow of dust, which can be controlled regularly. It is equipped with a vacuum pump to pump air into the outer shell of the tested product, and it can adjust the pumping volume and pressure difference.In addition,the air temperature control device is installed in the chamber to ensure that the test is carried out under the standard environmental conditions. 1.3 According to the standard requirements, this test chamber adopts the artificial analogy dust environment to test the dust-proof ability of the tested products, and its specific requirements and eligibility criteria should be in accordance with GB4208-93 (IEC60529-2001) or product-related standards. 2. Structure and Material Material: both inside and outside gallbladder adopt SUS high grade stainless steel plate door: tempered glass door. Sample outlet: dust-proof socket Controller: programmable controller (the controller has the following arbitrary setting control functions). A. Dust blowing time (stop and blow) h/m/s adjustable B. Cycle: arbitrary adjustable C. Preset test time: 0s to 999h99m99s arbitrary adjustable D. Power on: break through break Metal screen size: nominal diameter 50 um, nominal distance between lines 75 um Blower: all plastic centrifugal fan Vacuum system: equipped with pressure gauge, air filter, pressure regulating triple parts, connecting pipe (vacuum pump with another, when ordering instructions) Remarks: The test box can meet the requirements of protection grade test for household appliances, low-voltage appliances, automobile and motorcycle parts in GB2423, GB4706, GB4208, DIN. The device can not meet the sand and dust test in GJB150.
1. Application Salt spray corrosion test box is designed for surface treatment of various materials, including metal plating, hardware, electronic components, chemical coatings, baking paint, automobiles, motorcycles, hardware sanitary ware, screws, springs, magnetic materials, organic and inorganic skin film, anodic treatment, rust-proof oil and other industries, testing the quality of its products and its corrosion resistance. 2. Standards Conforms to ASTM G85-02 and GB/T2423.17 test standards. 3. Performance parameters Laboratory volume: 108 L, studio size: 600 * 450 * 400 mm Laboratory temperature: 35 ~ 0 The temperature of the saturated air cylinder is 47 to 63. Maximum capacity of test fluid: 15 L External dimension: 1075 * 630 * 1185 mm Can be customized according to customer requirements.
