Concrete reinforcement mesh is classified ribbed concrete reinforcement mesh and plain steel wire concrete reinforcement mesh. The wire of ribbed concrete reinforcement mesh is 3 faces indentation.Please see figuer Concrete reinforcement mesh is always used on residential slabs and footing-construction and BCA complying with AS 2870,which is always paced in all reinforced conrete members to stop the concrete cracking. And F62/F72/F82/F92/F1018 concrete reinforcement mesh is old specification,was replaced by SL62/SL72/SL82/SL92/RL1018.For example:previously called F62(now SL62) is wire diameter 6mm bars welded together in a 200mm square grid.the panel size is 2.4m X6m. The Tensile strength is 300Mpa. The concrete reinforcement mesh specification as below: Reinforcing Mesh Code wire diameter aperture edge open width length weight per sheet(kgs) F62 5mm 200*200mm 200mm 2.4m 6m 20.92 F72 6mm 200*200mm 200mm 2.4m 6m 30.12 F82 7mm 200*200mm 200mm 2.4m 6m 41 F92 8mm 200*200mm 200mm 2.4m 6m 53.55
Hard drawn mesh is specified in AS/NZS 4671: 2001. Heyou wire mesh offers a range of mesh sheet sizes and certres to meet the needs of typical New Zealand applications. Our scope covers standard sheet sizes of 4.65m x1.97m and larger economical sheets 6.15m x2.42m. The pitches are 150mm x150mm or 300mm x 300mm. AS/NZS 4671: 2001 specification for hard drawn mild steel wire for concrete reinforcement The mechnical property required by standard AS/NZS 4671: 2001 Nominal diameter(mm) Minimum 0.2% proof stress(Mpa) Tensile strength(Mpa) Minimum Maximum Up to and including 3.15 485 575 855 Over 3.15 485 575 775 The pitch (a) of longitudinal bars and transvers bars is not less than 50mm. The pitch is measured as below shown. The tolerance of the pitch is not more than 0.075 times the specified value. Specification of hard drawn mesh Model Pitch / certres Wire dia.(mm) Length (mm) Width (mm) Newt cover (sqm) Heyou reinforcing item Cross section sqmm / m Mass per sqm kg / sqm No. of Longitudinal wire No. of Cross Wire Overhangs of Longitudianal wire Overhangs of Cross wire Weight (kg) 668 150 4.0 4650 1970 7.525 668L 83.8 1.315 14 31 75/75 10/10 12.44 665 150 5.3 4650 1970 7.525 665L 147.1 2.309 14 31 75/75 10/10 21.85 663 150 6.3 4650 1970 7.525 663L 207.8 3.263 14 31 75/75 10/10 30.87 665 150 5.3 6150 2420 12.760 665E 147.1 2.309 17 41 75/75 10/10 35.29 663 150 6.3 6150 2420 12.760 663E 207.8 3.263 17 41 75/75 10/10 49.86 662 150 7.1 6150 2420 12.760 662E 263.9 4.144 17 41 75/75 10/10 63.33 661 150 7.5 6150 2420 12.76 661E 294.5 4.624 17 41 75/75 10/10 70.67 300 Centres of hard drawn mesh 668 300 5.6 4950 2220 10.08 84/10 82.1 1.289 4*5.6mm+4*4.0mm 19 25/25 10/10 15.85 665 300 7.5 4950 2220 10.08 147/10 147.3 2.312 6*7.5mm+4*5.3mm 19 25/25 10/10 28.36 665 200 6.1 5050 2020 8.312 SE62 RES 146.1 2.294 11 26 25/25 10/10 24.79 665 200 6.1 5850 2420 11.93 SE62 146.1 2.294 13 30 25/25 10/10 34.10 665 300 7.5 6050 2420 11.58 SE73 147.3 2.312 9 21 25/25 10/10 36.51 665 300 7.5 5000 2270 10.08 SE73DE 147.3 2.312 8*7.5mm+2*5.5mm 19 7.5mm:25/255.5mm:25/25 10/10 30.69 664 200 7.0 5650 2220 10.432 SE72 192.4 3.02 12 29 25/25 10/10 39.93 662 200 8.0 5650 2220 10.432 SE82 251.3 3.946 12 29 25/25 10/10 52.16 661 200 9.0 6100 2420 12.76 SE92 318.0 4.99 12 29 25/25 10/10 71.65 Equivalents are based on the nominal sectional area of steel per meter width. Additional meshes specification are available as a special order.Minimum order quantities will apply. Please mail to us Heyou wire mesh for further details. What does SE62 mean? In standard AS/NZS 4671: 2001, the designates letters to be used to identify reinforcing mesh products:
Reinforcement steel mesh was welded by automatic electrical resistance welding machines conformance to standard AS-NZS 4761-2001. The material of reinforcement steel mesh is 250N, 500N, 500L, 300E, 500E. Reinforcement steel mesh is very poupular in civil engineering and construction. It always used on road subgrade, building foundation, tunnel support and reinforced,mine and coal reinforced and support, bridge construction etc. During construction works, It is not only increase our working speed and time but also save 75% construction cost and enhance the crack resistance. The specification of rectangular reinforcement steel mesh as below: Rectangular Reinforcing Mesh 2.4m*6m=14.4sqm Code Cross wire Longwire mm Mass/sheetkg Quantityin pack Pitch@mm No. x dia., mm Pitch@mm No. x dia., mm RL718 7.60 @ 200 30 x7.6 6.75 @ 100 25 x 7.6 68 20 RL818 7.60 @ 200 30 x7.6 7.60 @ 100 25 x7.6 79 20 RL918 7.60 @ 200 30 x7.6 8.55 @ 100 25 x 8.55 93 20 RL1018 7.60 @ 200 30 x7.6 9.50 @ 100 25 x9.5 109 15 RL1118 7.60 @ 200 30 x7.6 10.65 @ 100 25 x10.65 131 15 RL1218 7.60 @ 200 30 x7.6 11.90 @ 100 25 x11.9 157 10 The panel size 2.4m*6m is very pouplar in Australian market,but considered the transportation in container by sea and saved cost, we advise the customers to change the panel size to be 2.2m x5.8m.
Heyou factory can produce concrete reinforcing mesh which is the specification of New Zealand standard AS-NZS 4761-2001. Details of concrete reinforcing mesh: Material: 250N, 500N, 500L, 300E, 500E Mesh Pitch: 200mm Wire: ribbed steel wire & plain steel wire Overhang length of two sides: 100mm Wire diameter:6mm, 7mm, 8mm, 9mm Size: 2.4m * 6m or 2.2m * 5.8m Packing: 1ton more or less per bundle HS code: 73142000 Production Standard: AS-NZS 4671-2001 The specification of concrete reinforcing mesh as below concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m Structural and skatch SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84 Are you a Manufacturer? Heyou wire mesh factory as a professional factory for reinforcement mesh, which has 10 workshops, more than 200 workers, advanced production line,perfect production process, Strict production regulations. We own ourselves laboratory for inspected chemical composition and mechnical property of raw material, drawn wire diameter measuring,cutting wire length measurement, and full pieces of concrete reinforcing mesh which contained pitch of wire to wire, shearing resistance, tensile strength, yeild strength, elongation, bend test, weight tolerance, size tolerance, ribbed height, pitch of transverse wire ribbed, surface quality and etc. We're strictly to do everything in order to guarantee our concrete reinforcing mesh quality. Therefore, Heyou Wire Mesh has a high reputation in our field as real manufacturer.
Construction reinforcement mesh was made by plain steel wire. It main used on building construction complied with standard AS NZS 4671-2001. The material is 250N, 500N, 500L, 300E, 500E, the mesh size is 150x150mm, wire diameter is 5.3mm and 4.0mm and the overhang length is in both sides. These specificate is very pouplar in New Zealand civil engineering field. More features of construction reinforcement mesh and ours as below: 1. high quality raw material 2. electric resistance welding machine made it which has firmly solder join, size precision,and appearance good-looking 3. Professional management team 4. Complete QC rules and regulations 5. A full of laboratory testing instruments Advantage of construction reinforcement mesh by AS-NZS 4671-2001 standard: 1. Save 30% of steel bar dosages 2. Reduce 50%-70% work time, improve construction progress and shorten construction period. 3. Cut down 5%-10% construction cost 4. Used widely,it has a good market development prospects. The specification of construction reinforcement mesh by AS-NZS 4671-2001 standard as below: concrete reinforcing mesh specification Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6x2.4m sheets Cross-sectional area/m width No. x dia., mm Pitch, @mm No. x dia., mm Pitch, @mm Unit area, kg/sqm Sheet, kg Long' l bars, sqmm/m Cross bars, sqmm/m structural SE92 13 X9.0 200 30 X9.0 200 5.0 75 318 318 SE82 13 X8.0 200 30 X8.0 200 3.9 59 251 251 SE72 13 X7.0 200 30 X7.0 200 3.0 45 192 192 SE62 13 X6.0 200 30 X6.0 200 2.2 33 141 141 Non-structural SL51.5 17 X5.3 150 40 X5.3 150 2.2 32 147 147 SL41.5 17 X4.0 150 40 X4.0 150 1.3 19 84 84
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm. the steel bar after drawing shape as below figure: 1. The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45. The angle scope is greater than 45 and is less than 70, the rib height is from 0.025d to 0.10d. 2. The reinforcing mesh panel includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost. Steel pallet for reinforcing mesh size 2.4m *6m Loading container for reinforcing mesh sheet: 2.4m *6m 3.Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of reinforcing mesh panel has single bars, twin bars or combination of single bars and twin bars. 4.The technical data of reinforcing mesh panle is contained composition and characteristic mechanical porperties of reinforcing steels. Notes: 1. Grade 250N is supplied as plain round reinforcing steel complying with AS 3679. 1, exceptthe tolerance of the diameter and roundness dosen't apply it. 2. For 500L steel bars, only requriement for wire diameter is less than 5.0mm is RekL 500 Material certificate of reinforcing mesh as below: Common size of Squre reinforcing mesh panel for Austialian Market Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6 x2.4 m sheets Cross-sectional area/m width No. x dia., mm Pitch@mm No. x dia., mm Pitch@mm Unit area kg/sqm Sheet, kg Long'l bars sqmm/m Cross bars sqmm/m Squre, with edge side-lapping bars SL102 10 x 9.5 + 4 x 6.75 200100 30 x 9.5 200 5.6 80 354 354 SL92 10 X 8.6 + 4 X 6.0 200100 30 x 8.6 200 4.6 66 290 290 SL82 10 x 7.6 + 4 x 6.0 200100 30 x 7.6 200 3.6 52 227 227 SL72 10 x 6.75 + 4 x 5.0 200100 30 x 6.75 200 2.8 41 179 179 SL62 10 x 6.0 + 4 x 5.0 200100 30 x 6.0 200 2.2 33 141 141 Squre, without edge side - lapping bars SL81 25 X 7.6 100 60 x 7.6 100 7.1 105 454 454 How can we conctrol our products quality for exporting Autralia? Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechanical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3. Secondly, the panel size tolerances measure way as: a. Panel Size dimensions 6m in length, there is 40mm tolerances. b. Panel size dimensions 6m in length, the tolerance is �±0.7% c. Wire diameter and mesh size measure and weld shear resistance test conformance to AS NZS 4761-2001 and as per contract. d. Weigh the each bundle weight to calculate each panel weight.
The slab mesh reinforcement is used on footing construction, beam and piers of waffle rafts. The slab mesh was made by Heyou wire mesh factory accordance with AS NZS 4671-2001. the popular specification is SL102, SL92, SL82, SL72, SL63, SL53, L8TM, L11TM, L12TM in the Australia and New Zealand civil engineeing. The slab mesh reinforcement includes reinforcement mesh and trench mesh. Aoriding to different construction site, they use the spcification of slab meshes are difference. Slab mesh reinforcement for footing slab, beam and piers The full of slab mesh reinforcement specification as below: REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Slab mesh reinforcement for footing slab, beam and piers RIBBED RECTANGULAR MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG RL718 6 x 2.4m Sheet 25 x 6.75 @ 100 30 x 7.60 @ 200 67 RL818 6 x 2.4m Sheet 25 x 7.60 @ 100 30 x 7.60 @ 200 79 RL918 6 x 2.4m Sheet 25 x 8.60 @ 100 30 x 7.60 @ 200 93 RL1018 6 x 2.4m Sheet 25 x 9.50 @ 100 30 x 7.60 @ 200 109 RL1118 6 x 2.4m Sheet 25 x 10.70 @ 100 30 x 7.60 @ 200 130 RL1218 6 x 2.4m Sheet 25 x 11.90 @ 100 30 x 7.60 @ 200 157 Slab mesh reinforcement for footing slab, beam and piers REINFORCING MESH TO AS/NZS4671:2001 / RIBBED SQUARE MESH 6.0 X 2.4 METRES Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL52 6 x 2.4m Sheet 10 x4.77 @ 200 + 4 x 4.00 @ 100 30 x 4.77 @ 200 21 SL62 6 x 2.4m Sheet 10 x 6.00 @ 200 + 4 x 4.24 @ 100 30 x 6.00 @ 200 33 SL72 6 x 2.4m Sheet 10 x 6.75 @ 200 + 4 x 4.77 @ 100 30 x 6.75 @ 200 41 SL82 6 x 2.4m Sheet 10 x 7.60 @ 200 + 4 x 5.37 @ 100 30 x 7.60 @ 200 52 SL92 6 x 2.4m Sheet 10 x 8.60 @ 200 + 4 x 6.00 @ 100 30 x 8.60 @ 200 66 SL102 6 x 2.4m Sheet 10 x 9.50 @ 200 + 4 x 6.75 @ 100 30 x 9.50 @ 200 80 SL81 6 x 2.4m Sheet 25 x 7.60 @ 100 60 x 7.60 @ 100 105 Slab mesh reinforcement for footing slab, beam and piers SQUARE MESH 300 X 300 SPACING TO AS/NZS4671: 2001 Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL53 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 14 SL63 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 21
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Trench mesh reinforcement for footing slab construction and Waffle rafts beam and piers And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
We can supply good quality barbed wire and razor wire for security and fencing uses. Wire Materials: Galvanized steel wire, PVC coated iron wire in blue, green, yellow and other colors. Usage: Barbed Wire mainly serves in protecting of grass boundary, railway, highway and also widely used in military, jail, industry, agriculture, animal husbandry, dwelling house, plantation for fencing. Gauge of Strand and Barb in B.W.G. Approximate Length per Kilo in Meter Barbs Spacing 3" Barbs Spacing 4" Barbs Spacing 5" Barbs Spacing 6" 12x12 6.0617 6.7590 7.2700 7.6376 12x14 7.3335 7.9051 8.3015 8.5741 12-1/2x12-1/2 6.9223 7.7190 8.3022 8.7221 12-1/2x14 8.1096 8.814 9.2242 9.5620 13x13 7.9808 8.899 9.5721 10.0553 13x14 8.8448 9.6899 10.2923 10.7146 13-1/2x14 9.6079 10.6134 11.4705 11.8553 14x14 10.4569 11.6590 12.5423 13.1752 14-1/2x14-1/2 11.9875 13.3671 14.3781 15.1034 15x15 13.8927 15.4942 16.6666 17.5070 15-1/2x15-1/2 15.3491 17.1144 18.4060 19.3386
Steel Reinforcing Mesh Roll is used to provide tensile strength and crack control to structural concrete elements. Steel reinforcing mesh is the thin ribbed wire that can be make rolls presentation. Advantages to save more than 33% of steel, reducing costs 10% -30%; increase the speed of construction can shorten the duration of about 80%; to improve the quality of engineering structures, and concrete bonding anchoring reliable, smooth reinforcement bond strength equal to three times more, and the overall good, deviation is small, anti - cracking performance above 75%. Application Retaining and shear walls Beams and columns Concrete paving overlays Precast concrete elements Suspended floor slabs Swimming pool and gunite construction size(mm) 2.8-5.3 Reinforcement spacing(mm) Longitudinal wire 50-200mm Cross wire 30-1000mm Sheet size Length 2-50m Width 1-1.3m Mechanical and process property Meet GB/T1499.3-2002 standard;AS/NZS 4671; 2001,BS 4483:2005,A185-02
Trench mesh reinforcement is welded by galvanized low carbon steel wire or high quality low carbon steel wire It divided the shape: trapezoid, triangle, two bars and three bars welding. The trench mesh reinforcement is always used on foundation construction, residential slabs, footing construction and pier beam. Specification of trench mesh reinforcement Surface treatment:galvanized or drawn wire Material: R250N, D500N, D500L, D300E, D500E The Tensile strength is 300Mpa. The trench mesh was produced by standard AS NZS 4671-2001 Width: 0.2m - 2.3m Length: 6m REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 And Alls of using is accordance to AS NZS 2870-2011. 1. Footing slap The reinforced footing: the preportions for the tied edge beam apply only where there is a structural connection by concrete-to-concrete contact tied with fitments. The trench mesh is used on bottom reinforcement. The site and the type of construction difference cause we select the specification of the trence mesh reinforcement is different. 2. Waffle rafts beam and piers The waffle rafts for a one-storey building for clad frame or masonry veneer on moderately or highly reactive sites may be supported on piers as follows without structural design of the waffle raft: (a). pier to be located on the intersection of every third internal beam. (b). An additional N12 bar at the top to be provided in the internal beams intersecting the piers, but no shear fitments are required.
Concertina Razor Wire is also named Razor wire or razor type barbed wire. It is a kind of modern security fencing materials with better protection and fencing strength made of hot-dipped galvanized steel sheets or stainless steel sheets. With beautiful and sharp blades and strong core wire, razor wire has the features of secure fencing, easy installation, age resistance and other properties. Concertina Razor Wire is widely used in high-grade residence district, warehouses, prisons and in military fields and other sites requiring severe fencing and security. Razor wire can be classified into straight type razor wire, concertina coils, crossed type and flat type according to the installation models. Outside Diameter No. of Loops Standard Length per Coil Type Notes 450mm 33 8M CBT-65 Single coil 500mm 41 10M CBT-65 Single coil 700mm 41 10M CBT-65 Single coil 960mm 53 13M CBT-65 Single coil 500mm 102 16M BTO-10.15.22 Cross type 600mm 86 14M BTO-10.15.22 Cross type 700mm 72 12M BTO-10.15.22 Cross type 800mm 64 10M BTO-10.15.22 Cross type 960mm 52 9M BTO-10.15.22 Cross type Reference Number Blade Style Thickness Wire Dia Barb Length Barb Width Barb spacing BTO-10 0.5±0.05 2.5±0.1 10±1 13±1 25±1 BTO-12 0.5±0.05 2.5±0.1 12±1 15±1 25±1 BTO-18 0.5±0.05 2.5±0.1 18±1 15±1 35±1 BTO-22 0.5±0.05 2.5±0.1 22±1 15±1 36±1 BTO-28 0.5±0.05 2.5 28 15 46±1 BTO-30 0.5±0.05 2.5 30 18 46±1 CBT-65 0.6±0.05 2.5±0.1 65±2 21±1 101±2
Reinforcing Trench Mesh made from CRB550(550MPa) ribbed wires. The reinforcing trench mesh products all come 6.0m longs, available in 3-Bar, 4-Bar, 5-Bar and 6-Bar, as well as 8, 11 and 12mm wires. Its long, narrow sheets of concrete reinforcing mesh, has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction. Used specifically for residential footing trenches, paths or other narrow spaces. Length m Width m Longitudinal Wires mm Cross Wires mm Mass Kg 6.0 0.2 7.6 @ 100 4.77 @ 300 7 6.0 0.3 7.6 @ 100 4.77 @ 300 9 6.0 0.4 7.6 @ 100 4.77 @ 300 12 6.0 0.5 7.6 @ 100 4.77 @ 300 14 6.0 0.2 10.7 @ 100 4.77 @ 300 13 6.0 0.3 10.7 @ 100 4.77 @ 300 18 6.0 0.4 10.7 @ 100 4.77 @ 300 22 6.0 0.5 10.7 @ 100 4.77 @ 300 27 6.0 0.2 11.9 @ 100 4.77 @ 300 16 6.0 0.3 11.9 @ 100 4.77 @ 300 22 6.0 0.4 11.9 @ 100 4.77 @ 300 27 6.0 0.5 11.9 @ 100 4.77 @ 300 33
Concrete welded Reinforcing mesh is a welded wire fabric, prefabricated steel reinforcement material. It has a rectangular or square grid pattern and is produced in flat sheets. The fabric is used to provide tensile strength and crack control to structural concrete elements. Advantages: Concrete Welded mesh reinforcingis a convenient and cost effective alternative to conventional bar reinforcement for the following reasons : The mesh is generally specified and manufactured according to standard references making for easy site identification, quality control and management. The mesh is manufactured in sheets or rolls resulting in a quick and simple site installation process. Although generally used in surface beds (concrete floor slabs on fill) and concrete roads, mesh can also be used in suspended floor slabs, concrete walls, culverts / drains and composite brick / concrete retaining walls. Square Reinforcing Mesh Standard Sheets - 6 m (length) x 2.4 m (width) = 14.4 m²: REFERENCE MAIN WIRE(mm) CROSS WIRE(mm) EDGE WIRE(mm) MASS(kg) SL81 7.60@100 7.60@100 7.60@100 105 SL102 9.50@200 9.50@200 9.50@200 80 SL92 8.55@200 8.55@200 8.55@200 65 SL82 7.60@200 7.60@200 7.60@200 52 SL72 6.75@200 6.75@200 6.75@200 40 SL62 6.00@200 6.00@200 6.00@200 33 SL52 4.75@200 4.75@200 4.75@200 21 Rectangular Reinforcing Mesh Standard Sheet - 6 m (length) x 2.4 m (width) = 14.4m². REFERENCE MAIN WIRE(mm) CROSS WIRE(mm) MASS(kg) RL718 25*6.75@100 30*7.60@200 68 RL818 25*7.60@100 30*7.60@200 79 RL918 25*8.55@100 30*7.60@200 93 RL1018 25*9.50@100 30*7.60@200 109 RL1118 25*10.65@100 30*7.60@200 131 RL1218 25*11.90@100 30*7.60@200 157
Concrete Reinforcing Mesh Panel also called: Steel Bar Welded Wire Mesh /reinforcing welded mesh panel,cold ribbed steel bar mesh,welded wire mesh. Material: steel bar Weaving: the wires that run parallel to the width of the roll are placed on top of the wires running parallel to the length. Then, the wires are welded where they intersect. Wire diameter: welded steel bar panels ranges from 5mm to 16mm. Applications: Welded steel bar panels are widely used in construction reinforcement, the ground for the tunnels, bridges, highway, airport and wharf, also in construction of wall body. Features: Solid construction, Easy handling Packing: PVC Shrink, Moister-proof paper, Carton, pallet, Wooden Box , Special packing can be arranged upon request
The slab mesh reinforcement is used on footing construction, beam and piers of waffle rafts. The slab mesh was made by Heyou wire mesh factory accordance with AS NZS 4671-2001. the popular specification is SL102, SL92, SL82, SL72, SL63, SL53, L8TM, L11TM, L12TM in the Australia and New Zealand civil engineeing. The slab mesh reinforcement includes reinforcement mesh and trench mesh. Aoriding to different construction site, they use the spcification of slab meshes are difference. The full of slab mesh reinforcement specification as below: REINFORCING MESH TO AS/NZS4671: 2001 / TRENCH MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG L8TM200 6 Metre 3 x 7.60 @ 100 4.00 @ 300 6.8 L8TM300 6 Metre 4 x 7.60 @ 100 4.00 @ 300 9.2 L8TM400 6 Metre 5 x 7.60 @ 100 4.00 @ 300 11.6 L8TM500 6 Metre 6 x 7.60 @ 100 4.00 @ 300 13.9 L8TM600 6 Metre 3 x 7.60 @ 100 4.00 @ 300 15.9 L8TM2400 6 Metre 25 x 7.60 @ 100 4.00 @ 300 72 L11TM200 6 Metre 3 x 10.70 @ 100 4.77 @ 300 13 L11TM300 6 Metre 4 x 10.70 @ 100 4.77 @ 300 17.7 L11TM400 6 Metre 5 x 10.70 @ 100 4.77 @ 300 22.3 L11TM500 6 Metre 6 x 10.70 @ 100 4.77 @ 300 26.8 L11TM600 6 Metre 7 x 10.70 @ 100 4.77 @ 300 34 L11TM2300 6 Metre 24 x 10.70 @ 100 4.77 @ 300 107.1 L12TM200 6 Metre 3 X 11.90 @ 100 4.77 @ 300 16.3 L12TM300 6 Metre 4 X 11.90 @ 100 4.77 @ 300 21.8 L12TM400 6 Metre 5 X 11.90 @ 100 4.77 @ 300 27.3 L12TM500 6 Metre 6 X 11.90 @ 100 4.77 @ 300 32.8 L12TM600 6 Metre 7 X 11.90 @ 100 4.77 @ 300 38.1 Slab mesh reinforcement for footing slab, beam and piers RIBBED RECTANGULAR MESH Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG RL718 6 x 2.4m Sheet 25 x 6.75 @ 100 30 x 7.60 @ 200 67 RL818 6 x 2.4m Sheet 25 x 7.60 @ 100 30 x 7.60 @ 200 79 RL918 6 x 2.4m Sheet 25 x 8.60 @ 100 30 x 7.60 @ 200 93 RL1018 6 x 2.4m Sheet 25 x 9.50 @ 100 30 x 7.60 @ 200 109 RL1118 6 x 2.4m Sheet 25 x 10.70 @ 100 30 x 7.60 @ 200 130 RL1218 6 x 2.4m Sheet 25 x 11.90 @ 100 30 x 7.60 @ 200 157 Slab mesh reinforcement for footing slab, beam and piers REINFORCING MESH TO AS/NZS4671:2001 / RIBBED SQUARE MESH 6.0 X 2.4 METRES Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL52 6 x 2.4m Sheet 10 x4.77 @ 200 + 4 x 4.00 @ 100 30 x 4.77 @ 200 21 SL62 6 x 2.4m Sheet 10 x 6.00 @ 200 + 4 x 4.24 @ 100 30 x 6.00 @ 200 33 SL72 6 x 2.4m Sheet 10 x 6.75 @ 200 + 4 x 4.77 @ 100 30 x 6.75 @ 200 41 SL82 6 x 2.4m Sheet 10 x 7.60 @ 200 + 4 x 5.37 @ 100 30 x 7.60 @ 200 52 SL92 6 x 2.4m Sheet 10 x 8.60 @ 200 + 4 x 6.00 @ 100 30 x 8.60 @ 200 66 SL102 6 x 2.4m Sheet 10 x 9.50 @ 200 + 4 x 6.75 @ 100 30 x 9.50 @ 200 80 SL81 6 x 2.4m Sheet 25 x 7.60 @ 100 60 x 7.60 @ 100 105 Slab mesh reinforcement for footing slab, beam and piers SQUARE MESH 300 X 300 SPACING TO AS/NZS4671: 2001 Code STD UNIT LONGITUDINAL WIRES CROSS WIRES MASS / KG SL53 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 14 SL63 6 x 2.4m Sheet 6 x 5.00 @ 300 20 x 5.00 @ 300 21
Reinforcing mesh was made by deformed bar after drawn, which is accorded to Australian/New Zealand Standard AS-NZS 4671-2001. The material is 250N, 300E, 500L, 500N and 500E, the mesh spaces is 200mm, there is two sides overhang which is 100mm. 1. The angle of the rib or inclined indentation of the reinforcing mesh panels' bar isn't less than 45°. The angle scope is greater than 45° and is less than 70°, the rib height is from 0.025d to 0.10d. 2. The reinforcing mesh panel includes transverse and longitudinal bar, pitch and overhang. The Australian and new zealand's market, the normal panel size is 2.4m*6m.Because of containers size, we always advise our cutomer to make the panel size to be 2.2m*5.8m. It can be easy to be load and save more USD1000 per container for packing and loading cost. 3.Each sheet of reinforcing mesh panel shall include number of bars,pitch,length,width, and overhang dimensions. And the bar arrangement of reinforcing mesh panel has single bars, twin bars or combination of single bars and twin bars. 4.The technical data of reinforcing mesh panle is contained composition and characteristic mechanical porperties of reinforcing steels. Common size of Squre reinforcing mesh panel for Austialian Market Mesh Type and reference number Longitudinal bars Cross-bars Mass for 6 x2.4 m sheets Cross-sectional area/m width No. x dia., mm Pitch@mm No. x dia., mm Pitch@mm Unit area kg/sqm Sheet, kg Long'l bars sqmm/m Cross bars sqmm/m Squre, with edge side-lapping bars SL102 10 x 9.5 + 4 x 6.75 200100 30 x 9.5 200 5.6 80 354 354 SL92 10 X 8.6 + 4 X 6.0 200100 30 x 8.6 200 4.6 66 290 290 SL82 10 x 7.6 + 4 x 6.0 200100 30 x 7.6 200 3.6 52 227 227 SL72 10 x 6.75 + 4 x 5.0 200100 30 x 6.75 200 2.8 41 179 179 SL62 10 x 6.0 + 4 x 5.0 200100 30 x 6.0 200 2.2 33 141 141 Squre, without edge side - lapping bars SL81 25 X 7.6 100 60 x 7.6 100 7.1 105 454 454 How can we conctrol our products quality for exporting Autralia? Firstly, we purchase the material from Steel Factory and inspect chemical composition and mechnical property of reinforcing mesh panel in our in-house laboratary according to AS 1554.3. Secondly, the panel size tolerances meassure way as: a. Panel Size dimensionsâ?¤6m in length, there is 40mm tolerances. b. Panel size dimensionsï¼?6m in length, the tolerance is ±0.7% c. Wire diameter and mesh size measure and weld shear resistance test conformance to AS NZS 4761-2001 and as per contract. d. Weigh the each bundle weight to calculate each panel weight.
Anping Tenglu Metal Wire Mesh Co.,LTD Stainless Steel 304 Decorative Mesh Product Description: Decorative mesh has been adopted more and more by the building field whatever on the material, structure or style because its beautiful metal color, concise style, good function, fashion and other more decorative elements. We can provide woven stainless steel wire mesh for architecture & decorations. Woven wire fabrics come in beautiful and unique designs, and these products are used mainly as decorative coverings for the whole buildings, walls, ceilings or floors. Materials:Made of stainless steel 304, 316 and 316L. Feature:Lasting, beautiful, being full of modern sense. Application: Wire mesh facades; Shade screens; Architecture ceilings; Metal draperies for walls, partition and isolation screens; Staircases isolation screen, elevator cabins screen; Floor covering fabrics; Other special uses.
Anping Tenglu Metal Wire Mesh Co.,LTD Welded Steel Bar Grating Welded steel bar grating is the most popular of all grating types due to its strength, cost-efficient production and ease of installation. Steel bar grating costs less time and labor in work. It saves about 50 to 70 percent work time compared with common binding wire mesh. The use of bar grating can also strengthen the concrete parts to reduce surface breaking ratio. Welded bar grating for reinforcement is especially suitable for big area concrete engineering. Using of welded bar reinforcement can save about 10 percent of the total cost of the project. It is also ideal for use as mezzanine decking since it supports the same loads as comparable solid flooring.More than that, its cost saving openness maximizes the circulation of air, light, heat, water and sound, while promoting cleanliness. And, where insurance codes permit, additional sprinklers can often be eliminated.Standard panels are available in widths of 2', 3' or 4'. Welded steel bar grating is resistance welded to create a rugged, one piece constructed panel. The bearing bars are automatically resistance welded at the contact point with the cross bars and, under a combination of high heat and pressure, are fused together to form a permanent joint.The cross bars provide a high degree of rigidity, yet retain a smooth flat surface for free and easy walking. Welded steel bar mesh panels have three types: black steel bar welded wire mesh, galvanized steel bar welded wire and hot dipped galvanized steel bar welded wire mesh. Welded steel bar panels are widely used in making of floors, ceilings, wall body, concrete road, bridge surface, airport, tunnel lining, concrete piping, etc. Specification: Wire Diameter: 5-16mm. Horizontal Spacing: 50.100.200.300.400mm. Vertical Spacing: 50-600mm. Panel length:1000-14000mm. Panel width:100-300cm
Anping tenglu metal wire mesh co.Ltd Brick mesh Brick mesh is a kind of mesh panel dedicated for concrete and it can be divided into two types, one is welded cold-drawn low carbon steel wire and the other is galvanized after welded. Brick mesh is widely used in the large-area plastering engineering as the plastering underlay, in order to avoid cracking and resist vibrations. The column is made of concrete and has low costs, low intensity and and high stability. The colored coating is corrosion resistant and decorative impression. The brick mesh looks harmonious and beautiful. It has the continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction
