LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator For more , please kindly feel free to contact
LC120 thermal silicone pad is a very cost-effective general economic thermal gap filling gasket, soft with its own micro-stick, easy assembly. Under low compressing force to show good thermal conductivity and electrical insulation properties. Bedding on the gap between the heat device and the heat sink or the machine shell to extrude air to reach the full contact forming a continuous thermal conduction. Using heat sink or machine shell as a cooling device can effectively increase the cooling area to achieve a good cooling purposes. Features & Benefits: Low cost, high efficiency, cost-effective Replace the volatile pollution of the thermal grease Natural sticky, easy to install, can be reused Wide range of thickness, can fill any uneven size gap Electrical insulation Typical Applications: Communication equipment New energy vehicles / power batteries Computer Car equipment / charger Switching power supply PC server / workstation Flat-panel TV Optical drive / COMBO Security equipment Notebook computers Video equipment Any heating element and radiator Physical Properties: Test Item Test Method Unit LC120 Color Visual - Off white Thickness ASTM D374 mm 0.3~15.0 Hardness ASTM D2240 Shore 00 40±5~80±5 Specific Gravity ASTM D792 g/cm3 2.1 Tensile Strength ASTM D412 Mpa 0.34 Elongation ASTM D412 % 100 Tear Strength GBT 529-2008 KN/m 1.4 Breakdown Voltage ASTM D149 KV/mm â?¥10 Volume Resistivity ASTM D257 Ω·cm 8Ã?1012 Continuous Use Temp EN344 -40~150 Flame Rating UL 94 - V-0 Weight Loss @150240H % â?¤0.5% Dielectric Constant ASTM D150 @1MHz 5.41 Thermal Conductivity ASTM D5470 W/m·K 1.2 Standard sizeï¼?200mmÃ?400mmï¼?300mmÃ?400mmï¼?Customized size available; Coated with fiberglass/one side or double side adhesive/aluminum foil available
Ultra-high thermal conductive silicone sheet is a high-performance heat conducting interface material made of 100% imported materials for fillingthe air gaps between the heating device and the heat sink or metal base.Its softness and elasticity characteristics enable it to be used for coveringa very uneven surface. Heat is transferred from the separation device or the entire PCB to the metal casing or diffuser to improve heat dissipationand improve the efficiency of heating electronic components and service Features & Benefits: High thermal conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect sensitive electronic devices Natural sticky, easy assembly, re-workable Meet ROHS and UL environmental requirements Typical Applications: CPU, memory module Communication hardware equipment High-speed hard disk drive Automotive engine control module Microprocessors, memory chips and graphics processors Military electronic equipment For more , please kindly feel free to contact
High thermal conductive silicone pad is a high thermal conductivity material. The raw material is made of Japan Electrochemical High Thermal Conductive Spherical Alumina Powder and Dow Corning Polymer. It is a cost-effective thermal gap filling material. The surface's natural micro-viscosity and softness can well fill the air gaps to transfer the heat between the heat source and the heat sink to improve heat dissipation and improve the efficiency of heating electro-nic components and service life. It is an ideal thermal interface material. Benefits: Cost-effective, high conductivity, low thermal resistance Soft and flexible, reducing the interface thermal resistance High electrical insulation to protect electronic devices Natural sticky, easy application, reworkable Meet ROHS and UL environmental requirements Applications: High thermal conductivity module new energy vehicles Microprocessors, memory chips and graphics processors Network communication equipment Car equipment, charger High-speed hard disk drive For more , please kindly feel free to contact
LCG is a kind of thermal interface material which coating thermal conductive polymer on a layer of fiberglass. The stickiness of the material is slightly weakness for easy procession. And insulation and tear resistance are also better. Its stickiness and flexibility, even in extremely rough and very uneven surface, also can bring a good thermal filling effect. Features & Benefits: Fiberglass substrate, anti-puncture, shear and tear resistance Only the bottom with a sticky, slightly faint on the front, easy to install High-load, low-hardness gap filling material Strong electrical insulation Typical Applications: AC / DC power supply Car equipment / charger Between the motherboard and the chassis Drive control any heating element Uninterruptible power supply (UPS) Power semiconductor-TO packaging products
LGS1500 is a synthetic graphite heat sink.LGS1500 has an unique grain orientation, lamellar structure can be well adapted to any surface, even heat conduction along the two directions. Plane thermal conductivity of up to 1900W/m-K. LGS1500 products while also the thickness of uniform heat to provide thermal isolation. Heat shielding and components while improving the performance of consumer electronics products. LGS1500 composite graphite sheet is a polyimide sintered novel film material with high thermal conductivity and excellent product design flexibility. Features & Benefits: 1.High thermal conductivity -flat heat conductivity can be up to1900W /m-K,40% lower thermal resistance than aluminum, 20% lower than copper 2.Ultra-light -than the same size aluminum to 30%lighter, 80%lighter than copper 3.Thin -thickness from 0.017 �?0.025mm and 0.04mm 4.Temperature resistance-using temperature up to 400, the minimum can be lower than-40 5.Easy processing-can be made into different die sizes, shapes and thickness, can provide planar sheet die 6.Ease of use-graphite heat sink can be applied to any smooth flat and curved surfaces 7.Flexibility- easily with the metal, the insulating layer or double-sided adhesive made of plywood, increase design flexibility in the back with adhesive For more , please kindly feel free to contact
LGS1500 is a synthetic graphite heat sink.LGS1500 has an unique grain orientation, lamellar structure can be well adapted to any surface, even heat conduction along the two directions. Plane thermal conductivity of up to 1900W/m-K. LGS1500 products while also the thickness of uniform heat to provide thermal isolation. Heat shielding and components while improving the performance of consumer electronics products. LGS1500 composite graphite sheet is a polyimide sintered novel film material with high thermal conductivity and excellent product design flexibility. Features & Benefits: 1.High thermal conductivity -flat heat conductivity can be up to1900W /m-K,40% lower thermal resistance than aluminum, 20% lower than copper 2.Ultra-light -than the same size aluminum to 30%lighter, 80%lighter than copper 3.Thin -thickness from 0.017 ï¼?0.025mm and 0.04mm 4.Temperature resistance-using temperature up to 400, the minimum can be lower than-40 5.Easy processing-can be made into different die sizes, shapes and thickness, can provide planar sheet die 6.Ease of use-graphite heat sink can be applied to any smooth flat and curved surfaces 7.Flexibility- easily with the metal, the insulating layer or double-sided adhesive made of plywood, increase design flexibility in the back with adhesive For more , please kindly feel free to contact
Thermal interface material , thermal conductive silicone rubber pads , thermal grease , thermal insulator , phase change material , thermal tap gap filler , liquid gel filling gap.Manufacturer
LCK-10 silicon pad is a high-performance insulating material substrate of Kapton membrane coating with silicone and has good thermal conductivity and anti-pierce.LCK-10 is designed For those ceramic insulator substitutes like beryllium oxide�??boron nitride and bauxite. As we know that ceramic insulators very expensive and easy broken,however,LCK-10 is hard To broke and the price of it is low. Features & Benefits: Heat emission, insulation , fire prevention, shock resistance. Thermal impedance: 0.41-in2/w(50psi) Breakdown voltage can reach at 7000V Designed for the substitutes of the ceramic insulators Typical Applications: Heating power components; Automobile electronic heating module; Power module; Household appliances;
LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL. Typical Applications High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost. Applying Process 1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil. 2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural. 3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected. For more , please kindly feel free to contact
LT240 Alumina oxide ceramic plate has a high thermal conductivity : 24w/m.k, it is of simple construction and small volume, but it can resist acid and alkali corrosion, work in high temperature and pressure and of stable performance for a long time.0.635mm, 1.0mm, 2.0mm, 3.0mm, 4.0mm can be offered for TO-220, TO-247, TO-264, TO-3P sizes, customized size is available, ROHS is compliant. Typical applications IC, MOS, transistor, schottky, IGBT, high density switch power supply, HF communications equipment and brazing machine. For more , please kindly feel free to contact
LCE series gel is a thermal conductive material with extremely low deformation rate. Its plasticity like plasticine, no flow, high thermal conductivity, low thermal resistance, good adhesion to heat-dissipating components, insulation, automatically fill the gap, maximum increase of limited contact area, and the infinite compression feature is suitable for heat dissipation modules or electronic components with large thickness variation. Unlike thermal grease, the thermal gel wont settlement and flow. It is suitable for screen printing or blade coating. The syringe package can be dispensed on standard dispensing equipment, which has high operation convenience and efficiency. Features & Benefits: High thermal conductivity, low thermal resistance, excellent wettability; Soft, unstressed, with infinite compression of the thinnest 0.1mm; No settlement, no flow, can fill any uneven gap; The design is convenient and can be used to adjust the size of any thickness. Typical Applications: Communication equipment Radio equipment Automotive electronics Case or related cooling module Mainframe and small office networking equipment For more , please kindly feel free to contact
LT1800 Aluminum nitride conductive ceramic sheet has high thermal conductivity 180W/m-k,one of the highest thermal conductivity materials in metallic materials (7~10 times of alumina ceramic sheet). Excellent mechanical properties, good processing, high precision, smooth surface, no microcracks, bending, etc. Low dielectric constant and dielectric loss, reliable electrical insulation performance. Non-toxic, high temperature of 1800 degrees, oil resistant, chemical resistant, and similar to the thermal expansion coefficient of silicon, without hygroscopic property, stable performance and high reliability in high temperature and high humidity. Along with the microelectronic devices, Features & Benefits: Extremely high thermal conductivity High temperature and high humidity Good insulation Good chemical stability Typical Applications: Application of optical communication devices High frequency microwave application Power electronic components LED industry Car electronic module The thermal module substrate For more , please kindly feel free to contact
LP900 is a silicon carbide ceramic heat sink and it belongs to the micro-hole structure. Under the same unit area,it can be more than 30% porosity, greatly increasing the heat transfer area with air to enhance its cooling effect. At the same time its heat capacity is small, its heat storage is small and the heat can be more quickly to the outside world. Ceramic heat sink main features: environmental protection, insulation resistance to high pressure, efficient heat, to avoid brewing EMI problems. So it can effectively solve the electronic and home appliance industry thermal and cooling problems, while it is specially for small and medium wattage power consumption, design space pay attention to light, thin, short, small products. Whats more, it can provide technical support and application for electronic products innovative and development. For more , please kindly feel free to contact
LP900 is a silicon carbide ceramic heat sink and it belongs to the micro-hole structure. Under the same unit area,it can be more than 30% porosity, greatly increasing the heat transfer area with air to enhance its cooling effect. At the same time its heat capacity is small, its heat storage is small and the heat can be more quickly to the outside world. Ceramic heat sink main features: environmental protection, insulation resistance to high pressure, efficient heat, to avoid brewing EMI problems. So it can effectively solve the electronic and home appliance industry thermal and cooling problems, while it is specially for small and medium wattage power consumption, design space pay attention to light, thin, short, small products. Whats more, it can provide technical support and application for electronic products innovative and development. For more , please kindly feel free to contact
LE series thermal grease has good thermal conductive performance and reliability and can wet the surface of copper and aluminum which is extremely suit for the heat transfer of the CPU, GPU and other heating power components. As LE series has low adhesion, can fully wet the surface, form very low surface thermal resistance, it can quickly transfer the heat to cooling device. Just paste the grease on the gap between the power components and cooling device to help dismiss the air gap and enlarge the heat flow, decrease thermal resistance, reduce the temperature of power components, improve reliability and extend the usage life Typical Applications: Between Semiconductor and heatsink Between CPU and heatsink Between power resistor and base Thermoelectric cooler The surface of temperature regulator and assembly High-power LED lighting For more , please kindly feel free to contact
LT240 Alumina oxide ceramic plate has a high thermal conductivity : 24w/m.k, it is of simple construction and small volume, but it can resist acid and alkali corrosion, work in high temperature and pressure and of stable performance for a long time.0.635mm, 1.0mm, 2.0mm, 3.0mm, 4.0mm can be offered for TO-220, TO-247, TO-264, TO-3P sizes, customized size is available, ROHS is compliant. Typical applications IC, MOS, transistor, schottky, IGBT, high density switch power supply, HF communications equipment and brazing machine. For more , please kindly feel free to contact
Polycarbonate PC-insulation mylar is the plastic material by calendaring molding technology, with excellent flame rating V0, halogen-free environment protection, aging resistance, good mechanical properties and electrical insulation performance. Black color, matte side of the light / matte. Standard thickness: 0.1,0.15,0.25,0.43,0.5 MM Features & Benefits: Insulation resistance. No bromine chloride. Flame Rating V-0. Excellent mechanical properties and temperature resistance, stable size Typical Applications: Electrical insulation for power products. TV insulation. Insulated from the enclosure to PCB Insulation of inductance, resistance, capacitance and other parts. High voltage requirement occasion For more , please kindly feel free to
LT1800 Aluminum nitride conductive ceramic sheet has high thermal conductivity 180W/m-k,one of the highest thermal conductivity materials in metallic materials (7~10 times of alumina ceramic sheet). Excellent mechanical properties, good processing, high precision, smooth surface, no microcracks, bending, etc. Low dielectric constant and dielectric loss, reliable electrical insulation performance. Non-toxic, high temperature of 1800 degrees, oil resistant, chemical resistant, and similar to the thermal expansion coefficient of silicon, without hygroscopic property, stable performance and high reliability in high temperature and high humidity. Along with the microelectronic devices, Features & Benefits: Extremely high thermal conductivity High temperature and high humidity Good insulation Good chemical stability Typical Applications: Application of optical communication devices High frequency microwave application Power electronic components LED industry Car electronic module The thermal module substrate For more , please kindly feel free to contact
LGS300 graphite thermal pad is a new thermal interface material. It transfers heat along the two directions, shielding heat source and components meanwhile improving the performance of consumer electronics products. The thermal impedance of LGS is very small and can completely replace the high-performance thermal grease while avoiding the shortcoming of poor and dirty thermal grease process. LGS thermal conductivity is three-dimensional, that is not only it can transfer heat between the heat source and the radiator in the vertical direction, but also in the vertical direction, which ensures that it can quickly transfer heat out in vertical direction when the partial heat is high. Therefore, LGS thermal film is very suitable in the small space to efficiently transfer heat generated by heat source. Features & Benefits: Ultra-high thermal conductivity, easy to operate; Low thermal resistance Light weight Typical Applications: IC ; CPU; MOS; LED; Heat sink; LCD-TV; Laptop; Communication equipment; Wireless switch; DVD; Hand-held device; Camera/digital camera; Mobile phone For more , please kindly feel free to contact
