DL-1 model electric air heater with upper inlet and lower outlet is consists of 4 parts: stainless steel electric heating finned tubes + insulation box + fan + control system. The electric heating groups start sequentially to convert electrical energy into heart. And heating the fresh air entering the box at a setting temperature, then blow out by fan.
4ã??Advantages/features
1. Simple structure, beautiful appearance, low cost
2. Stainless steel electric heating finned tube, durable
3. Automatic start and close, precise temperature control, energy saving, low load
4. Large air volume and small wind temperature fluctuation
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
DL-2 model electric air heater with Left-Right Circulation is consists with 6 parts: electric heater + inner tank + insulation box + fan +fresh air damper + control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by electric heater. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place.
Advantages/features
1. Simple structure and easy installation
2. Large air volume and small wind temperature fluctuation
3. Stainless steel electric heating finned tube, durable
4. Automatic control system, group start and close, low load, precise temperature control
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
7. left and right fans run alternately in cycles to ensure even heating
8. Automatically replenish fresh air
ZL-1 model Steam air heater with upper inlet and lower outlet is consists of 6 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + electric control system. Steam passes the though the fin tube, dissipating heat to the insulation box, mixing and heating the fresh or recycle air to setting temperature, fans bring this hot air into drying room or heating room to be used for dehydration, dehumidification or heating.
4. Advantages/features
1. Simple structure, beautiful appearance, low cost
2. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable;
3. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature.
4. Large air volume and small wind temperature fluctuation
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
ZL-2 model steam air heater with Left-Right Circulation is consists of 7 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan+ Fresh air damper + electric control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by steam heater. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place.
1.Simple structure and easy installation
2. Large air volume and small wind temperature fluctuation
3ï¼?Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable;
4. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature.
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
7. left and right fans run alternately in cycles to ensure even heating
8. Automatically replenish fresh air
ZL-3 model steam air heater with upper outlet and lower inlet is consists of 9 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + Fresh air damper + waste heat recovery device + dehumidification fan + electric control system. It is specially designed for supporting downflow drying room/heating rooms. After convert the outside steam heat to heat inside the insulation box through by the fin tube, it�´s mixing with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system.
Advantages/features
1. Simple structure and easy installation
2. Large air volume and small wind temperature fluctuation
3. Stainless steel electric heating finned tube, durable
4. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable;
5. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature.
6ï¼?High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device.
8. Automatically replenish fresh air
TL-1 burning furnace is consists of 5 parts: natural gas burner + inner tank + insulation box + fan + control system. The burner forms a high-temperature flame after full combustion in the high-temperature resistant inner tank, these flame mixes with the cold or recirculated air to produce a new and high-temperature air. Under the action of the fan, it is discharged to provide heating for drying machines or places.
Advantages/features
1. Simple structure and low cost
2. Large air volume and small wind temperature fluctuation
3. Stainless steel high temperature resistant inner tank, durable
4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic),
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
TL-2 model Direct burning furnace is consists of 6 parts: natural gas burner + inner tank + insulation box + fan +fresh air damper + control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by full combustion of natural gas. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place.
4. Advantages/features
1. Simple structure and easy installation
2. Large air volume and small wind temperature fluctuation
3. Stainless steel high temperature resistant inner tank, durable
4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic),
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
7. left and right fans run alternately in cycles to ensure even heating
8. Automatically replenish fresh air
TL-3 model Direct burning furnace with lower Inlet and upper outlet is consists of 8 parts: natural gas burner + inner tank + insulation box + fan + fresh air damper + waste heat recovery device + dehumidification fan + control system. It is specially designed for supporting downflow drying room/heating rooms. After fully combusts the natural gas inside the inner tank, it�´s mixed with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system.
4. Advantages/features
1. Simple structure and easy installation
2. Large air volume and small wind temperature fluctuation
3. Stainless steel high temperature resistant inner tank, durable
4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic),
5. High-density fire-resistant rock wool insulation box to avoiding heat loss
6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device.
8. Automatically replenish fresh air
TL-4 model Direct burning furnace with 3 layers sleeve consists of 3 layers of cylinders. It uses fully burned natural gas to obtain high-temperature flame, and mixing this temperature with fresh air to achieve the required hot air device. Due to the use of fully automatic single-stage fire, two-stage fire or modulating burner, the output hot air is extremely clean by natural gas fully burned, , meeting the drying and dehydration needs for most stuffs. The external fresh air enter the furnace body under negative pressure, takes two strokes and sequentially cools the middle cylinder and the inner tank. After being fully mixed with the high-temperature flame in the mixing zone, it is extracted from the furnace body and enter the drying room. When the temperature reach the setting number, the main burner stops working and the auxiliary burner continues to burn to maintain the temperature. When the temperature drops to the set lower limit temperature, the main burner will be run again.
4ã??Advantages/features
1. Simple structure and easy installation
2. Small air volume, high temperature, adjustable from normal temperature to 500â??
3. Stainless steel high temperature resistant inner tank, durable
4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic),
5. The fresh air has a long stroke that can fully cool the inner tank, so the outer tank can be touched without insulation.
6. Equipped with high temperature resistant centrifugal fan, large pressure center and long lift
TL-5 model Indirect burning furnace with 5 layers sleeves consists of 5 parts: a blower, flue gas induced draft fan, burner, five-layer sleeve body and control system. The flue gas in the furnace takes two rounds while the fresh air takes three rounds.
Natural gas is burned through the burner to generate a high-temperature flame. Under the action of the flue gas fan, the heat is transferred to the heated air through the five-layer sleeve wall and dense fins, meanwhile the flue gas is discharging out the body after it´s temperature down to 150. The heated fresh air enter the sleeves through blower. After heat mix, the temperature rises to the setting number and sent out from the hot air outlet.
4ã??Advantages/features
1. Continuously provide pure air with constant temperature and constant pressure.
2. Temperature has a wide adjustable range: 40~300
3. Indirect heating, automatic operation, exhaust gas emissions meet the requirements
4. Reasonable design, compact structure, thermal efficiency up to 75%
5. Stainless steel high temperature resistant inner tank, durable
