A? Project: Led bulb aging line machine
B? Specifications : 12000l×1000w×800h(mm)
C? Quantity : One set
D? Structure : Ring chain conveying, chain boards holder aging, frequency control of motor speed
E? Function and feature : This equipment is professional for led bulbs inspection. Through high voltage, normal voltage, low voltage, roaming and fluctuation voltage, impact functions. High temperature zones to observe whether short-circuit, capacitance burst and black points will occur. Also used for inspecting the simulation daily use of led lamp cycling circuit and roaming seasoning area. Easy to cooperate.
F? Specifications :
1. Motor : Adopt 1500w motor, wps80 type 1:60 of the speed reducer, the domestic well-known brand 2 hp's island converter, frequency conversion step less speed regulation, linear speed0.3—2m/min can be adjusted.
2. Machine body and strand : Made of 40×40 rectangle steel pipe by welding. Upper and lower body side protection using special aluminum alloy aging line dedicated. Protective board is made of 1.2mm cold steel sheet by bending. Support legs are equipped with galvanized adjustable soles.
3. Conveying chain: Double-pitch single-side-ear double-hole chain manufactured by shanghai chain factory, 1.5m long.
4. Chain plate: Made of 2mm thick 800×148×15mm cold rolling sheet, total 140 plates.Each plates for 12pcs of b22 bulbs . And equipped with high marks broken small circuit breaker. Road conductive bottom of the chain plate mounting system(copper), each installation of two conductive blocks, each plate were installed 2.
5. Daily output: The aging line once can aging1680pcs led bulbs. The aging time for one hour. One day can work 10 hours. Total daily output is 16800pcs of led bulbs one day.
6. Stop light shield: On both sides edges of the seven sections equipped a stop light shield plastic plates, using 4mm tawny organic glass plate and 40x40 aluminum alloy combinations and become effective damping light intensity to your eyes, better protect your eyes.
A? Project: LED tube light (fluorescent) aging line machine
B? Specifications : 12000L×1540W×800H(mm)
C? Quantity : One set
D? Structure : Ring chain conveying, chain boards holder aging, frequency control of motor speed
E? Function and feature : This equipment is professional for LEDT8 tube light inspection. Through high voltage, normal voltage, low voltage, roaming and fluctuation voltage, impact functions. High temperature zones to observe whether short-circuit, capacitance burst and black points will occur. Also used for inspecting the simulation daily use of LED lamp cycling circuit and roaming seasoning area. Easy to cooperate.
F? S pecifications:
1. Motor : adopt 1500w motor, WPS80 type 1:60 of the speed reducer, the domestic well-known brand 2 HP's island converter, frequency conversion step less speed regulation, linear speed0.3—2M/min can be adjusted.
2. Machine body and strand : Made of 40×40 rectangle steel pipe by welding. Upper and lower body side protection using special aluminum alloy aging line dedicated. Protective board is made of 1.2mm cold steel sheet by bending. Support legs are equipped with galvanized adjustable soles.
3. Conveying chain: Double-pitch single-side-ear double-hole chain manufactured by Shanghai Chain Factory, 1.5m long.
4. Chain plate: Made of 2mm thick 1350×148×15mm cold rolling sheet, total 140 plates.. And equipped with high marks broken small circuit breaker. Road conductive bottom of the chain plate mounting system(copper), each installation of two conductive blocks, each plate were installed 2.
5. Daily output: The aging line once can also aging 560pcs T8 tube lamp . The aging time for one hour. One day can work 10 hours. Total daily output is 5600pcs LED tube lamp one day.
6. Stop light shield: On both sides edges of the seven sections equipped a stop light shield plastic plates, using 4mm tawny organic glass plate and 40X40 aluminum alloy combinations and become effective damping light intensity to your eyes, better protect your eyes.
7. Conductive slot: Up and down with all conduction channel rail, the insulating rubber sheet, and assembly stainless steel electric tank.
8. Constant temperature area: Complete thermostatic system USES electric heating type, set for a period of two pieces of 2000 w/set of electro thermal heating plate, automatic constant temperature at room temperature - 60 ?, digital temperature control instructions.
Dimension : 12000L×1450W×730H(mm)
Quality : One set
Structure : Automatic chain conveying ,Tooling plate conveying
Function and features:: This equipment is suitable for all kinds of LED street lamps and electronic
electrical appliances manufacturer, specialized in water assembly, the
power system using variable frequency speed control system, stable
performance, safety and reliability, simple operation.
Specification :
1. Driver device: Adopt 1.5 KW / 380 v motor, reducer
adopts 100 # 1:6 0, speed 1-5 M/minutes adjustable, PLC
control, head support using 40 x 40 x§2.0mm carbon steel
flat pass welding and into production, head seal plate using
§1.5mm A3 plate bending production.
2. Guide : Guide adopt 100 x 118 mm special aluminum guide rail, rail
link adopt A3 plate production , plastic-sprayed surface
treatment;
3. Transfer chain : Adopt Suzhou quality P = 38.1mm three times the speed chain, the whole
line arrangement;
4. Frame or skeleton: Adopt 40x40x§2.0 mm carbon steel flat pass welding
production, each support spacing is 2 meters.
5. Lighting system: Light pass support cold plate bending and become,
specifications for 50×25ק1.0 mm, 40 x 40 x§1.5 mm carbon steel
flat pass welding production , each 2 m one paragraph, in turn,arrangement
, lighting using 40 w single belt cover fluorescent lamp , lined up on all fronts,
the whole line about 16 sets of tubes.
6. Socket slot: Use 2000 x 50×25 galvanized wire slot, is located under the machine belt,
points on both sides installation three, two square socket (every 1 m/workstation
install one).
7. Line body gas
path: All line body gas circuit using four points galvanized control, and in each station
with a set of 4 points quick connector;
8. Wind batch chute: Each side fixtures are one propose to batch chute, adopt FD28 30 x28 aluminum ,
each station a rings.
9. Process card
frame: In the fixtures are intermediate set two way process guidance card frame, the H
type aluminum guide production, each station layout a piece of A4 transparent
looking board hard rubber sleeve.
10. Station blocker: Using QX - type I stop device, each block device with a foot valve switch control.
11. Top body flat
moving
machine: On-line body ends, lifting SMC lifting cylinder device, conveyor belt use§5mm skid
proof conveyor belt production, bilateral decorate, drive use Taiwan production
miniature constant speed motor, motor power for 90 w 1:25, realize tooling plate
cycle delivery, a total of four sets
A? Project: Led bulb assembly line machines
B? Dimension: Model type: 12000 l×400w(belt)×750h(mm)
C? Structure: Single way pvc belt conveyor, galvanized roller transfer, independent frequency control of motor speed.
D? Description: Stable performance, safety and reliability, simple operation.
E? Specification:
1. Motor : Adopt 750w motor, wps 60 type 1:6 0 of the speed reducer, the chinese famous brand sondao 1 hp's frequency multiplier, frequency conversion sleepless speed regulation, linear speed 2-6m/min can be adjusted.
2. Machine body
& frame : Frame made by 40 x 40 square tube, stand by the same 40 x 40 square pipe production and become, below the belt by four points galvanized drum retainer and transfer; leg match galvanized adjustable foot cup; head plate with 1.2 mm cold plate bending rolling forming, body 2 meters one pieces.
3. Conveying belt: Using the netherlands imported high quality green light delivery special pvc belt, thickness of 2 mm, width of 400 mm, belt total length is 24000 mm, ring seamless pyro-condensation connection.
4. Independent
Working station : Independent table, specifications for 800long×600wide×750mm high(surface treated with antistatics), bilateral arrangement, the 25x 25 rectangular steel tube welding and become, 30l angle retainer; bedplate using 15mm quality compression plate, fastening fuselage both sides arrangement. Surface stick green antistatic soft rubber, green t strip edge; fastening fuselage both sides arrangement.Total of 16pcs of working table .
Dimension : 12000L×1900W×730H(mm)
Quality : One set
Structure : Hand push no power roller production line
Function and feature : This device is suitable for all kinds of LED street lights, tunnel lights electronic appliances, gas stove,
range hood, bathroom and other manufacturers, dedicated to gas appliances,
range hood, bathroom and other water assembly, stable, secure, reliable,
easy to operate.
Specification :
1. Body and frame : Frame and Tripod,Rod adopt 40X40 square tube made,Conveyor rollers using
L = 750mmF38 galvanized drum wall thickness 1.0mm. Branch arranged at
intervals of 100mm. Rack galvanized legs with adjustable foot cups.,and the
machine body is two meters per section.
2. Hand tooling plate: Specifications for the 800×60×15mm, 15mm high-quality plywood made of
high quality, high-quality anti-static soft surface leather paste, green T-tape sides
edging; across the board with 30 total tooling plate
3. Stands lighting : H-lamp mounted in the rack, use 40×20 square tube production, the connection
body of a lighthouse with 2000 ×50×25 spray duct connecting the power,per 2
meter, lighting choice of 40W single fluorescent tube bracket with cover ,
approximately every 1.3 meters to install a light tube, along the lines of bilateral
arrangement
4. Middle Stands: In light shelves located along Stands, for supporting the use of angle, width 300mm,
15mm compression using plate, face stickers bright green fire board.
5. Process card: On both side of line arrange the process card,using the H-type aluminum rail production,
every section with a A4 plastic paper.
6. Trachea : At the top of the lighthouse located along each side of the trachea; (of two), using 4
galvanized pipe, every meter an opening. (Quick Connector customer self-)
8. Ball table : Excessive tables at both ends using universal 1.2mm cold plate bending shape,
specifications for 1900 X850×730 (mm); surface evenly install universal bovine.
9. Working power: Using 2000 × 50 × 25 galvanized trough, located in the fuselage on both sides of
the drum, (of two) on each side of the way, the installation thirty-two socket (per meter / station to install a) bilateral use.
Dimensions 2080l×680w×1400h(mm)
Quantity One set/sets
Equipment structure In multistorey structure
Functional features This equipment dedicated to aging test bulbs, observation whether energy-saving lamps
For short circuit, blasting capacitance, black, etc. Simple operation, simple and convenient
The basic configuration and structure:
1. Machine body The frame adopts 40 * 40 aluminum profiles produced, is divided into 4 layers, each
Layer height is about 280mm.
2. Frame table Using 15mm compression plate cushion, the surface with white fire board, and
Installation e27 aging lamp holders , each layer can be also placed 120 led bulb
Lamp.Total of 480 pieces of led lamp holder .
3. Output The aging rack disposable and aging of the 480 led bulb lamp
4. Casters Installation of 4 pieces 2 inch wheels, two vientiane vientiane, two with brake, the convenience of customers to move .
5. Color The whole set of equipment for the the color of the aluminum.
6. Switch impact The time relay, open, close the impact time according to customer requirements.
A? Project : Led bulb b22 semi-automatic cap crimping machine
B? Dimension : 800×700×750(mm)
C? Quantity: 1 set
D? Function and feature : The special equipment for the e27 b22 base crimp and counter .At the same time to improve the product quality and yield, save a lot of artificial, safety, convenience and easy to operation.
E? Specification:
1. Air pressure:: About 0.6pa
2. Output : According to the degree of familiarity with employees, per minute maximum about 60
3. Model : E27 b22
4. The injection quantity : 12 injection
5. Frame : Fuselage framework using 40 x40 square tube welded together, feet wearing uses 40 x40 square tube welded together, channel steel, surface cover plate made from 1.5 cold plate bending.
6. Color : Vibration plate for primary colors, the rest of the white paint for computer processing, mechanical parts for black finish.
7. Warranty : ?lifelong telephone technical support services, mobile 24 hours ?
?warranty for one year
?sensors, needle cylinder, power indication warranty for half a year .
8. Accessories: Lamp holder needle 12pcs
A? Project Led down light aging line machine
B? Dimensions 12000l×1700w×750h(mm)
C? Quality One set
D? Structure Ring chain conveying, small car type independent testing aging, frequency control of motor speed
E? Function The led ceiling lamp and down light aging line to the detection of sophisticated light led products, led lights through the high-pressure, atmospheric pressure, low pressure, shock experienced roaming voltage area. Voltage adjustment range. Use whole lamp which features sophisticated and intuitive, easy to operate, suitable for different varieties of led lights. Power system frequency control system, easy to operate.
F? Specifications
1. Motor Speed motor : china brand 750w , reducer :chines famous brand ou fei er , wps80 , 1:60 type specific speed :1:6 frequency converter : sino-foreign joint venture's brand shendao 1 hp frequency converter, frequency conversion stepless speed regulation, the linear velocity of 0.3-2 m/min adjustable.
2. Structure The frame is 40×40 rectangular steel welding production;fuselage aging line using a dedicated special aluminum alloy;nose and tail curved seal plate is made of 1.5mm cold roll forming, galvanized legs with adjustable foot cups, body 2 m period.
3. Conveyor chain Shanghai chain factory produced using eight points double pitch chain holes.
4. Aging trolleys Whole aging line about 47 small circular trolley combination, easy aging different products:trolley outside dimensions: length 550 × width 440 × height 430 (mm).
5. Light blocking shield Located on both sides of the line all the way to block all decent light shield (except non-electric operating area), using 4mm combined with tinted plexiglas plate made of aluminum alloy. Effective energy-saving lamps light attenuation and better protect the eyes.
A? Project: LED tube light (fluorescent lamp) and bulb aging line totally machine
B? Specifications : 12000L×1540W×800H(mm)
C? Quantity : One set
D? Structure : Ring chain conveying, chain boards holder aging, frequency control of motor speed
E? Function and feature : This equipment is professional for LEDT8 tube light/led bulbs inspection. Through high voltage, normal voltage, low voltage, roaming and fluctuation voltage, impact functions. High temperature zones to observe whether short-circuit, capacitance burst and black points will occur. Also used for inspecting the simulation daily use of LED lamp cycling circuit and roaming seasoning area. Easy to cooperate.
F? S pecifications:
1. Motor : adopt 1500w motor, WPS80 type 1:60 of the speed reducer, the domestic well-known brand 2 HP's island converter, frequency conversion step less speed regulation, linear speed0.3—2M/min can be adjusted.
2. Machine body and strand : Made of 40×40 rectangle steel pipe by welding. Upper and lower body side protection using special aluminum alloy aging line dedicated. Protective board is made of 1.2mm cold steel sheet by bending. Support legs are equipped with galvanized adjustable soles.
3. Conveying chain: Double-pitch single-side-ear double-hole chain manufactured by Shanghai Chain Factory, 1.5m long.
4. Chain plate: Made of 2mm thick 1350×148×15mm cold rolling sheet, total 140 plates. 70 pieces of plants install 4 sets of plug for LEDT8 tube light ,Other 70 plates for 16pcs of E27 bulbs . And equipped with high marks broken small circuit breaker. Road conductive bottom of the chain plate mounting system(copper), each installation of two conductive blocks, each plate were installed 2.
5. Daily output: The aging line once can also aging 280pcs T8 tube lamp .1120pcs LED bulbs. The aging time for one hour. One day can work 10 hours. Total daily output is 2800pcs LED tube lamp and 11200pcs of LED bulbs one day.
6. Stop light shield: On both sides edges of the seven sections equipped a stop light shield plastic plates, using 4mm tawny organic glass plate and 40X40 aluminum alloy combinations and become effective damping light intensity to your eyes, better protect your eyes.
7. Conductive slot: Up and down with all conduction channel rail, the insulating rubber sheet, and assembly stainless steel electric tank.
8. Constant temperature area: Complete thermostatic system USES electric heating type, set for a period of two pieces of 2000 w/set of electro thermal heating plate, automatic constant temperature at room temperature - 60 ?, digital temperature control instructions.
A? Project LED tube light, ceiling lamp, bulb aging line multifunction machine
B? Dimensions 12000L×1700W×750H(mm)
C? Quality One set
D? structure Ring chain conveying, small car type independent testing aging, frequency control of motor speed
E? function The LED bulb and fluorescent lamp (tube light) aging line multifunction machine to the detection of sophisticated light LED products, LED lights through the high-pressure, atmospheric pressure, low pressure, shock experienced roaming voltage area. Voltage adjustment range. Use whole lamp which features sophisticated and intuitive, easy to operate, suitable for different varieties of LED lights. Power system frequency control system, easy to operate.
F? Specifications
1. Motor Speed motor : china Brand Bihebi, 750W Reducer :Chines famous Brand OU fei er ,WPS80 ,1:60 type specific speed :1:6 Frequency converter : Sino-foreign joint venture's Brand ShenDao 1 HP frequency converter, frequency conversion stepless speed regulation, the linear velocity of 0.3-2 m/min adjustable.
2. Structure The frame is 40×40 rectangular steel welding production;fuselage aging line using a dedicated special aluminum alloy;nose and tail curved seal plate is made of 1.5mm cold roll forming,galvanized legs with adjustable foot cups, body 2 m period.
3. Conveyor chain Shanghai Chain Factory produced using eight points double pitch chain holes.
4. Aging trolleys Whole aging line about 47 small circular trolley combination, of the upper and lower structural design, easy aging different products:
Trolley outside dimensions: length 550 × width 440 × height 1400 (mm); using doublelayer structure, the upper panel with 3% epoxy insulation board, install 24 E27 lamp holder, easy to aging LED bulb. 3% lower panel with epoxy insulation board blanket, install eight sets of four speakers clip, aging with outside lighting, installation of 14 sets of side-line bayonet T8 lamps, LED fluorescent tube aging. Each small trolley 24 sets of simultaneous aging bulb, 16 sets of external wiring LED lights, 14 sets of LED tube light.
5. Light blocking shield Located on both sides of the line all the way to block all decent light shield (except non-electric operating area), using 4mm combined with tinted plexiglass plate made of aluminum alloy. Effective energy-saving lamps light attenuation and better protect the eyes.
6. Conductive Systems: In the aging body frame along each side of the car is equipped with two(zero, Fire Wire)conductive grooves along the bilateral arrangement.
A? Project: Led bulb assembly line machines
B? Dimension: Model type: 12000 l×400w(belt)×750h(mm)
C? Structure: Single way pvc belt conveyor, galvanized roller transfer, independent frequency control of motor speed.
D? Description: Stable performance, safety and reliability, simple operation.
E? Specification:
1. Motor : Adopt 750w motor, wps 60 type 1:6 0 of the speed reducer, the chinese famous brand sondao 1 hp's frequency multiplier, frequency conversion sleepless speed regulation, linear speed 2-6m/min can be adjusted.
2. Machine body
& frame : Frame made by 40 x 40 square tube, stand by the same 40 x 40 square pipe production and become, below the belt by four points galvanized drum retainer and transfer; leg match galvanized adjustable foot cup; head plate with 1.2 mm cold plate bending rolling forming, body 2 meters one pieces.
3. Conveying belt: Using the netherlands imported high quality green light delivery special pvc belt, thickness of 2 mm, width of 400 mm, belt total length is 24000 mm, ring seamless pyro-condensation connection.
4. Independent
Working station : Independent table, specifications for 800long×600wide×750mm high(surface treated with antistatics), bilateral arrangement, the 25x 25 rectangular steel tube welding and become, 30l angle retainer; bedplate using 15mm quality compression plate, fastening fuselage both sides arrangement. Surface stick green antistatic soft rubber, green t strip edge; fastening fuselage both sides arrangement.Total of 16pcs of working table .
Project: Assembly station
Dimension : 12000l×1200w×780h(mm)
Quality : One set
Structure : Flat push delivery
Function : This devices is suitable for all types of lighting , and other manufactures, dedicated to
The assembly and packaging , safe, reliable , easy to operate
Specification:
1. Body : Racks are made of 40×40 rectangle made of welded steel pipe;galvanized legs with
Adjustable foot cups, body 2 m section.
2. Work table : With 15mm high-quality compression plate, anti-static rubber face stickers , width
1200mm, total length of 12 meters
3. Work power: Using 2000×50×25 galvanized trough, located in the fuselage on both sides of the
Installation of three, two side outlets(on average one every meter installation)
4. Lighting : H-lamp mounted in the rack , use 40×20 square tube production, the connection of
A frame body with every 2m and 2000×50×25 spray duct connecting the power,
Lighting choice of 36w fluorescent tubes with cover single bracket, each 1.5 meters
Installed a light tube, bilateral arrangement along the line .The lighting will be provided by buyer .
5. Electric control: Across the board is controlled by an electrical distribution box is completed, which
Is about two working power of control
6. Card: Lighthouse located in the middle of the process all the way to guide the card holder,
The use of h-type aluminum rail production, each station bill boards arranged a
Transparent hard plastic a4 sets.
7. Second layers : Specifications for the 12000×300×15mm, 30l angle iron supporting;platen using
High-quality 15mm compression plate, face stickers bright green fire board, located in
The middle of the light house from the conveying surface 300.
8. Color : Computer write
9. Notes: The device does not include a machine outside power lines, electrical control , intake and
Other peripheral devices.
A? Project: LED bulb and fluorescent lamp (tube light) aging line multifunction machine
B? Specifications : 12000L×1540W×800H(mm)
C? Quantity : One set
D? Structure : Ring chain conveying, chain boards holder aging, frequency control of motor speed
E? Function and feature : This equipment is professional for LEDT8 tube light/led bulbs inspection. Through high voltage, normal voltage, low voltage, roaming and fluctuation voltage, impact functions. High temperature zones to observe whether short-circuit, capacitance burst and black points will occur. Also used for inspecting the simulation daily use of LED lamp cycling circuit and roaming seasoning area. Easy to cooperate.
F? S pecifications:
1. Motor : adopt 1500w motor, WPS80 type 1:60 of the speed reducer, the domestic well-known brand 2 HP's island converter, frequency conversion step less speed regulation, linear speed0.3—2M/min can be adjusted.
2. Machine body and strand : Made of 40×40 rectangle steel pipe by welding. Upper and lower body side protection using special aluminum alloy aging line dedicated. Protective board is made of 1.2mm cold steel sheet by bending. Support legs are equipped with galvanized adjustable soles.
3. Conveying chain: Double-pitch single-side-ear double-hole chain manufactured by Shanghai Chain Factory, 1.5m long.
4. Chain plate: Made of 2mm thick 1350×148×15mm cold rolling sheet, total 140 plates. 70 pieces of plants install 4 sets of plug for LEDT8 tube light ,Other 70 plates for 16pcs of E27 bulbs . And equipped with high marks broken small circuit breaker. Road conductive bottom of the chain plate mounting system(copper), each installation of two conductive blocks, each plate were installed 2.
5. Daily output: The aging line once can also aging 280pcs T8 tube lamp .1120pcs LED bulbs. The aging time for one hour. One day can work 10 hours. Total daily output is 2800pcs LED tube lamp and 11200pcs of LED bulbs one day.
6. Stop light shield: On both sides edges of the seven sections equipped a stop light shield plastic plates, using 4mm tawny organic glass plate and 40X40 aluminum alloy combinations and become effective damping light intensity to your eyes, better protect your eyes.
7. Conductive slot: Up and down with all conduction channel rail, the insulating rubber sheet, and assembly stainless steel electric tank.
A? Project LED street lights, tunnel lights aging line machine
B? Dimensions 12000L×1700W×750H(mm)
C? Quality One set
D? structure Ring chain conveying, small car type independent testing aging, frequency control of motor speed
E? function The LED Street light and tunnel light aging line dedicated to the detection of sophisticated light LED products, LED lights through the high-pressure, atmospheric pressure, low pressure, shock experienced roaming voltage area. Voltage adjustment range. Use whole lamp which features sophisticated and intuitive, easy to operate, suitable for different varieties of LED lights. Power system frequency control system, easy to operate.
F? Specifications
1. Motor Speed motor : china Brand Bihebi, 750W Reducer :Chines famous Brand OU fei er ,WPS80 ,1:60 type specific speed :1:6 Frequency converter : Sino-foreign joint venture's Brand ShenDao 1 HP frequency converter, frequency conversion stepless speed regulation, the linear velocity of 0.3-2 m/min adjustable.
2. Structure The frame is 40×40 rectangular steel welding production;fuselage aging line using a dedicated special aluminum alloy;nose and tail curved seal plate is made of 1.5mm cold roll forming,galvanized legs with adjustable foot cups, body 2 m period.
3. Conveyor chain Shanghai Chain Factory produced using eight points double pitch chain holes.
4. Aging trolleys Whole aging line about 46 small circular trolley combination, of the upper and lower structural design, easy aging different products:Trolley outside dimensions: length 550 × width 440 × height 430 (mm); using double-layer structure.
5. Light blocking shield Located on both sides of the line all the way to block all decent light shield (except non-electric operating area), using 4mm combined with tinted plexiglass plate made of aluminum alloy. Effective energy-saving lamps light attenuation and better protect the eyes.
6. Conductive Systems: In the aging body frame along each side of the car is equipped with two(zero, Fire Wire)conductive grooves along the bilateral arrangement.
A? Project: anti pendant frame assembly line equipment
B? Dimension: Model type: 12000 L×600w(belt)×750H(mm)
C? Structure: Single way PVC belt conveyor, galvanized roller transfer, independent frequency control of motor speed.
D? Description: Stable performance, safety and reliability, simple operation.
E? Specification:
1. Motor : Adopt 750W motor, WPS 60 type 1:6 0 of the speed reducer, the Chinese famous brand SONDAO 1 HP's frequency multiplier, frequency conversion sleepless speed regulation, linear speed 2-6m/min can be adjusted.
2. Machine body
& frame : Frame made by 40 x 40 square tube, stand by the same 40 x 40 square pipe production and become, below the belt by four points galvanized drum retainer and transfer; Leg match galvanized adjustable foot cup; Head plate with 1.2 mm cold plate bending rolling forming, body 2 meters one pieces.
3. Conveying belt: Using the Netherlands imported high quality green light delivery special PVC belt, thickness of 2 mm, width of 400 mm, belt total length is 24000 mm, ring seamless pyro-condensation connection.
4. Independent
working station : Independent table, specifications for 800long×600wide×750mm high(surface treated with antistatics),bilateral arrangement, the 25x 25 rectangular steel tube welding and become, 30L Angle retainer; Bedplate using 15mm quality compression plate, fastening fuselage both sides arrangement. Surface stick green antistatic soft rubber, green T strip edge; Fastening fuselage both sides arrangement.total of 16pcs of working table .
5. Power
supply arrangement: 1.0 galvanized sheet bending and become, 2000x50x25 galvanized wire slot, is located under the fuselage belt, on both sides installation three, two square socket (every 1 m/workstation install one, bilateral installation).
6. Lamp lighting: choose 40 x 20 square tube welding production, connection on the machine body every 2m a frame with cold plate bending a 2000 x 50 25 connection power, makes workers operating space more open, lighting choose LED T8 lamp, bilateral along the line arrangement.
7. Electric devices
Control: Full range of electrical control done by a distribution box, with power left and right road control.
8. Operation card: Located in the middle frame processing instruction card stand all the way, uses the H - type aluminum rails manufacture, card board with A4 transparent hard plastic.
9. The upper table: 12000×400×13mm,by 30L angle steel bearing ,made of 13mm high quality plywood ,surface with anti-fire materials, space between the belt is 400mm.
Project Led panel lights aging shelf
Dimensions 2080l×1280w×1400h(mm)
Quantity 1 set/sets
Equipment structure In multistorey structure
Functional features This equipment dedicated to aging test bulbs, observation whether energy saving
Lamps for short circuit, blasting capacitance, black, etc. Simple operation, simple
And convenient
The basic configuration and structure
1. Machine body The frame adopts 40 * 40 aluminum profiles produced, is divided into 3 layers, each layer height is about 630mm.
2. Frame table We will installed 24 audio clip at the side of aluminum, each layer can be also placed 24 piece of led panel lights.
3. Output This aging shelf can aging 72 led led panel lights once at most.
4. Casters Installation of 4 pieces 2 inch wheels, two vientiane vientiane, two with brake,
The convenience of customers to move .
5. Color The whole set of equipment for the color of the aluminum.
6. Switch impact The time relay, open, close the impact time according to customer requirements.
A? Project : Led b22 bulb holder automatic cap crimping and riveting machine
B? Dimension : 800×700×750(mm)
C? Quantity: 1 set
D? Function and feature : The special equipment for the b22 base crimp and counter .At the same time to improve the product quality and yield, save a lot of artificial, safety, convenience and easy to operation.
E? Specification:
1. Air pressure:: About 0.6pa
2. Output : According to the degree of familiarity with employees, per minute maximum about 60
3. Model : B22
4. The injection quantity : 12 injection
5. Frame : Fuselage framework using 60 x40 square tube welded together, feet wearing uses 40 x40 square tube welded together, motherboard adopts 120 mma3 production. Retainer using 5, channel steel, surface cover plate made from 1.5 cold plate bending.
6. Color : Vibration plate for primary colors, the rest of the white paint for computer processing, mechanical parts for black finish.
7. Warranty : ?lifelong telephone technical support services, mobile 24 hours ?
?warranty for one year
?sensors, needle cylinder, power indication warranty for half a year .
8. Accessories: Lamp holder needle 12pcs
