Electric steering system is equl with the power steering system equipped a solenoid valve.
It is the system which steers with solenoid valve by comparing resistance values of electric handle and rudder angle sensor
It consists of a cylinder and a pump, an solenoid valve and a electric handle.
The cylinder makes the rudder move and the pump supplies the oil to the cylinder. Handle is to swap the direction of hydraulic pressure
Cylinder is classified Single, Rotary, Twin, Two rudders by torque and appearance
Pump is classified Pulley type drived by engine and Power unit drived by electric motor
We offer 7 kinds of handles with various appearance and functions.
You can choose the combination fit to your vessel
Key features
Narrow handle diameter helps you operate with small energy and power steering system offers light operation
The number of rotation wheel is 2.8 like the hydraulic handle
Analogue type of a indicator for handle and a rudder angle indicator are applied.
Controlled by Joystick / Autopilot
USB port
Autopilot can be used together.
Application
Vessel above 350HP
A wide range of vessel from fishing boat to ferry
Power steering system consists of a cylinder, a pump and handle. The oil is pressured from hydraulic pump and a
handle(orbitrol) control a cylinder.
The cylinder helps rudder move and the required oil is supplied from the hydraulic pump.
Cylinder is classified Single, Rotary, Twin, Two rudders by torque and appearance
Pump is classified Pulley type drived by engine and Power unit drived by electric motor
We offer 7 kinds of handles with various appearance and functions.
Features
Narrow handle diameter helps you operate with small energy and power steering system offers light operation
On where you put the handle, the rudder is fixed
Structure that the rudder does not rotate even when the tide power the rudder
When engine stops, manual steering is capable (Handle becomes heavy)
You can choose the combination fit to your vessel
Application
Vessel above 350 HP
A wide range of vessel from fishing boat to ferry
1. Inner check valve: the check valve inside the valve body is to insure the hydraulic oil will not be returned.
2. Inner relief valve: the relief valve inside the valve body is able to adjust the hydraulic system working pressure.
3. Oil way: parallel circuit, with power beyond.
4. Control way: manual, air, air&electric, micro-switch, electric&hydraulic control.
5.Valve construction: monoblock construction, 1-8 levers are available to assembled as you requests.
6.Spool function: o, a, y , p etc.
7. Flow 40 l/min with pressure 160bar, 200bar, 315bar
8.Spool returning type with t (spring return) and w (ball locking)
9. Joining port: l (screw connection)
10 .Nominal diameter: g1/2; g3/8; m18*1.5
Our product is a high quality product made from imported oils and additives of best quality. It has a very good life and will give the best performance under the most critical conditions. It is available in 210 ltrs. Hdpe drum/ 26 ltrs. And 50 ltrs.
Multi-brand Hydraulic Oils ISO VG 15, 32, 46, 68 and 100. Available in Drums, pails, IBCc, Bulk.
Kate, the buyer of Terex company, was asked by the head office last month to purchase a batch of hydraulic pressure valves within 3 months. She vowed to the owner that it would be completed in 2 months. As usual, Kate sent the hydraulic pressure valve inquiry to more than 10 hydraulic valve manufacturers she was familiar with, including American hydraulic valve manufacturers and Chinese hydraulic valve manufacturers. She chose 3 factories to provide hydraulic pressure valve samples for testing. After the test, the technical department informed that only the hydraulic pressure valve samples provided by American manufacturer were qualified. The trouble is that the price of the qualified hydraulic pressure valve exceeds 40% of the company's budget price. She has no authority to decide to use the products of this American hydraulic valve manufacturer.
After discussion with the technical department, she learned that those unqualified hydraulic pressure valves are mainly due to the wear or fracture of the sealing ring after 15,000 times of impact during the durability test of the hydraulic pressure valve, resulting in the leakage of the hydraulic pressure valve. Only those hydraulic pressure valves that have not leaked for more than 40,000 times are qualified. She was very depressed that the quotation of the other 3 hydraulic pressure valves was within the budget, but the quality was unqualified. At this time, Kate realized why the company gave him 3 months to purchase. She hurriedly sent inquiry to new hydraulic valve manufacturers, and specially emphasized the need for hydraulic pressure valves with more than 40,000 durability tests. The trouble is that no hydraulic valve manufacturer gave her an offer. Kate realized the difficulty of procurement. She had wasted 3 weeks. Procurement was still in its infancy, and the technicians had been urging progress.
After learning about Kate's purchase status, the colleague recommended her to contact AAK HYDRAULIC VALVE to try. When we received the hydraulic pressure valve drawing from Kate, we first gave a quotation. She told us very frankly that the price of AAK was 20% higher than that of other China hydraulic valve manufacturers, but 15% cheaper than that of the United States. She needed us to reduce the price greatly. We suggested providing the hydraulic pressure valve samples for testing first, and then discuss the price after passing the test.
2 weeks later, Kate informed that the test was qualified and AAK hydraulic pressure valve durability test had reached more than 40,000 times. She was surprised why AAK passed the hydraulic pressure valve durability test, while the other hydraulic valve manufacturers in China failed. AAK hydraulic valve was also eliminated by customers 2 years ago because the durability test of hydraulic pressure valve failed to meet the standard.
Gerrard, a Spanish hydraulic customer who just repeated the order at the end of May, repeated another order for hydraulic pressure valve again today, with total 3 orders for a hydraulic pressure valve a year. Since Gerrard chose AAK hydraulic valve, his customers are very satisfied with the accuracy and stability of AAK hydraulic valve. The market sales volume has increased by nearly 30% year-on-year. Now he has a higher and higher position in the company.
I still remember that Gerrard urgently needed to purchase a batch of hydraulic pressure valves for cranes. However, due to the high requirements for inner hole accuracy, he visited more than 10 hydraulic valve manufacturers, and none of them could reach around 1�¼m error requirement. Gerrard was very anxious. Fortunately, some peers brought Gerrard into contact with AAK. Finally, AAK helped to solve the problem of inner hole accuracy of hydraulic pressure valve smoothly.
3 months before Gerrard got into touch us, AAK HYDRAULIC VALVE purchased a honing machine imported from the United States to deal with the production of special orders. After repeated exploration for more than a month, modified the fixture of the equipment ourselves, we created the most consistent SOP to ensure the 1 �¼M accuracy error of the inner hole for the hydraulic pressure valve. At present, less than 5% of the domestic hydraulic valve manufacturers are equipped with this equipment. Among these 5% of hydraulic valve manufacturers, maybe only one manufacturer, we AAK HYDRAULIC VALVE, can modify the equipment on our own.
When AAK HYDRAULIC VALVE promised Gerrard that we have 90% of confidence to ensure that the inner hole accuracy of the hydraulic pressure valve can be controlled at 1 �¼ M, he was uneasy. After all, he visited more than 10 hydraulic valve manufacturers, and none of them successfully controlled the inner hole accuracy of the hydraulic pressure valve to 1 �¼mã??Gerrard also was in doubt. We can understand him, because we haven't done the hydraulic pressure valve with inner hole accuracy error controlled at 1 �¼ M before.
After 15 days of sending the sample, Gerrard emailed us that the sample of AAK hydraulic pressure valve was approved at one time, and the surface finish of the hydraulic pressure valve was also praised by his clients. Subsequently, the first hydraulic pressure valve order from him was successfully completed.
AAK hydraulic pressure valve has two absolute advantages in controlling inner hole accuracy:
1. AAK HYDRAULIC VALVE has advanced equipment - honing machine, which is refitted by ourselves to ensure that the inner hole accuracy of the hydraulic pressure valve can be controlled at 1�¼m.
2. AAK HYDRAULIC VALVE has targeted operation process, can realize the personalized customization demand for the inner hole accuracy of hydraulic pressure valve, which can not be achieved by 95% of domestic hydraulic valve manufacturers.
Just yesterday, I received a repeat order from Andy for a hydraulic flow control valve, which is just 3 months away from the delivery time of the last batch of hydraulic valves. The American customer Andy, started to communicate with us in 2019. Maybe it was just not the right time, we still didn't partner with each other till the beginning of this year. Because of encountering a Waterloo at the previous hydraulic valve manufacturer, he turned the tables at AAK and regained his confidence.
At the end of last year, Andy purchased a batch of hydraulic flow control valves from a hydraulic valve manufacturer. Because 20% of the shipments leaked, he encountered customer claims. The old hydraulic valve manufacturer was unwilling to bear the claim or re-produce. The customer kept pushing for replacement hurriedly. The owner asked him to find a high-quality hydraulic valve manufacturer to reproduce the goods for the customer.
Andy had a big headache at that time. The replacement quantity is not big, the hydraulic valve manufacturers with exquisite quality were unwilling to produce the small quantity for him. The hydraulic valve manufacturers who were willing to produce this quantity, were not able to meet the customerâ??s requirement about the roughness of hydraulic flow control valve. He ran into a wall everywhere, which made Andy haggard.
When Andy contacted with AAK HYDRAULIC VALVE, we are willing to cooperate with her to solve this difficult problem. We tested the leaked hydraulic flow control valve sample. The reason for the leakage is the roughness of the mounting surface of the hydraulic flow control valve. According to the customer's service conditions, this roughness must be controlled at 1.0 �¼ M or less. Andy is very confused why 80% of the installation surface roughness of hydraulic flow control valve is up to standard, while 20% is out of this range. The root of this fluctuation is the master's operation method, resulting in human error. The surface roughness is the depth, density, texture of the traces left on the machined surface from the action between the tool and the part surface, which depends on the master's processing technique.
Andy is very clear that at present, most domestic hydraulic valve manufacturers generally control the roughness of the installation surface of hydraulic flow control valve at 0.8-1.0 �¼ m. The biggest problem is not stable enough. Andy also knows that only AAK controls the roughness value of hydraulic flow control valve within 0.8 �¼ M, which can completely avoid leakage outside the hydraulic flow control valve, because of rest assured, Andy decided to repeat the order with AAK HYDRAULIC VALVE.
Just yesterday, I received a repeat order from Andy for a hydraulic flow control valve, which is just 3 months away from the delivery time of the last batch of hydraulic valves. The American customer Andy, started to communicate with us in 2019. Maybe it was just not the right time, we still didn't partner with each other till the beginning of this year. Because of encountering a Waterloo at the previous hydraulic valve manufacturer, he turned the tables at AAK and regained his confidence.
At the end of last year, Andy purchased a batch of hydraulic flow control valves from a hydraulic valve manufacturer. Because 20% of the shipments leaked, he encountered customer claims. The old hydraulic valve manufacturer was unwilling to bear the claim or re-produce. The customer kept pushing for replacement hurriedly. The owner asked him to find a high-quality hydraulic valve manufacturer to reproduce the goods for the customer.
Andy had a big headache at that time. The replacement quantity is not big, the hydraulic valve manufacturers with exquisite quality were unwilling to produce the small quantity for him. The hydraulic valve manufacturers who were willing to produce this quantity, were not able to meet the customer's requirement about the roughness of the hydraulic flow control valve. He ran into a wall everywhere, which made Andy haggard.
When Andy contacted with AAK HYDRAULIC VALVE, we are willing to cooperate with her to solve this difficult problem. We tested the leaked hydraulic flow control valve sample. The reason for the leakage is the roughness of the mounting surface of the hydraulic flow control valve. According to the customer's service conditions, this roughness must be controlled at 1.0 M or less. Andy is very confused why 80% of the installation surface roughness of hydraulic flow control valve is up to standard, while 20% is out of this range. The root of this fluctuation is the master's operation method, resulting in human error. The surface roughness is the depth, density, texture of the traces left on the machined surface from the action between the tool and the part surface, which depends on the master's processing technique.
Andy is very clear that at present, most domestic hydraulic valve manufacturers generally control the roughness of the installation surface of hydraulic flow control valve at 0.8-1.0 m. The biggest problem is not stable enough. Andy also knows that only AAK controls the roughness value of hydraulic flow control valve within 0.8 M, which can completely avoid leakage outside the hydraulic flow control valve, because of rest assured, Andy decided to repeat the order with AAK HYDRAULIC VALVE.