Custom made turbine blade for steam turbine and gas turbine compressor. Non-OEM where quality and pricing offers a good deal.
Supplier: Urea n46, diesel en590 10ppm, jet fuel a1, dap, basalt fiber products, nitrocellulose centralite ii wind turbine gearbox accessories
Services: Import and export of goods and technology
Buyer: Urea 46, diesel oil en590 10ppm, jet fuel a1, dap 18 46 , crude benzene, pure benzene
Turbine blade Steam turbine blades for all oem model turbines. Gas turbine compressor blades, compressor vanes, inlet guide vanes (vigv, igv). Ge, general electric siemens, westinghouse, fiat, pratt & whitney, mitsubishi, alstom, mhi, fuji, toshiba, shin nippon, fiat, coppus, murray, franco tossi, terry, dresser rand, delaval, allen, peter brotherhood, english electric, abb, bbc, aeg kanis, sulzer, ansaldo, fincantieri, nuovo pignone, kkk, nadrowski. Various
This blender series have the characteristics of universal round plate turbine blender.The difference is the change of the leave's section shape,as to increase the pump transferring capability of the blender,improve the performance of dispersion and media.The operation condition is the same with the universal round plate turbine blender. Flow state:The flat blade impeller and curved blade impeller are radial flow.When there is baffle,the upper and down circulating flows can be formed from the blade boundary.The opposite pitched subsidiary blade impeller has an axial shunt.The capacity mixing of liquid above and below the disc is worse than the open turbine impeller.
The Axial turbine is for low head power plants. Water flows axially into and out of the turbine. Axial flow turbines fall into two categories, fixed blade runner and variable pitch runner, also known as a Kaplan turbine. Fixed blade turbines are very well suited to low head power plants with limited variation in head and load. Its main advantage is its simple design. When operated at fixed speed, maximum efficiency is achieved at the design head and water flow. Kaplan turbines are used for medium to large power stations where there are large variations in the head, water flow and load. Its main advantage is its ability to adapt to variable conditions with a high efficiency. The variable pitch runner is mechanically more complex than a fixed pitch runner. Axial flow turbines can be supplied for a head of 2m to 70 m. The runner diameter is available from 0.6 m to 5 m. Power capacity is from 55 kW to 50 MW.
The tubular turbine is an axial flow turbine, in a straight or S-shaped configuration. A Tubular Turbine can be supplied for a head of 2 m to 30 m. The runner diameter is available from 0.8 m to 5.6 m. Power capacity is from 250 kW to 15 MW. This turbine has high efficiency and lower constructon cost.
Pelton turbine The runner has bucket shaped blades on the periphery. The jet of water is tangential to the runner. The characteristics are, high head applications, a simple design, few problems with cavitation, highly cost effective. Pelton turbines can be supplied for a head of 100m to 500 m. The runner diameter is available from 0.55 m to 1.5 m. Power capacity is from 200 kW to 10 MW. Inclined jet turbine: The water flows into and out of the runner at an angle to the main shaft. The characteristics are high efficiency over a wide range of water flow, more flexible installation options, somewhat more complex than a Pelton turbine. Inclined jet turbines can be supplied for a head of 60m to 300 m. The runner diameter is available from 0.32 m to 0.8 m. Power capacity is from 55 kW to 6.3 MW.
In a Francis turbine, the water flows radially into the turbine and axially out of the runner. The Francis turbine, invented by an American engineer in 1849, is the most widely deployed modern turbine. The main characteristics of the Francis turbine are - a wide range of water head, simple and reliable structure, and high efficiency. A Francis Turbine can be supplied for a head of 15 m to 250 m. The runner diameter is available from 0.4 m to 4.5 m. Power capacity is from 75 kW to 50 MW. New style francis turbine, compared to the old one, it has the advantages of convenient installation, high efficiency, low noise and compact structure.
Rated Power : 30KW Shaft Power : 34.5KW Rated Wind Speed : 10m/s Cut-in Wind speed : 3m/s Cut-out Wind speed : 25m/s Max Cp : 0.48 Rotor Diameter : 12m Blade Length : 5.58m Tip Chord : 230mm Max Chord : 783mm Material : FRP Weight(Kg/pcs) : 112 Direction : Clockwise Orientation : Upwind Configuration : Horizontal Survival Speed : 52.5m/s Standard : AWEA/IEC Design Life : 20years Bolt Circle Dia : 248mm
