Ature:remove all oil or grease, soluble contaminants and other foreign matter All surfaces to be coated should be clean, dry and free from contamination If applied on rusty surface, rusty layer thickness should be below 50mm, other than bottom surface processing requirements, without acid and sandblasting processing, catalytic reaction, to get black protective layer and solvent (acrylic acid, polyurethane, epoxy resin, alkyd resin, amino paint or water-based paint) match well, will not occur and paint color bleeding Apply in nice weather, don't let coating contact any liquid like water or other solvent before completely dry No painting be carried out in rainy day outdoor If above 85% humidity please stop painting Temperature of substrate should be above 5¡ãc Lower temperature might not dry or cause long time to dry •air spray:nozzle orifice range: 1.5 to 2.5mm Nozzle pressure range: 0.3 to 0.5mpa •airless spray:nozzle orifice range: 0.4 to 0.5mm Nozzle pressure range: 12 to 15mpa •features:brush: use soft brush Recommended finish: rsl series Storage temperature: 5 to 30¡ãc in well ventilated warehouse Stir thoroughly before painting Don't use any steel or other metal stick to stir paint 20l/barrel
Can be applied directly on rusty steel( rust layer ¡ü45um)! Color and appearance: grey or others Coating thickness um: 50¡à5mm Solid content % : 69¡à3% Overcoating interval: minimum: 4 hours max: unlimited Recommended substrate conditions and temperature: 1.Remove all oil or grease, soluble contaminants and other foreign matter. All surfaces to be coated should be clean, dry and free from contamination. 2.If applied on the rusty surface, the rusty layer thickness should be below 45 um 3.Apply in good weather, don¡¯t let coating contact any liquid like water or other solvent before completely dry. No painting be carried out in rainy day outdoor , if the humidity is above 85%, please stop painting 4.The temperature of substrate should be above 5¡ãc, lower temperature might not dry or cause a long time to dry Air spray:nozzle orifice: 1.5-2.5mm Nozzle pressure: 0.3-0.5mpa Airless spray:nozzle orifice: 0.4-0.5mm Nozzle pressure: 12-15mpa Brush : use soft bursh Recommended finish: rsl series finish Shelf life: 12 months Over coating time Substrate Temperature 5¡ãc 15¡ãc 25¡ãc 35¡ãc 45¡ãc Minimum interval 24hrs 7hours 4hours 3hours 2hours Maximum interval Unlimited storage temperature : 5-30¡ãc in well ventilated warehouse 20l/barrel or 20kg/barrel
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
PC natural 100% pure pc without any coating MATERIAL: PC natural 100% pure pc without any coating CATEGORY: PC TYPE: Natural SPECIFICATION: Separate 25 kg bag and Mark per month 78 mt 100% pure pc without any coating ,post Industrial materials Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1450$ - 1700$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days Our Commitment We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation. 2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
BARILAC barrier coatings are the most suited sustainable solution to replace polycoated laminated board, waxcoated, PVDC coated etc all non sustainable alternatives. Barilac barrier coat is recommended for paper cup, trays, foodtrays, pizza boxes, ice cream cartons etc. The special product features are. - Low COBB - Good oil and grease resistance - Good Moisture Vapour Transmission rate - Good heat sealing performance - Good water resistance - Low odour - FDA compliance
Water Based Coatings - Primers, Gloss & High Scuff - High Gloss/High Slip - Duct Gloss & Matt - Specialty Coatings - Soft Feel / Satin / Neutral / Super Matt
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
PU Paints
