Stearic acid is a commonly used ingredient in candle making and plays a crucial role in the formulation of candles. Here's an overview of stearic acid's role and its benefits in candle production: 1. Wax Hardening: It is used to harden the wax and increase its melting point. This helps candles maintain their shape and structure, especially in warmer environments. 2. Enhances Burning Properties: It improves the burn quality of candles by slowing down the rate of combustion. This results in longer burn times and helps reduce dripping and excessive smoking. 3. Opacity and Color Enhancement: It can enhance the opacity of candle wax, especially when using translucent or colored waxes. It helps achieve a more vibrant and solid color appearance. 4. Mold Release Agent: It acts as a mold release agent, making it easier to remove the finished candles from their molds without sticking or damaging the shape. 5. Fragrance Retention: It can help improve the retention and diffusion of fragrance oils in candles. It allows the fragrance to bind more effectively with the wax, enhancing the scent throw during burning. 6. Stability and Shelf Life: The addition of stearic acid to candle wax can increase its stability and shelf life. It helps prevent the wax from discoloration, deterioration, or developing a stale odor over time. 7. Texture and Consistency: It can contribute to the smoothness and creaminess of the candle wax, improving its texture and consistency during the pouring and solidification process. When using stearic acid in candle making, it is important to consider the appropriate dosage. Excessive amounts of stearic acid can lead to issues like excessive smoke, decreased scent throw, or poor burning performance. It is recommended to follow specific guidelines and conduct small test batches to determine the optimal amount of stearic acid based on the desired results. Overall, stearic acid is a valuable ingredient in candle making, offering benefits such as wax hardening, improved burn quality, color enhancement, fragrance retention, and overall stability. FAQs: How much stearic acid is good for making candles with paraffinï¼? The proportion of stearic acid added can vary according to specific needs. If the purpose is to increase the hardness of the candle and reduce issues such as bubbles and cracking, an intermediate value, such as 5% to 10%, can be chosen. If it is for specific process effects, a higher proportion or even the maximum amount of addition may be required. However, to avoid excessive emulsification and other potential issues, it is not recommended to add more than 30%.
Dear Sir/ Mrs We're happy to hear you're shopping for your favorite Rice Noodle, vermicelli and pho We send you catalogs and offers with the following components: Ingredients are made from rice, galangal tubers, potatoes, to create flexibility and help better preservation, Toan Thang food is a new product line that Toan Thang food helps to diversify delicious meals for each family to choose. how you cook your favorite food. Ingredients: 100% natural ingredients without preservatives. User manual: Soak vermicelli, pho, and vermicelli in cold water for about 5 minutes. - Take out and wash with clean water to dry, optionally use. - Stir-fry shrimp, crab, meat, eggs, vegetables, spices... depending on your preference... - Serve with hot pot or use fresh noodles.... Cooking instructions Fresh vermicelli Bring water to a boil in a saucepan until it is completely boiled (100 degrees Celsius or 212 degrees F .). - Put pho noodles in boiling water (100M degrees C) and cook for 8 minutes. - Pour the vermicelli into the basket and rinse with cool water, drain for 5 minutes. - Rice vermicelli can now be served with broth. - Pho roll: Bring water to a boil in a pot until it is completely boiled (100 degrees C or 212 degrees F). - Put pho noodles in boiling water (100 degrees Celsius) and cook for 5 minutes. - Pour the vermicelli into the basket and rinse with cool water, drain off the water. - Prepare a hot pan, put a little oil, put meat, vegetables, mushrooms, seafood in. - Stir-fry for a few minutes. - After the mixture is cooked, put the vermicelli into the pan, mix everything and stir-fry until the vermicelli is evenly absorbed, season with spices and use immediately. We hope to bring delicious food to your family, if you have any questions, please email us as soon as possible so that we can serve you the best.
Avaruni Skin Whitening Cream Our Skin Whitening Cream is made with the perfect combination of Shea Butter & Essential Oils. Avaruni Skin Whitening Cream gives you the gift of a lighter and even skin tone within 15-20 days. Other benefits of the skin include: 1. Natural Glow 2. Hydrated Skin 3. For both, men and women 4. Suitable for all skin types 5. 100% guaranteed & reliable results 6. Time-tested formula 7. No side effects With our Skin Whitening Cream, we truly deliver the remarkable results that we promise. You�¢??re not just getting the product �¢?? but the results are well within your reach in a few weeks. We recommend this cream to anyone above 19 years of age. Why choose the Avaruni Skin Whitening Cream? 1. Get 2-6 shades lighter depending on your current skin tone 2. Get a natural glow that mirrors the look of celebs 3. Effectively remove all traces of sunburn and tan from your skin 4. Reduce and completely eliminate dark circles 5. Naturally heal your pimples and marks 6. Reduce skin pigmentation, scars, and acne 7. Reduce black patches on the neck, elbow pits, armpits, knees, and ankles 8. Apply on any part of your body for direct results
TOPTITECH's 30" SUS 316L Sintered Alloy Porous Filter Elements are crafted from premium SUS 316L stainless steel alloy, ensuring durability and reliability in demanding environments. The sintered alloy construction provides excellent resistance to heat, corrosion, and physical wear, making them ideal for challenging filtration applications. The linked pores in the porous structure of the 30" SUS 316L Sintered Alloy Porous Filter Elements facilitate the effective removal of pollutants. The large surface area facilitates optimal particle capture, ensuring high filtration efficiency while minimizing pressure drop. With customizable configurations available, TOPTITECH can tailor the pore size, thickness, and shape to meet specific filtration needs. Parameter Material: SUS 316L Length: 30â?? Diameter: 30mm Pore size: 15 um Wall thickness: 2.5mm Connector: 1/2â?? NPT Features Exceptional Durability High Filtration Efficiency Robust Heat and Corrosion Resistance Customizable Configurations Wide Range of Applications What is 1/2â?? NPT connector? The 1/2â?? NPT interface refers to a common standard for pipe threads used in connecting fittings and components. NPT stands for National Pipe Taper, which is a widely adopted thread standard in the United States. In this product, 1/2â?? NPT indicates that the thread size of the interface is 1/2 inch. NPT interfaces feature a tapered thread design, where the threads gradually narrow toward the end of the pipe, creating a cone shape. This design ensures a secure connection that helps prevent oil or gas leakage effectively. The 1/2â?? NPT interface finds extensive applications in various industries, including fluid and gas transfer systems, pipe connections, valves, instruments, and other equipment involving pipe connections. It is widely embraced in industrial settings due to its ease of installation, high reliability, and ability to withstand high-pressure and temperature environments. It is important to note that NPT interfaces are tapered thread standards and are not compatible with parallel threads (such as NPS). Therefore, when selecting and connecting fittings, it is crucial to ensure the use of the same type of thread to achieve tight and reliable connections.
The compact Dtorque 111 is designed to revolutionize the small workboat market where its expected lifespan of well over 10,000 hours at least doubles that of any comparable outboard gasoline engine. The Dtorque 111 offers a remarkably smooth and quiet diesel engine, delivering 50 hp at the propeller with a stunning torque output of 111 Nm at just 2,500 rpm. This is considerably better than the latest 70 hp 4-stroke gasoline models and more than enough to quickly accelerate most small craft onto the plane with plenty of low-down lugging power for heavy displacement duty. The Dtorque is the ideal choice if you operate or manage: work boats safety/rescue boats fishing boats governmental and port authority vessels passenger boats superyacht tenders Increased Safety Diesel is less flammable than gasoline, and so the Dtorque is the safer choice for potentially hazardous environments, such as in the oil and gas industry. Superyacht and cruise ship operators, for example, will also benefit from the time and cost savings associated with having fewer fire safety precautions and regulations. In addition, there is only one type of fuel to manage, which is more widely available in ports all over the world. The Dtorque also exceeds EU RDC Stage II emissions regulations, however, is not yet EPA compliant. Low Noise and Vibration The Dtorque has a two-cylinder, common rail, turbo-charged diesel engine that uses a unique system of dual counter-rotating crankshafts in an aluminum block. This technology, with its patented â??Spaceballâ?? design, helps reduce vibrations and noise. Another advantage of these crankshafts is the lack of rotating and operating (steering) torques. This results in less fatigue during the engines operation.
Changhao is a leading manufacturer of elbows, including 45 elbows, 90 elbows and 180 elbows. we ensure 100% best quality and tested products. The purpose of an elbow is to adjust the direction of flooding in a piping system. Elbows are classified into three major categories in terms of short and long radii - 45 degrees, 90 degrees and 180 degrees. We offer our valued customers a perfectly finished and durable range of butt-weld elbows, which are manufactured from the best standard quality stainless steel in different grades. The 90 elbow is used for installation between two sections of pipe or tubing, allowing for a 90 directional change. 180 elbow is used for installation between two sections of pipe or tube, allowing a 180-degree change in direction. Changhao offers elbows in different sizes, materials and grades. Our elbows are available in a wide range of materials such as steel elbows, carbon steel elbows, alloy steel elbows, etc. These special elbows can be customized for our customers based on thickness, size and other factors they require. We also deliver these products as per the sketches provided by the customers. Changhao manufactures elbows with long service life, while our products are the most economically priced. We have a large customer base in seamless pipe and fittings, which allows us to offer the best discounts to our customers. Our focus is clearly to increase the number of customers and help our customers purchase the best quality goods at the lowest prices. We offer a price guarantee on most of our products, meaning that we can match any price target if reasonably possible. We produce 45-degree elbow, 90-degree elbow, and 180-degree elbow according to ASTM B16.9/16.5/16.47A/16.47B B2220-2001, SH3408, SH3409, GBT12459, GB/T13401 standards. Our products are widely used in oil and gas, petrochemical, refinery, power plant, shipbuilding, metallurgy, paper making and other industries.
Description Two-component acrylic aromatic polyurethane finish coating Recommended Use :- This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries. It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry. Physical Data COLOUR : Assorted shades FINISH : Glossy / Semi glossy / Matt SOLIDS BY VOLUME : 40 ± 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 µ FLASH POINT : Base : Above 23 C Hardener : Above 23 C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 DAYS. SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional spray / By Airless Spray THINNER : Type 290 POT LIFE : 3 hours min at 30 C RECOMMENDED DFT : 30-40 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Description Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating. Recommended Use :- This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application. Physical Data COLOUR : Industrial Shades FINISH : Glossy / Semi-glossy SOLIDS BY VOLUME : 40 + 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr @ recommended DFT of 30 FLASH POINT : Base : Above 23 C Hardener : Above 23C DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base: Hardener - As per our recommendations APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Type 290 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30- 40 . OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Description Two Component, Air-drying, Epoxy Polyamide Cured Finish Paint. Recommended Use :- It Is Recommended As A Top Coat For Structures, Pipelines, Vessels, Equipments And Machineries, Storage Tanks Etc. In Fertilizers And Chemical Plant, Cement Plants, Power Plants, Steel Plants, Pharmaceutical And Petrochemical Complexes, Refineries Etc. Product Is Also Recommended For Application Over Suitable Primer For Oem Industry Like Machine Tools, Pumps, Machineries, Transformers Etc. Physical Data Colour : assorted Shades Finish : glossy / Semi Glossy Solids By Volume : 40 +3% (depends On Shade) Theoretical Spreading Rate : 13.33 Sq.mt / Ltr At Recommended Dft Of 30 au Flash Point : base: Above 23 C Hardener: Above 23 C Drying Characteristics (at 30'c And 65% Relative Humidity) : hard Dry : Overnight Full Cure : 7 Days Shelf Life : base : 6 Months Hardener : 6 Months Surface Preparation This Being A Topcoat, Which Is Applied Over, Primer Or Intermediate Coats, The Surface Should Be Free From Oil, Moisture, Dust And Dirt. Aged Epoxy / Pu Coating Should Be Roughened By Emery Paper Grade 400 / 600 For Better Bonding. Application Data :- Mixing Ratio : base : Hardener (as Per Our Recommendation) Application : by Brush / By Conventional Spray / By Airless Spray Thinner : 190 Pot Life : 4-6hrs Min At 30 C Recommended Dft : 30-40 U Over Coating Interval : min : 8 Hours Max : 24 Hours Compatibility : can Be Over Coated With Pu, Chlorinated Rubber And Synthetic Enamel Paints.
Description Two component, air-drying, Epoxy polyamide cured finish paint. Recommended Use :- It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc. Physical Data COLOUR : Assorted Shades FINISH : Semi glossy SOLIDS BY VOLUME : 40 �± 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr at recommended DFT of 30 �µ FLASH POINT : Base: Above 23�° C Hardener: Above 23�° C DRYING CHARACTERISTICS : SURFACE DRY : 90 minutes max HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : 190 POT LIFE : 4-6hrs min at 30 �° C RECOMMENDED DFT : 30-40 �µ OVER COATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with PU, Chlorinated rubber and synthetic enamel paints.
Description Two-component air-drying intermediate/primer surfacer coat. Recommended Use :- Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats. Physical Data :- COLOUR : Grey, White FINISH : Egg Shell to Matt SOLIDS BY VOLUME : 40 �± 3% SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ FLASH POINT : Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting. Application Data :- MIXING RATIO : Base: Hardener ( As per our recommendation) APPLICATION : By Brush/ By Conventional Spray / By Airless Spray THINNER : Type 290 POT LIFE : 4 hours min at 30�° C RECOMMENDED DFT : 30 -35 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
TECHNICAL SPECIFICATION 1. Capacity : 50KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65 C with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
Casting iron balls include high chromium balls, medium chromium balls and low chromium balls. Quality index of high chromium casting ball: The chromium content of the high chromium ball is 10.0% or more. The carbon content is between 1.80% and 3.20%. According to national standards, the hardness of the high chromium ball must be no less than 58hrc, and the impact value should be greater than or equal to 3.0j/cm2. To achieve this hardness, the high chromium ball must be quenched and tempered at high temperature. At present, there are two methods for quenching high chromium balls in China, including oil quenching and wind quenching. If the test hardness of the high chromium ball is lower than 54HRC, it means that it has not been quenched. Quality index of medium chromium casting ball The specified chromium content of the medium chromium ball ranges from 3.0% to 7.0%, and the carbon content is between 1.80% and 3.20%. Its impact value should not be less than 2.0j/cm2. According to national standards, the hardness of the chrome ball should be greater than or equal to 47hrc. In order to ensure quality, medium chromium balls should be tempered at high temperature to eliminate casting stress. If the surface of the iron ball is black and red, it proves that the iron ball has been tempered at high temperature. If the surface of the iron ball still has the metal color, we can judge that the iron ball has not undergone high temperature tempering treatment. Quality index of low chromium casting ball Generally speaking, the chromium content of the low chromium ball is 0.5% to 2.5%, and the carbon content is from 1.80% to 3.20%. Therefore, according to the national standard, the hardness of the low chromium ball should be no less than 45hrc, and the impact value should be no less than 1.5j/cm2. Low chromium balls also need high temperature tempering treatment to ensure quality. This treatment can eliminate casting stress. If the surface of the iron ball is dark red, it indicates that it has undergone high temperature tempering treatment. If the surface is still metallic color, it means that the iron ball has not been tempered at high temperature. Casting iron balls are usually used in various large-scale mines, cement plants, chemical plants, power plants, quartz sand plants, silica sand plants, etc.
Attar-Dipped Incense Sticks: Immerse yourself in the enchanting world of attar-infused fragrances. Our attar-dipped incense sticks are delicately crafted using the finest natural ingredients. Each stick is infused with the essence of pure attars, capturing the essence of nature's most captivating scents. Whether you seek the soothing notes of lavender or the invigorating aroma of citrus, our attar-dipped incense sticks promise to envelop you in a fragrant embrace that awakens the senses and uplifts the soul. Masala Powdered Incense Sticks: Experience the art of aromatherapy with our masala powdered incense sticks. Expertly blended with a harmonious combination of aromatic spices and herbs, these sticks release a rich and lasting fragrance that resonates with tradition. Our masala powdered incense sticks are a testament to the age-old practice of blending natural ingredients to create scents that evoke a sense of nostalgia and serenity. Ignite one of these sticks and let the aromatic symphony unfold, transforming your space into a sanctuary of tranquility. Insect Repellent Incense Sticks: Combine the power of aromatics with the functionality of insect repellents. Our insect repellent incense sticks are thoughtfully formulated to keep unwanted guests at bay, naturally. Crafted with a blend of aromatic oils and spices, these sticks emit fragrances that humans adore but insects detest. Create a pest-free haven in your home or garden while immersing yourself in scents that inspire calmness and serenity. Each of our attar-dipped, masala powdered, and insect repellent incense sticks is a testament to our commitment to quality, authenticity, and environmental consciousness. Let the symphony of fragrances from Maa Impax fill your life with moments of pure delight and bliss.
PET bottle blowing compressors are specialized machines used in the manufacturing process of PET (polyethylene terephthalate) bottles. These compressors are designed to provide the necessary compressed air for the bottle blowing process, which involves shaping and forming PET preforms into bottles. The bottle blowing process typically consists of the following steps: PET Preform Heating: The PET preforms, which are small plastic tubes with a threaded neck, are first heated in a preform oven to a temperature where they become soft and pliable for shaping. Preform Transfer: The heated preforms are then transferred to the blowing machine using a preform transfer system. This system usually includes a series of conveyors or robotic arms to move the preforms to the blowing station. Bottle Blowing: In the blowing station, the preforms are placed into molds called blow molds. Compressed air is then injected into the preforms, expanding them to the shape of the mold cavity. This process forms the bottles' final shape. Cooling and Ejection: Once the bottles have taken shape, they are cooled down using chilled air or water to solidify them. The bottles are then ejected from the molds and sent for further processing, such as labeling, filling, and packaging. PET bottle blowing compressors play a crucial role in the bottle blowing process by providing the high-pressure compressed air needed to inflate the preforms and create the desired bottle shape. These compressors are typically designed to deliver clean, dry, and oil-free compressed air to ensure the quality and integrity of the bottles. The compressors used for PET bottle blowing are typically reciprocating or rotary screw compressors. They are designed to handle the specific requirements of the blowing process, such as delivering high-pressure air quickly and efficiently. The size and capacity of the compressor depend on factors such as the production volume, bottle sizes, and the specific requirements of the bottle blowing machine.
1 Series Aluminum Disc/Circle Parameter: Deep drawing aluminum circle/disc 1050, 1060, 1100, 1200 etc. Aluminum Alloy Thickness(mm) Diameter(mm) Temper 1050, 1060, 1100 0.5-5.0 100-1500 HO, H12, H14, H22, H24 Material process CC AND DC (DC For cookware and CC for road sign) DC for cookware with good deep drawing and spinning Further Fabrication Deep Drawing, Spinning, Anodizing Customize size Size can be produced as per clients requirement Surface Mill finish, or color coated or anodized MOQ per size 3 tons Quality Standard ASTM B209, EN573-1 Price terms FOB, CRF, CIF Payment Terms 30% deposit in advance, 70% balance payment by TT or LC Surface Mill Finish, Plain Standard GB/T, ASTM, EN Delivery time Within 25 days after receipt of the lc or deposit Material Quality Totally free from defects like roll makers, edge damage, oil stain, white rust, dents, scratches, etc. A+++ quality Equipment 6 hot tandem rolling line, 5 cold mill production lines Application DC hot roll for cookware and utensils and CC for road signs Packing Standard export worthy wooden pallets, and standard packing is about 1 ton/pallet. Pallet weight also can be as per clientâ??s requirement, and one 20â?² can be loaded about 25mts. Loading Port Any port of China, Shanghai & Ningbo &Qingdao Delivery Methods 1. By sea: Any port in China 2. Other
1 Series Aluminum Disc/Circle Parameter: Deep drawing aluminum circle/disc 1050, 1060, 1100, 1200 etc. Aluminum Alloy Thickness(mm) Diameter(mm) Temper 1050, 1060, 1100 0.5-5.0 100-1500 HO, H12, H14, H22, H24 Material process CC AND DC (DC For cookware and CC for road sign) DC for cookware with good deep drawing and spinning Further Fabrication Deep Drawing, Spinning, Anodizing Customize size Size can be produced as per clients requirement Surface Mill finish, or color coated or anodized MOQ per size 3 tons Quality Standard ASTM B209, EN573-1 Price terms FOB, CRF, CIF Payment Terms 30% deposit in advance, 70% balance payment by TT or LC Surface Mill Finish, Plain Standard GB/T, ASTM, EN Delivery time Within 25 days after receipt of the lc or deposit Material Quality Totally free from defects like roll makers, edge damage, oil stain, white rust, dents, scratches, etc. A+++ quality Equipment 6 hot tandem rolling line, 5 cold mill production lines Application DC hot roll for cookware and utensils and CC for road signs Packing Standard export worthy wooden pallets, and standard packing is about 1 ton/pallet. Pallet weight also can be as per clientâ??s requirement, and one 20â?² can be loaded about 25mts. Loading Port Any port of China, Shanghai & Ningbo &Qingdao Delivery Methods 1. By sea: Any port in China 2. Other
The melting point of WJWAX's food grade paraffin wax NO.58 is about 58-60. This product is widely used in gum based production of chewing gum and Bubble gum in China. It is also a very popular food grade paraffin product abroad. We are a direct distributor of Kunlun and Sinopec, offering highly competitive prices. Paraffin wax is a white or colorless soft solid that's used in a variety of applications due to its chemical stability, large molecular weight, and low reactivity. It's a byproduct of the oil refining process, and its properties can be fine-tuned by controlling the refining process. Paraffin wax with a melting point of 58-60â?? is often used in the food industry, particularly in the production of gum base, the non-nutritive, non-digestible, water-insoluble base used to carry sweeteners, flavors, and colors in chewing gum and bubble gum. Product Application Melting Point: Paraffin wax No.58-60â?? has a melting point in the range of 58 to 60 degrees Celsius. This property makes it ideal for use in the gum base, as it will not melt easily in the mouth during chewing. Tasteless and Odorless: This type of paraffin wax is both tasteless and odorless. Therefore, it does not interfere with the flavors added to the chewing gum. Safe for Consumption: Food-grade paraffin wax is deemed safe for consumption, ensuring it doesn't pose any health risks when used in gum bases. Viscosity: Paraffin wax has a low viscosity which contributes to the smooth texture of the chewing gum. Insoluble in Water: The wax is insoluble in water, which helps to keep the gum from dissolving while it's being chewed. Uses in Gum Base In a gum base, food-grade paraffin wax serves several purposes: Texture and Chewability: The wax helps to provide the gum with its characteristic elasticity and chewiness. Stability: It aids in maintaining the stability of the gum, preventing it from breaking down or dissolving during chewing. Flavor Retention: Paraffin wax helps to encapsulate and retain the flavoring agents in the gum, releasing them over time as the gum is chewed. Shelf Life: It also contributes to the long shelf life of gum products by serving as a moisture barrier. Paraffin wax No.58-60â?? is just one of several ingredients in a typical gum base. Others may include elastomers, resins, plasticizers, antioxidants, and fillers. All these ingredients are carefully chosen and combined to achieve the desired characteristics of the final gum product. Conclusion Food-grade paraffin wax No.58-60â?? is a crucial ingredient in the production of gum base. Its unique properties contribute to the texture, stability, flavor retention, and shelf life of chewing gum. The safety of this type of paraffin wax for consumption makes it a reliable choice for use in food-grade applications.
Local residents of Gujarat believe that the wheat grown on a large scale in the region called Bhal derives its name from the Sanskrit word bhal, which means 'head', because the region also looks flat like a head. . It sounds strange, but in reality the land here is very flat and greenery is not visible anywhere far and wide. This wheat is also called as Bhalia wheat and Dodh Kani (Dawood Khani) or Chasia wheat or Katha wheat in the local language, which grows here only in special geographical conditions. This long grain wheat is one and a half times longer than other varieties of wheat. It does not require irrigation or rain water to grow, for this the moisture stored in the soil and winter dew is enough. Bhalia wheat is cultivated in the areas of Ahmedabad, Bhavnagar and Khambat in Gujarat. Local residents say that this wheat has been cultivated for centuries without irrigation, that is, only with the conserved moisture in the soil. It grows well in rainwater drained, light or medium black soils, in Bhal and its adjoining coastal areas. During the rainy season, farmers build bunds 45 to 60 cm high around the fields to collect rainwater. After the monsoon is over, the plowing of the land is done with the help of oxen. This process is repeated again to create a finer soil layer, called a penh, which acts as a layer of grass in the soil to retain soil moisture. Usually sowing is done in late October or early November. Wheat does not get rainwater nor is it irrigated after sowing, but it continues to flourish under these conditions. It is harvested with a laugh. A threshing machine is used to remove the peel on top of it or a truck is driven over them. These are thoroughly dried before storage, as the storage life of grain depends on its moisture content (less than 10% moisture is preferred). This high quality wheat is considered the best in Gujarat due to its exquisite taste and rich protein content. This wheat absorbs oil and water in small amounts and is also an insect repellent due to its unique quality. Whole wheat being hard grained, rich in protein and high in carotene content, it is used in abundance for making rava, pasta, macaroni, spaghetti and vermicelli. This wheat is consumed in the form of bhakri and chapati. Laddu, churma, halwa and thuli are also made from it due to the high soluble sugar in it. About 1.7-1.8 lakh tonnes of wheat is produced annually in 2 lakh hectares of land. The farmers of Bhal region get 25 per cent premium over other wheat varieties and 40-50 per cent higher price as compared to ordinary wheat varieties. Bhalia wheat, which is sold under the name Gujarat's wheat (GW)-1, got Geographical Indication Tag (GI) in 2011 due to its high variety, taste and distinctive qualities.
Physical and Chemical Properties 1 4butanediol is a colorless oil liquid flammable melting point 201 boiling point 235flash point open cup 121 relative density 10171204 refractive index 14461 viscosity 25 715mPas It is hygroscopic miscible with water soluble in methanol ethanol acetone slightly soluble in ether The smell is bitter but the taste is slightly sweet With strong reactivity it can carry out oxidation dehydration replacement polymerization amination esterification halogenation and other chemical reactions to produce a series of important chemical products 14butanediol Uses 1 4butanediol is an important organic chemical and fine chemical raw material which is the basic raw material for the production of polybutanediol terephthalate PBT engineering plastics and PBT fiber PBT plastic is one of the five most promising engineering plastics 14butanediol is the main raw material for the production of tetrahydrofuran tetrahydrofuran is an important organic solvent The PTMEG obtained by polymerization is the basic raw material for the production of high elasticity spandex Lycra fiber Spandex is mainly used in the production of high class sportswear swimming suits and other high elasticity knitwear Gammabutyrolactone the downstream product of 1 4butanediol is the raw material for the production of 2pyrrolidinone and NMethylpyrrolidone products From this a series of high valueadded products such as NVinyl2Pyrrolidinone and Polyvinylpyrrolidone are derived which are widely used in the fields of pesticides medicine and cosmetics 14butanediol is also widely used as solvent pharmaceutical cosmetics plasticizer hardener pesticide herbicide foam leather fiber engineering plastics and so on 1 4butanediol BDO uses Manufacturing Process of 14butanediol 1 4butynediol was prepared by acetylene and formaldehyde in the presence of catalyst and then by catalytic hydrogenation to produce 1 4butanediol It can also be prepared by the reaction of 1 3butadiene with acetic acid and oxygen through acetyl oxidation hydrogenation hydrolysis etc
