In-circuit Test Probe Pogo Pin PICT75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PICT75� series here. Its� diameter is 1 mm� and the total length is 21 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly four types of receptacles, namely CR, SC, CRW� and SW� to fit each test probe.� For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 150 milliohms Full Stroke: 4 mm Rated Stroke: 2.65 mm Spring Force:� 130 gf (4.5 oz) at load 2.65 mm Materials Contact Barrel: Phosphor Bronze, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin PE50 for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits.
Double-ended Pogo Pin Test Probe SCPA100 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA100 Â we will introduce is 1 Â mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Â Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production.
High-Current Probe Pogo Pin P203 for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P203. This probe can withstand the current up to 17 Amps. And its typical maximum contact resistance is 80 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of phosphor bronze. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 17 amps, continuous Contact Resistance: 80 milliohms, max Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 115 gf (4 oz) at load 4.3 mm Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPB038 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCFB038 we will introduce is 0.38 mm in barrel diameter and 6 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.6 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.6 mm, the loaded force is about 25 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 100 milliohms max Bandwidth: 5.3 GHz at -1dB Propagation Delay: 27 ps Inductance: 1MHZ at -0.02809 uH Captance: 1MHZ at 0.876347 uF Specifications: Full Stroke: 1 mm Rated Stroke: 0.6 mm Spring Force: 25 7 gf at load 0.6 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring Loaded Pogo Pin Test Probe BIP68 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP68 series of battery contact probes. The outside diameter is usually 0.68 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 0.95 mm (37 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 0.5 mm Rated Stroke: 0.4 mm Spring Force: 10 gf (0.35 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin PE75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE75 series here. Its test center is 75 mil. The diameter is 1.91 mm and the total length is 33.1 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.4 mm Rated Stroke: 4.3 mm Spring Force: 150 gf (5.5 oz)/200 gf (7.2 oz)/227 gf (8 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Nickel Plated or Gold Plated semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP47 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP47 series of battery contact probes. The outside diameter is usually 1.6 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 20 milliohms (Maximum) Full Stroke: 1.5 mm Rated Stroke: 1.5 mm Spring Force: 80 gf (2.8 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Spring-Loaded Pogo Pin SCPA031(21) for Chip Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA031(21) we will introduce is 0.31 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2 Amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 0.7 mm. But it is better to be pressed at a distance of 0.45 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.45 mm, the loaded force is about 20 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 2 amps Contact Resistance: 100 milliohms max Bandwidth: 7.4 GHz at -1dB Inductance: 1MHZ at -0.05996 uH Captance: 1MHZ at 0.425647 uF Specifications: Full Stroke: 0.7 mm Rated Stroke: 0.45 mm Spring Force: 20�?�±6 gf at load 0.45 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCFE035 for Integrated Circuit Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCFE035 we will introduce is 0.35 mm in barrel diameter and 18 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold The bottom plunger is made from SK4 plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 150 milliohms. The plunger can be pressed at a distance of up to 1.5 mm. But it is better to be pressed at a distance of 1 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 1 mm, the loaded force is about 38 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: SK4, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 150 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.05517 uH Captance: 1MHZ at 0.462432 uF Specifications: Full Stroke: 1.5 mm Rated Stroke: 1 mm Spring Force: 38�?�±11 gf at load 1 mm Mechanical Life: about 200000 cycles For more information, please check below catalog. Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Cable Harness Probe Pogo Pin CHZ199 Series for Electronic Test Harness probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHZ199 harness probe we will introduce here is 1.99 mm in diameter and 33.2 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.4 mm at most when this probe works, although the plunger can move as far as 6.6 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.4 mm, its loaded force is about 133 gf, namely 4.7 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.6 mm Rated Stroke: 4.4 mm Spring Force: 133�?�±40 gf (4.7 oz) at load 4.4 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Battery Contact Probe Test Pogo Pin BIP148 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP148 series of battery contact probes. The outside diameter is usually 1.49 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.16 mm (85 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 2 mm Rated Stroke: 1.33 mm Spring Force: 25 gf (1/ 0.9 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin Test Probe BIP114 Series for Battery Contact Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP114 series of battery contact probes. The outside diameter is usually 1.14 mm and there are some common tip styles, for example round head or pointed head. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms (Maximum) Full Stroke: 1.14 mm Rated Stroke: 1.14 mm Spring Force: 110 gf (4 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: BeCu, Gold Plated Company information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Test Probe Pogo Pin SCPA020 for Integrated Circuit Inspection Semiconductor test probes are usually called double-ended pogo pins.  Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPA020 we will introduce is 0.2 mm in barrel diameter. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. � Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold or gold clad phosphor bronze. The bottome plunger is made from SK4 plated with nickel and gold. The same is with the top plunger. The inner spring is made from SUS304 plated with gold and nickel. This probe pin could withstand the current up to 1 Amp. The typical maximal contact resistance is about 200 milliohms The plunger can be pressed at a distance of up to 1.1 mm. But it is better to be pressed at a distance of 0.6 mm at most in working environments. Otherwise the spring will probably be damaged severely under constanct pressure. When the plunger is pressed at a distance of 0.6 mm, the loaded force is about 12 gf, which fluctuates to a tolerane. For details, please check parameters in below table. Materials (plated) Barrel: Ph/ SP, Au on Ni Plated Bottom Plunger: SK4, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP  Au on Ni Plated Electronic Specification: Current Rating: 1 amp Contact Resistance: 200 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.13527uH Captance: 1MHZ at 0.186437uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.6 mm Spring Force: 12 ±4 gf at load 0.6 mm Mechanical Life: about 100000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. Welcome to browse our website centalic.com and download any catalogs of our products.
Electronic Test Probe Double-sided Spring Pogo Pin SCPA057 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. SCPA057 series is a medium-sized one in all semiconductor test probes. Both plungers are movable. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Ph, Au on Ni Plated Bottom Plunger: BeCu, Au on Ni Plated Top Plunger: BeCu, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 3 Amps Contact Resistance: 100 milliohms, max Bandwidth: 5 GHz at -1dB Propagation Delay: 24 ps Inductance: 1MHZ at -0.03664 uH Captance: 1MHZ at -0.704638 uF Specifications: Full Stroke: 0.63 mm Rated Stroke: 0.5 mm Spring Force: 45 ±13 gf at load 0.5 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Double-ended Pogo Pin SCPE015 for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPE015 is the tiniest series in semiconductor test probes since its outside diameter is only 0.15mm. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices  Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Gold Clad, No Plated X-Bottom (Plunger 1): Pd, No Plated Y-Top (Plunger 2): Pd, No Plated Spring: SWP, Au on Ni Plated Electronic Specification: Current Rating: 0.5 amp Contact Resistance: 250 milliohms max Bandwidth: 11.4 GHz@-1dB Inductance: 1MHZ@-0.06439uH Captance: 1MHZ@0.364375uF Specifications: Full Stroke: 0.8 mm Rated Stroke: 0.6 mm Spring Force: 9 ±2 gf@load 0.6 mm Mechanical Life: about 100000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
CPI -1507 series products are polyalkylene glycol lubricants, formulated to give negligible solubility or dilution in contact with hydrocarbon liquids or vapors. The ability of these lubricants to withstand dilution by hydrocarbon gases is particularly advantageous in compressors handling high concentrations of hydrocarbon and gasoline vapors. Applications include lubricating mechanical seals, centrifugal compressors, and scroll compressors. CPI-1507 series products are heat stable polymers in the absence of oxygen. They are soluble in water. Test Procedure CPI-1507-32 Viscosity @ 40C, cSt, ASTM D445 31.72 Viscosity @ 100C, cSt 5.28 Viscosity @ 100F, SUS 165.0 Viscosity @ 210F, SUS 44.0 Viscosity Index, ASTM D2270 96 Density, lb/gal, 60F, ASTM D4052 9.43 Pour Point F (C), ASTM D97 -49 (-56.2) Flash Point, C.O.C., F (C), ASTM D92 350 (177) Fire Point, C.O.C.,F (C), ASTM D92 355 (179) Specific Gravity, ASTM D4052 1.130 These are typical values and are not intended for use in preparing specifications
CPI-1507 series products are polyalkylene glycol lubricants, formulated to give negligible solubility or dilution in contact with hydrocarbon liquids or vapors. The ability of these lubricants to withstand dilution by hydrocarbon gases is particularly advantageous in compressors handling high concentrations of hydrocarbon and gasoline vapors. Applications include lubricating mechanical seals, centrifugal compressors, and scroll compressors. CPI -1507 series products are heat stable polymers in the absence of oxygen. They are soluble in water. Test Procedure CPI -1507-32 Viscosity @ 40 C, cSt, ASTM D445 31.72 Viscosity @ 100 C, cSt 5.28 Viscosity @ 100 F, SUS 165.0 Viscosity @ 210 F, SUS 44.0 Viscosity Index, ASTM D2270 96 Density, lb/gal, 60 F, ASTM D4052 9.43 Pour Point F ( C), ASTM D97 -49 (-56.2) Flash Point, C.O.C., F ( C), ASTM D92 350 (177) Fire Point, C.O.C., F ( C), ASTM D92 355 (179) Specific Gravity, ASTM D4052 1.130 These are typical values and are not intended for use in preparing specifications.
CPI -1507 series products are polyalkylene glycol lubricants, formulated to give negligible solubility or dilution in contact with hydrocarbon liquids or vapors. The ability of these lubricants to withstand dilution by hydrocarbon gases is particularly advantageous in compressors handling high concentrations of hydrocarbon and gasoline vapors. Applications include lubricating mechanical seals, centrifugal compressors, and scroll compressors. CPI -1507 series products are heat stable polymers in the absence of oxygen. They are soluble in water. Test Procedure CPI -1507-32 Viscosity @ 40 C, cSt, ASTM D445 31.72 Viscosity @ 100 C, cSt 5.28 Viscosity @ 100 F, SUS 165.0 Viscosity @ 210 F, SUS 44.0 Viscosity Index, ASTM D2270 96 Density, lb/gal, 60 F, ASTM D4052 9.43 Pour Point F ( C), ASTM D97 -49 (-56.2) Flash Point, C.O.C., F ( C), ASTM D92 350 (177) Fire Point, C.O.C., F ( C), ASTM D92 355 (179) Specific Gravity, ASTM D4052 1.130 These are typical values and are not intended for use in preparing specifications.
Essential details: Condition: New Warranty: Unavailable Applicable Industries: Manufacturing Plant, Farms, Construction works , Other Weight (KG): 0.05 KG Showroom Location: India Video outgoing-inspection: Not Available Machinery Test Report: Not Available Marketing Type: New Product 2020 Type: Other Use: Tractors Place of Origin: Punjab, India Brand Name: MK After Warranty Service: No service Local Service Location: India Product Name: linch pin Application: Farm Tractor Material: Steel Usage: Tractor Implement Farm Machine Size: Standard Size Name: Agricuture Tyre OEM: Accepable Model Number: Diesel Engine Made Supply Ability: 1000 Piece/Pieces per Month Packaging Details As per order quantity and customer demand. Port: NAVASHIVA
