Spring Pin Battery Contact Probe BIP85 Series for Connector Application Battery contact probes are characterized by excellent conductivity, low resistance and high stability. They are mainly used for contact, connection and conduction, for example they can be used for connecting batteries or other electrical components. Battery contact probes are made from high-end materials. The specifications, outside diameters and tip styles vary considerably from probe to probe. Many common models are always kept in stock so as to meet the needs of various industries for bulk orders. A battery contact probe is often comprised of a barrel, a plunger and a spring. The barrel is usually manufactured from brass and phosphor bronze is an alternative for customization. The spring is often made from music wire and stainless steel is an alternative. The plunger is made from beryllium copper and high carbon steel is a custom-made choice. A whole probe is plated with gold in order to strengthen the conductivity. The products in this page are classified into BIP85 series of battery contact probes. The outside diameter is usually 0.85 mm and there are some common tip styles, for example J. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms (Maximum) Full Stroke: 0.5/1.5 mm Rated Stroke: 0.34/1 mm Spring Force: 28/ 48 gf (1/ 1.78 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Gold Plated radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
High-current Probe Pogo Pin P265 Series for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P265. This probe can withstand the current up to 24 Amps. And its typical maximum contact resistance is 50 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of brass. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated stainless steel. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 24 amps, continuous Contact Resistance: 50 milliohms, max Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 220 gf (7 oz) at load 3.5 mm Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Printed Circuit Board Assembly Test Probe Pogo Pin PQ75 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQ75 series here. Its test center is 75 mil. The diameter is 1.02 mm and the total length is 33.02 mm. Various tip styles, for example, H, K, L, BK, etc., are available for test probes. There are three types of receptacles, namely CR, SC and WW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 112/150/198 gf (4/5.5/7 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Single-headed Pogo Pin Test Probe PQ50 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQ50 series here. Its diameter is 0.78 mm and the total length is 34.6 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 60 milliohms Mounting Hole Size: Diameter 1 mm Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 85 gf (3 oz) /122 gf (4 oz)/ 150 gf (5.5 oz) at load 4.3 mm Materials Receptacle: Phosphor Bronze, Au on Ni Plated Contact Barrel: Phosphor Bronze, Au on Ni Plated Spring: Music Wire, Au on Ni Plated Plunger: Beryllium Copper, Gold Plated or Nickel Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Wire Harness Probe Pogo Pin CHD136 for the Tests of Automotive Industry Harness probes are mainly used directly or for the tests of the automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. The standard and requirements for them are high compared with other test probes. Harness probes can be divided into screw-thread harness probes, harness switch probes, non-screw-thread harness probes, position-limited harness probes and high-current harness probes, etc. The CHD136 harness probe we will introduce here is 1.36 mm in diameter and 33 mm in total length. Its barrel is made of brass plated with gold and nickel. The plunger is made of gold-plated beryllium copper, which is softer but less magnetic than the alternative SK4. The spring inside is made of music wire plated with gold and nickel. This probe can withstand up to the current 3 Amps. Its typical maximum contact resistance is 50 milliohms. It is suggested the plunger be pressed at a distance of 4.6 mm at most when this probe works, although the plunger can move as far as 7 mm. Otherwise, the spring inside the barrel will probably be damaged under constant pressure. When the plunger is pressed at a distance of 4.6 mm, its loaded force is about 255 gf, namely 9 ounces or so. Furthermore, the force fluctuates in a range due to the tolerance. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 7 mm Rated Stroke: 4.6 mm Spring Force: 255�±75 gf (9 oz) at load 4.6 mm Materials (plated) Barrel: Brass, Au on Ni Plated Plunger: Beryllium Copper, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Double-ended Pogo Pin Test Probe SCPA058 Series for Semiconductor Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. SCPA058 series is a medium-sized one in all semiconductor test probes. Both plungers are movable. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. Its parameters are as below. Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: Beryllium Copper, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 3.5 Amps Contact Resistance: 100 milliohms, max Bandwidth: 8.5 GHz at -1dB Propagation Delay: 21 ps Inductive Reactance: 1MHZ at -0.02506 uH Capacitive Reactance: 1MHZ at -1.01245 uF Specifications: Full Stroke: 1.1 mm Rated Stroke: 0.65 mm Spring Force: 25�±7 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Gold Plated Pogo Pin PCBA Probe PE75(PO) Series for In-circuit Test In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE75(PO) series here. Its test center is 75 mil. The diameter is 1 mm and the total length is 33 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 40 milliohms Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 155 gf (5.5 oz)/203 gf (7.2 oz)/227 gf (8 oz)/300 gf (10 oz) Materials Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Electronic Test Probe Pogo Pin PSICT39 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PSICT39 series here. The diameter is 0.61 mm and the total length is 19.5 mm. Various tip styles, for example, B, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 70 milliohms Full Stroke: 4 mm Rated Stroke: 2.5 mm Spring Force: 70 gf (2.5 oz) at load 2.5 mm Materials Receptacle: Brass, Au on Ni Plated Contact Barrel: Phosphor Bronze, Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: BeCu, Au on Ni Plated For more information, please check below catalog. Company Information Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals.
In-circuit Test Probe Pogo Pin P078 Series for Printed Circuit Board Assembly In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe P078-BK-346 series here. The diameter is 0.78 mm and the total length is 34.6 mm. Various tip styles, for example, BK, H, S, T, E, C, U, G, etc., are available for test probes. For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.9 mm Rated Stroke: 4.6 mm Spring Force: 200 gf (7 oz) at load 4.6 mm Materials Contact Barrel: Phosphor Bronze, Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: SK4, Au on Ni Plated Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
PCBA Test Probe Pogo Pin PL75 Series Applied to ICT In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PL75 series here. Its test center is 75 mil. The diameter is 1.02 mm and the total length is 27.83 mm. Various tip styles, for example, H, K, L, BK, etc., are available for test probes. There are roughly six types of receptacles, namely CR, VCR, SC, VSC, WW and VWW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.91 mm (75 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Mounting Hole Size: Diameter 1.35 mm Full Stroke: 4 mm Rated Stroke: 2.54 mm Spring Force: 113 gf (4 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper/SK4, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Spring-loaded Pogo Pin In-circuit Test Probe PICT102-BK(7.6) for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PICT102-BK(7.6) series here. Its barrel diameter is 1.02 mm and the total length is 33 mm. The barrel of this pogo pin is made from phosphor bronze plated with gold and nickel. The plunger is made from SK4 plated with nickel and gold. The inner spring is made from music wire plated with gold and nickel. This test probe could withstand the current up to 3 Amps. The typical maximal contact resistance is about 50 milliohms. The plunger can be pressed at a distance of up to 6.8 mm. But it is better to be pressed at a distance of 4.3 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 4.3 mm, the loaded force is about 205 gf, which fluctuates to a tolerance. For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Full Stroke: 6.8 mm Rated Stroke: 4.3 mm Spring Force: 205 gf (7 oz) at load 4.3 mm Materials Contact Barrel: Phosphor Bronze, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: SK4, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Spring-loaded Pogo Pin PE100(115) for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE100(115) series here. Its test center is 100 mil. The diameter is 1.36 mm and the total length is 36.5 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 30 milliohms Mounting Hole Size: Diameter 1.75 mm Full Stroke: 6.5 mm Rated Stroke: 4.3 mm Spring Force: 200 gf (7.2 oz)/255 gf (9 oz)/284 gf (10 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Switch Probe Test Pogo Pin SWP137 Series for Connection Switching Probes is a kind of functional probes.They are used to determine the correct location of a terminal in a connector. They can also be used to determine the presence of nonconductive components, etc. Their application field is mainly as below Wire harness connector PCB component detection Door open-close switch Fixture component detection Automation process sensing Position and retention force Below switching probe we will introduce is SWP137. Its diameter is 1.37 mm and total length is 30.75 mm. As usual, switching probes do not entail very high currents, and this model SWP137 can work with the current up to 3 A. The typical maximum contact resistance of this model SWP137 is 80 m . The materials used for the construction of switching probes are different for each component: The barrel  is made of brass. Subsequently nickel  plated during the galvanic plating phase. probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website  and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Gold Plated Switch Probe Test Pogo Pin SWP260 Series for Connection Switching Probes is a kind of functional probes. They are used to determine the correct location of a terminal in a connector. They can also be used to determine the presence of nonconductive components, etc. Their application field is mainly as below Wire harness connector PCB component detection Door open-close switch Fixture component detection Automation process sensing Position and retention force Below switching probe we will introduce i As usual, switching probes do not entail very high currents, and this model SWP260 can work with the current up to 3 A. SWP260  is 50 m The materials used for the construction of switching probes are different for each component: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website  and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Interface Probe Test Pin IFP-001 Used for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-001, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-001 interface probe is 14.22 mm in total length. If customers wish to change its length or diameter, we could do as required. This probe is unique in shape. It is straight whereas others, for example 002, 003, 004, 005, 006, 007, have an extra base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information was founded in 1980. Â Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
Interface Probe Test Pin IFP-007 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-007, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-007 interface probe is 40.05 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
In-circuit Test Probe Pogo Pin PICT75 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PICT75� series here. Its� diameter is 1 mm� and the total length is 21 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly four types of receptacles, namely CR, SC, CRW� and SW� to fit each test probe.� For details, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 150 milliohms Full Stroke: 4 mm Rated Stroke: 2.65 mm Spring Force:� 130 gf (4.5 oz) at load 2.65 mm Materials Contact Barrel: Phosphor Bronze, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Plunger: BeCu, Au on Ni Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
High-Current Probe Pogo Pin P203 for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P203. This probe can withstand the current up to 17 Amps. And its typical maximum contact resistance is 80 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of phosphor bronze. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 17 amps, continuous Contact Resistance: 80 milliohms, max Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 115 gf (4 oz) at load 4.3 mm Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Interface Probe Test Pin IFP-004 for Transmitting Electrical Signals Interface probes are functional probes. They are not used for tests and only play a role in connection or control in switching functions, etc. Interface probes are used for transmitting electrical signals from one end to the other end in test fixtures. Interface probes manufactured by Centalic mainly include the models 001, 002, 003, 004, 005, 006 and 007 in IFP series. This product, IFP-004, is made from phosphor bronze or brass, plated with gold. Characterized by excellent conductivity, it is usually used for the connection of electronic components and functional tests. IFP-004 interface probe is 17.8 mm in total length. If customers wish to change its length or diameter, we could do as required. Unlike IFP-001, it has a base at the end. If the gold plating is expected to be thicken or thinned, we could try to do according to requirements. Customization is welcome. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Welcome to browse our website and download any catalogs of our products. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal
High-Current Probe Pogo Pin P350(150) for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P350(150)-H-14G(C) This probe can withstand the current up to 20 Amps. And its typical maximum contact resistance is 50 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of brass. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of SK4, then gold and nickel plated. The plunger tip is made of brass, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 20 amps, continuous Contact Resistance: 50 millohms, max Full Stroke: 7.5 mm Rated Stroke: 5 mm Spring Force: 397 gf at load 5 mm Company Information: in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
