Vacuum Membrane Press Suppliers and Manufacturers

Technical data of the machine Working area dimension 2350 x 1250 x 60 mm. Maximum pressure 210 ton – 6 kg / cm¦ Surface pressure 160 ton – 5 kg / cm¦ Gradual pressure characteristics Electronic Vacuum pressure 28 ton – 750 milibar Vacuum capacity 100 m¦/h Vacuum motor power 3 kw – 1400 rpm (2 motors) Pressing motor characteristics 1.1 kw – 2800 rpm Resistance heating power 18 x 1000 w Air resistance 4 x 1000 w Air pressure 6 bar Total power 30 kw, 380v , 50hz Machine body dimensions 2000 (w) x 2020 (h) x 2900(l) Pressing plate dimensions 1700 (w) x 1090 (h) x 3350(l) Machine’s total weight 5 ton

3 Unit Working Table I.Table Outer Dimensions, 2800x1400mm II.Table Outer Dimensions , 2400x1400mm III.Table Outer Dimensions , 1200x1400mm Automatic Moving Turbine Manuel and Automatic Control Fault Control Section Waiting Station Special Design Mold System Temperature Measurement Unit , Infrared Sensor 3-4 min Operation Time Audible-Visual Fault Warning System Phase Protection Leakage Relay 29 Kw Heater Energy Consumption 30 Kw Total Energy Consumption Schneider-Delta Electrical-Electronical System 63 m³/Hour Vacuum Pump 71 Dba Noise Level 1950 Kg Machine Weight 9320mm Machine Length 1795mm Machine Width 1450mm Machine Height

3 unit working table I.Table outer dimensions, 2800x1400mm II.Table outer dimensions , 2400x1400mm III.Table outer dimensions , 1200x1400mm Automatic moving turbine Manuel and automatic control Fault control section Waiting station Special design mold system Temperature measurement unit , infrared sensor 3-4 min operation time Audible-visual fault warning system Phase protection Leakage relay 29 KW heater energy consumption 30 KW total energy consumption Schneider-delta electrical-electronical system 63 m³/hour vacuum pump 71 dba noise level 1950 kg machine weight 9320mm machine length 1795mm machine width 1450mm machine height. 1950 kg.

Technical Specifications : Exterior size :10030mm, 2230 mm, 2150mm Working plate size:2580mm, 1270mm inner size Suitable for cabinet, the width of PVC film should be 1400mm Maximum height of the work piece :50mm including bottom plate Rating working pressure: Positive pressure 0.6Mpa Negative pressure : -0.095Mpa General Power: 65kw Actual power consumption : About 15kw Weight :12.6T Top temperature:150 EPE film+preservative film, 3.25x2.25x2.05m+2.3x1.25x1.8m 12000kg.

Applicable covering material: pvc, natural veneer, transfer Sphere of application: It is intended for laminate doors, kitchen and furniture facades, different furniture units with pvc films and veneer, with the help of heat and vacuum technique system. As result you will receive product with long life use and the same time with elegant and inclusive surface.It is applicable to cover plate type furniture (sound box, cabinet, door), decorative dado and all kinds of baroque decorative surfaces with pvc films and wood skins and hot stamping foils. Technical parameters: 1) external dimensions: 9, 000 x 1, 800 x 1, 300mm 2) worktable dimensions: 2, 550 x 1, 150 (1, 300) x 50mm 3) max. Processing height: 80mm 4) pvc thickness:0.1-0.35mm; 5)max vacuum press:-0.1mpa; 6) total power: 20kw 7) actual power:5kw 8)total weight: 3, 000kg Features: 1. This machine has 2 work table, the electronic part is fully automatic and digitalized control. The components are produced by famous domestic enterprises with good quality. The temperature is controlled by computer chips so that the heating speed is adjustable and the temperature can be perfectly managed. 2. Use infrared heating system and high quality heat preservation material, which can ensure even heating and energy saving. 3. This machine uses integrated movement electromotor. It produces less noise and seldom breaks down. 4. This machine uses top 2x series vacuum pump. It is stable and reliable and the maintenance work is simple. (you can also adopt for german-made vacuum pump, which is strong and tough). 5. Large volume vacuum tank. It charges with double channels so that it can work with strong power. Wood

It fully demonstrates that the equipment can be used rationally and pleasantly. Fully take equipment structural,materials,and other conditions into consideration,so the operator's working gesture is more in line with the the principle of ergonomics, to provide workers with a comfortable and safe working environment,to reach an optimize efficiency. This machine is equipped with automatic locking device, Press film covering device, automatic table running device and so on.  The process is smooth and tightly one-stop production. The machine is highly automation and is easy to operate. The warehouse is automatically operated and transmissed. The processing time, temperature and vacuum degree of the workpiece are automatically controlled by digital display, so that the function of high-gloss PVC is achieved. The heating system is heated by aluminum plate, so it can matain a  uniform strength heat, thereby improved the percentage of qualified products.  This high-performance membrane press machine developed by our technicians from studing the characteristics of PVC film. It solves the problem that ordinary positive and negative press machine can not properly dealing high-glossy workpiece.  This machine adopts unique heating process, large processing work-surface , which can both greatly improves production efficiency and saves cost;  the transmission system leases chain drive, adopts two-stage deceleration to prevent misalignment, avoid product wasting; computer system adopts imported electrical appliances with stable work performance , equipped with manual operation procedures with high degree of automation. This machine equiped with the largest worktable area in Asia. Cindy Lee Shenyang Zhanhongtu Machinery & Equipment Co.,Ltd WhatsApp/WeChat:ï¸?+86-15840529588                          www.zhtmachinery.com

1. The whole machine adopts Italian technology and the operation is stable and mature. 2. Hydraulic pressure system uses original components, which is safe and reliable and the technology is of good quality. 3. Energy saving compressed air tank is of new type and super large size with considerably great pressure. 4. PLC control interface operation system originally from Japan with advanced technology and highly automatic. 5. Adopt Germany Vacuum Pump, features strong horsepower, reliable and fast recorery. 10080*2400*2180mm.

1.Fast speed: The working period of ordinary workpiece is less than 2 minutes after it enters the main machine, which is 2-4 times of the efficiency of common positive and negative pressure membrane pressure equipment. 2.Good effect: The product processed by common film has clear groove, no open side, bubbling, no color difference, and high light working surface has strong adhesion, and the effect reaches the international leading level. 3.Low energy consumption: The total power of the machine is 43KW, which is one half of that of the peer equipment;The main heating starting power is 18KW, and the average power consumption is 13KW/h. 4.High configuration: The key part of the machine adopts original parts from Germany, Japan and Taiwan, which is high configuration and stable performance. 5.High working efficiency: The whole machine adopts automatic top block. Compared with other domestic manufacturers, it saves the technological process of making the pad, saves the cost of process raw materials, saves the scanning sequence of the pad of the equipment, saves the time of laminating process, greatly improves the working efficiency and reduces the labor cost. 6.High degree of automation: The machine is equipped with automatic fabric selection tilting rack, automatic film cutting device, automatic gasket device, laminating device of pressing machine, pallet lifting device and finished product rollover collection device, etc., with high degree of automation, smooth and close process and one-stop film-covering process production.The height of the top block can be selected 12, 15 and 18 mm, solving the phenomenon that the high-light sample block is not in place.

- Due to circulational cooling system the pressing process is done faster. - There are rails and locks installed on the machine in order to put on silicon membrane and to work with natural veneer. - There is an automatic film fixation mechanism, that helps save time preparing before the pressing. Also it helps prevent defects on the pressed pieces, that may arise as a consistence of wrong replacement of the film on the worktable. - Press head lifters are designed to prevent swashes of the head of the machine. -Air dispersion system provides a proportional dispersion of the air inside the machine while pressing, so the air temperature in each corner of the machine is the same. -After recent modifications the quality of covering of wood pieces with PVC has risen. -The machine is extremely easy for use, so it can be used even by low-qualified workers. -There is one machine better than this one- it is membrane-vacuum press with additional air pressure. Vacuum 40 m3/hour The dimensions of the machine 2800 x 1600 mm x 1500 mm Total power 27,5 Kw The dimension of the worktable 1400 x 2500 mm The area of the worktable used 1200 x 2300 mm The time required for pressing process (up to material) 2-20 min. Circulational cooling system The system of automaic fixing of PVC or similar materials. Automatic vacuum system Weight 600 кg

Technical Specifications : Exterior size: 5800(Double plate 8800) mm, 1500 mm, 1400mm Working plate inner size: 2550mm, 1150 1300 mm (if producing the door, you choose 1150mm;if producing cabinet, you choose 1300mm) Maximum height of the work piece:50mmincluding height of Magnetic block or bottom plate Rating working pressure: -0.095Mpa General Power: 15kw Actual power consumption: about 5kw Weight: 2.5T Top temperature:180. EPE film+preservative film 3.2X1.8X2M 2500KG.

Maps Vacuum press are proven method of PVC foiling on MDF and HDF surfaces. The Maps vacuum press vista is ideal machine for small and medium sized industry. The machine is loaded with full off features. Our machines are designed to consume the minimal power consumption at the same time you get the best result in its class.The mahine doesn't have any hydraulic or pneumatic components which eliminates the high maintanence. Technical Specifications: Sl.No Technical Specification Amt Unit 1 Usable Area 2400 x 1250 mm 2 Max Height of Product 65 mm 3 Max Pressure 2.5 T/m² 4 Foil Width 1400 mm 5 Total Connected Load 14 kw 6 Heating Quartz Tube Heating 7 Dimension 6 x 1.9 x 1.87 mtr 8 Weight 2000 Kg 9 Input 440 V3 Phase Features: 1 Quartz tubular heating for uniform heating and low energy consumtion 2 German make vacuum pump for high efficiency 3 No air connection reqd 4 Grooved bed for placing the product in line with grains of foil 5 see through panel to monitor the process 6 Easily upgraded for double tray 7 Membrane less operation 8 Ease of use 9 Materials like PVC,PP,KYDEX,Polyolefin and high gloss also possible. Applications: 1 Kitchen cabinets 2 Wardrope doors 3 Office furnitures 4 Work station table tops 5 Cabinates 6 Plastic components 7 Flush doors. Nylon wrapping with wooden pallet.

Features: 1.In virtue of the generation-changing ,new concept up arading of themachine, high configuration,and good price ,we get widely praised. 2.Economize material .(exsample :economize at least 0.6 M2 each face .total save 5-6RMB PVC material . 3.Adopting Low temperature and high pressure to protect the PVC colour 4.More clean line-frame ,and lasting bonding 5.It can past wooden venner on vairous materials. 6600*2140*2150mm.in nude.

1. The heating system adopts Germanic strip heater technology, it can efficient energy. 2. Hydraulic pressure system uses original components, which is safe and reliable and the technology is of good quality. 3. Energy saving compressed air tank is of new type and super large size with considerably great pressure. 4. Adopt Germany Vacuum Pump, features strong horsepower, reliable and fast recorery. 5.It especially paste in high gloss PVC.