- Due to circulational cooling system the pressing process is done faster.
- There are rails and locks installed on the machine in order to put on silicon membrane and to work with natural veneer.
- There is an automatic film fixation mechanism, that helps save time preparing before the pressing. Also it helps prevent defects on the pressed pieces, that may arise as a consistence of wrong replacement of the film on the worktable.
- Press head lifters are designed to prevent swashes of the head of the machine.
-Air dispersion system provides a proportional dispersion of the air inside the machine while pressing, so the air temperature in each corner of the machine is the same.
-After recent modifications the quality of covering of wood pieces with PVC has risen.
-The machine is extremely easy for use, so it can be used even by low-qualified workers.
-There is one machine better than this one- it is membrane-vacuum press with additional air pressure.
Vacuum 40 m3/hour
The dimensions of the machine
2800 x 1600 mm x 1500 mm
Total power 27,5 Kw
The dimension of the worktable 1400 x 2500 mm
The area of the worktable used 1200 x 2300 mm
The time required for pressing process (up to material) 2-20 min.
Circulational cooling system
The system of automaic fixing of PVC or similar materials.
Automatic vacuum system
Weight 600 кg
3 Unit Working Table I.Table Outer Dimensions, 2800x1400mm II.Table Outer Dimensions , 2400x1400mm III.Table Outer Dimensions , 1200x1400mm Automatic Moving Turbine Manuel and Automatic Control Fault Control Section Waiting Station Special Design Mold System Temperature Measurement Unit , Infrared Sensor 3-4 min Operation Time Audible-Visual Fault Warning System Phase Protection Leakage Relay 29 Kw Heater Energy Consumption 30 Kw Total Energy Consumption Schneider-Delta Electrical-Electronical System 63 m³/Hour Vacuum Pump 71 Dba Noise Level 1950 Kg Machine Weight 9320mm Machine Length 1795mm Machine Width 1450mm Machine Height
3 unit working table I.Table outer dimensions, 2800x1400mm II.Table outer dimensions , 2400x1400mm III.Table outer dimensions , 1200x1400mm Automatic moving turbine Manuel and automatic control Fault control section Waiting station Special design mold system Temperature measurement unit , infrared sensor 3-4 min operation time Audible-visual fault warning system Phase protection Leakage relay 29 KW heater energy consumption 30 KW total energy consumption Schneider-delta electrical-electronical system 63 m³/hour vacuum pump 71 dba noise level 1950 kg machine weight 9320mm machine length 1795mm machine width 1450mm machine height. 1950 kg.
Applicable covering material: pvc, natural veneer, transfer Sphere of application: It is intended for laminate doors, kitchen and furniture facades, different furniture units with pvc films and veneer, with the help of heat and vacuum technique system. As result you will receive product with long life use and the same time with elegant and inclusive surface.It is applicable to cover plate type furniture (sound box, cabinet, door), decorative dado and all kinds of baroque decorative surfaces with pvc films and wood skins and hot stamping foils. Technical parameters: 1) external dimensions: 9, 000 x 1, 800 x 1, 300mm 2) worktable dimensions: 2, 550 x 1, 150 (1, 300) x 50mm 3) max. Processing height: 80mm 4) pvc thickness:0.1-0.35mm; 5)max vacuum press:-0.1mpa; 6) total power: 20kw 7) actual power:5kw 8)total weight: 3, 000kg Features: 1. This machine has 2 work table, the electronic part is fully automatic and digitalized control. The components are produced by famous domestic enterprises with good quality. The temperature is controlled by computer chips so that the heating speed is adjustable and the temperature can be perfectly managed. 2. Use infrared heating system and high quality heat preservation material, which can ensure even heating and energy saving. 3. This machine uses integrated movement electromotor. It produces less noise and seldom breaks down. 4. This machine uses top 2x series vacuum pump. It is stable and reliable and the maintenance work is simple. (you can also adopt for german-made vacuum pump, which is strong and tough). 5. Large volume vacuum tank. It charges with double channels so that it can work with strong power. Wood
The polyester staple fiber machine (PSF plant) takes virgin PET Chips, recycled Bottle Flakes, Popcorn and Lumps, etc., as raw material, with continuous drying (or batch drying through Vacuum Dryer), high pressure melt spinning process engineering and VFD controlled Spinning & Stretching process engineering to produce normal Staple Fibre, High Tenacity Low Elongation Staple Fibre and Hollow Fibre. Single plant capacity is 15T.P.D. to 80T.P.D. Equipment Technical Data Titer Range dtex 6.67-16.67 Spinning Pos. nos. 6-24 Spinning Pitch mm 700, 750 Plant Capacity TPD 15-80 Spinneret dia. mm 328, 358, 410 Spinning Mechanical Speed m/min 500-1,500 Spinning Processing Speed m/min 500-1,300 Stretching Mechanical Speed m/min 240 Stretching Processing Speed m/min 230 Total Tow Titer at Stretching dtex 600,000-3,000,000 Stuffer Box Width mm 160-410 Cutting Length mm 25, 32, 38, 44, 51, 64, 76, 101 Bale Weight kg 200-350 Application: Cushions Pillows Quilts Toys Jacket Mattress Non woven carpet Automotive felts, speaker felts, geo textiles, polyfill wadding, filter fabrics and other acoustics as well. Spinning Line: Continuous Dryer Hopper Screw Extruder Polymer Pipe Filter Spin Beam (Meter Pump System, Spin Pack, Spinneret) Quenching Unit Interfloor Duct Draw-off Wall Capstan Roller Sunflower Gearing Unit Automatic Fiber Can Device Drawing line: Can Creel Inlet Thread Guide Tow Guide Stand Dipping Bath 1st Draw Stand Draw Bath 2nd Draw Stand Draw Steam Chest 3rd Draw Stand Tow Stacker Crimper Steam Box Crimper Silicone Oil Sprayer Machine Tow Tension Stand Cutter Fiber Spreading Machine Relaxer Fiber Blowing system Baling Press
1.Fast speed: The working period of ordinary workpiece is less than 2 minutes after it enters the main machine, which is 2-4 times of the efficiency of common positive and negative pressure membrane pressure equipment. 2.Good effect: The product processed by common film has clear groove, no open side, bubbling, no color difference, and high light working surface has strong adhesion, and the effect reaches the international leading level. 3.Low energy consumption: The total power of the machine is 43KW, which is one half of that of the peer equipment;The main heating starting power is 18KW, and the average power consumption is 13KW/h. 4.High configuration: The key part of the machine adopts original parts from Germany, Japan and Taiwan, which is high configuration and stable performance. 5.High working efficiency: The whole machine adopts automatic top block. Compared with other domestic manufacturers, it saves the technological process of making the pad, saves the cost of process raw materials, saves the scanning sequence of the pad of the equipment, saves the time of laminating process, greatly improves the working efficiency and reduces the labor cost. 6.High degree of automation: The machine is equipped with automatic fabric selection tilting rack, automatic film cutting device, automatic gasket device, laminating device of pressing machine, pallet lifting device and finished product rollover collection device, etc., with high degree of automation, smooth and close process and one-stop film-covering process production.The height of the top block can be selected 12, 15 and 18 mm, solving the phenomenon that the high-light sample block is not in place.
TM2580F Positive and Negative Press Machine Features 1. Fast speed: the working period of ordinary workpiece is less than 2 minutes after it enters the main machine, which is 2-4 times of the efficiency of common positive and negative pressure membrane pressure equipment. 2. Good effect: the product processed by common film has clear groove, no open side, bubbling, no color difference, and high light working surface has strong adhesion, and the effect reaches the international leading level. 3. Low energy consumption: the total power of the machine is 28KW, which is one half of that of the peer equipment; The main heating starting power is 18KW, and the average power consumption is 10KW/h. 4. High configuration: the key part of the machine adopts original parts from Germany, Japan and Taiwan, which is high configuration and stable performance. The equipment uses imported solid core diameter 180mm cylinder to prevent oil leakage. The frame is made of manganese steel plate and sandblasted to enhance corrosion resistance and load bearing. The lifting balance system is easy to adjust, and the rise and fall are more stable. Hydraulic system oil port improvement and maintenance is more convenient. The aluminum frame is processed by one body, and no weld seam increases the strength. Outline size 11200mm*2480mm*2150mm Worktable size 2560mm*1270mm Weight 14T Total power 28KW Actual power consumption about 10KW Maximum processing size 50mm Voltage 380v 50HZ optional Rated operating pressure positive â?¤0.6Mpa negative â?¥-0.095Mpa Pls contact me Cindy Lee Shenyang Zhanhongtu Machinery & Equipment Co.,Ltd WhatsApp:+8615840529588 Wechat:15840529588
TM3000P-B Upper Pressure Machine With Pin System Feature 1.High speed The working period for making ordinary and high glossy workpieces is less than 2 minutes after it enters the main machine, which is 2-4 times of the efficiency of common positive and negative pressure membrane pressure equipment. 2.Good effect The product processed by common film has clear groove, no peeling off at sides, bubbling, no color difference, and high light working surface has strong adhesion, and the effect reaches the international leading level. 3.Low energy consumption: The total power of the model is 43KW, which is one half of that of the peer equipment;The main start heating power is 18KW. 4.High configuration The key parts of the model adopt original ones from Germany, Japan and Taiwan, which is of high configuration and of stable performance. 5.High working efficiency: The whole machine adopts automatic top block device. Compared with other domestic manufacturers, it saves the technological process of making the pads, the cost of raw materials, saves the sequence of scanning pads, as well as the time of lamination, greatly improves the working efficiency and reduces the labor cost. 6.High degree of automation The machine is equipped with automatic tilting rack for fabric selection, automatic film cutting device, automatic gasket device, laminating device of pressing machine, pallet lifting device and finished product rollover collection device, etc., with high degree of automation, it has outstanding features like smooth and close process and one-stop film-covering process production.The height of the top block can be selected 12, 15 and 18 mm, solving the issue that the high gloss sample blocks are not in place while laminating. Outline size 13500mm*5500mm*2800mm Worktable size 3000mm*1270mm Weight 18T Total power 43kw Actual power consumption 18Kw Maximum processing size 80mm Voltage 380v 50HZ optional Rated operating pressure positive pressure0.6Mpa, negative pressure-0.095Mpa
With this machine, you no longer have to worry about the slow place of the backing board. You will get greater benefits. Which will allow you to increase production efficiency. Which means that you save costs.
After the upgrade, the full automatic pin system vacuum membrane press machine does not require manual placing of the backing plate. The press cycle is as follows: 1) Layup of parts onto tray with pins in upright position 2)Press the button to drop the parts that does not touch the pins 3) Pulling of vinyl over finished bed 4) Loading of press 5) Processing parts through the press cycle 6) Unloading of press 7) Turn over device removes parts from tray 8) Tray returns for new cycle All of this is done with two rotating trays,the working period of ordinary workpiece is less than 2 minutes (results vary based on part configurations, and ambient conditions).
