1.Features:
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.
When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate
analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier. The exclusive DSP processes and calculates and then
outputs the measurement results on LCD.
* Multiple parameter measurement: Ra, Rz, Rq, Rt
* Highly sophisticated inductance sensor
* Four wave filtering methods : RC, PC-RC, GAUSS and D-P
* Built-in lithium ion rechargeable battery and control circuit with high capacity
* Small in size, light in weight and easy to use
* Can communicate with PC computer for statistics, printing and analyzing by the optional cable and the
software for RS232C interface.
*Manual or automatic shut down. The tester can be switched off by pressing the Power key at any time.
On the other hand, the tester will power itself off about 5 minutes after the last key operation.
*The tester can memorize 7 groups of measurement results and measuring conditions for later use or download to PC.
*Metric /Imperial Conversion
2.Specifications
Display 4 digits, 10 mm LCD, with blue backlight
Parameters: Ra, Rz, Rq, Rt
Measuring Range
Ra, Rq: 0.005-16.00um/0.020-629.9uinch
Rz,Rt: 0.020-160.0um/0.078-6299uinch
Accuracy: +10%
Fluctuation of display value: Not more than 6%
Sensor :
Test Principle: Inductance type
Radius of Probe Pin: 5um
Material of Probe Pin: Diamond
Dynamo-measurement of Probe: 4mN(0.4gf)
Probe Angle: 90p
Vertical Radius of Guiding Head: 48mm
Maximum driving stroke: 17.5mm/0.7inch
Cutoff length (l): 0.25mm / 0.8mm / 2.5mm optional
Evaluation length: 5l
Driving speed:
Sampling length = 0.25mm Vt=0.135mm/s
Sampling length = 0.8mm Vt=0.5mm/s
Sampling length = 2.5mm Vt=1mm/s
Returning Vt=1mm/s
Profile digital filter
Filtered Profile: RC
Filtered Profile: PC-RC
Filtered Profile: Gauss
Non-Filtered Profile: D-P
Resolution : .001m if reading ú+10m
0.01m if 10m_readingú+100m
0.1m if reading 100m
Evaluation length : 5 cut-off
Power Li-ion battery: rechargeable
Operating conditions: Temp. 0~50µ
Humidity <80%
Size140x57x48 mm (5.5x2.2x1.9 inch)
Weight: about 420 g.
Features
Used in production site to measure surface roughness of various machinery-processed parts, calculate corresponding parameters according to selected measuring conditions and clearly display all measurement parameters.
Specifications
Displayª 4 digits, 10 mm LCD, with blue backlight
Parameters: Ra, Rz
Display Range
Ra: 0.05-10.00um/1.000-400.0uinch
Rz: 0.020-100.0um/0.780-4000uinch
Accuracy: Not more than 10%
Fluctuation of display value: Not more than 6%
Sensor :
Test Principle: Inductance type
Radius of Probe Pin: 10um
Material of Probe Pin: Diamond
Measurement Force of Probe: 16mN(1.6gf)
Probe Angle: 90fp
Vertical Radius of Guiding Head: 48mm
Maximum driving stroke: 17.5mm/0.7inch
Cutoff length (l): 0.25mm / 0.8mm / 2.5mm optional
Evaluation length: 1~5 cut off optional
Driving speed:
sampling length = 0.25mm Vt=0.135mm/s
sampling length = 0.8mm Vt=0.5mm/s
sampling length = 2.5mm Vt=1mm/s
returning Vt=1mm/s
Resolution : 0.001¬ªm if reading ·+10¬ªm
0.01¬ªm if 10¬ªmf_reading·+100¬ªm
0.1¬ªm if reading fª100¬ªm
Power Li-ion battery: rechargeable
Operating conditions: Temp. 0-50f¦
Humidity <80%
Attachment:
Standard Sensor RP-100
Groove Stylus SRP-110
curvature Probe SRP-120
Extension Rod SER-150
Mesurement Stand SRS-1
Standard Sample Plate SSP-180
Cable and Software for RS-232/USB)
Bluetooth interface
Size·ª140x57x48 mm (5.5x2.2x1.9 inch)
Weight: about 420 g
Features
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameters.
When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate
Specifications
Display·ª 4 digits, 10 mm LCD, with blue backlight
Parameters: Ra, Rz, Rq, Rt
Measuring Range
Ra, Rq: 0.005-16.00um/0.020-629.9uinch
Rz,Rt: 0.020-160.0um/0.078-6299uinch
Accuracy: f_f+10%
Fluctuation of display value: Not more than 6%
Sensor :
Test Principle: Inductance type
Radius of Probe Pin: 5um
Material of Probe Pin: Diamond
Dynamo-measurement of Probe: 4mN(0.4gf)
Probe Angle: 90fp
Vertical Radius of Guiding Head: 48mm
Maximum driving stroke: 17.5mm/0.7inch
Cutoff length (l): 0.25mm / 0.8mm / 2.5mm optional
Evaluation length: 5l
Driving speed:
sampling length = 0.25mm Vt=0.135mm/s
sampling length = 0.8mm Vt=0.5mm/s
sampling length = 2.5mm Vt=1mm/s
returning Vt=1mm/s
Profile digital filter
Filtered Profile: RC
Filtered Profile: PC-RC
Filtered Profile: Gauss
Non-Filtered Profile: D-P
Resolution : .001¬ªm if reading ·+10¬ªm
0.01¬ªm if 10¬ªmf_reading·+100¬ªm
0.1¬ªm if reading fª100¬ªm
Evaluation length : 5 cut-off
Power Li-ion battery: rechargeable
Operating conditions: Temp. 0~50f¦
Humidity <80%
Attachment:
Standard Sensor RP-100
Groove Stylus SRP-110
curvature Probe SRP-120
Extension Rod SER-150
Mesurement Stand SRS-1
Standard Sample Plate SSP-180
Cable and Software for RS-232/USB)
Bluetooth interface
Size·ª140x57x48 mm (5.5x2.2x1.9 inch)
Weight: about 420 g
This instrument is compatible with four standards of site to measure surface roughness of various machinery-processed parts, calculate corresponding and clearly display all measurement parameter. When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of
Inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier. The exclusive dsp processes and calculates and then
Outputs the measurement results on lcd.
* multiple parameter measurement: ra, rz, rq, rt
* highly sophisticated inductance sensor
* four wave filtering methods : rc, pc-rc,
Gauss and d-p
* built-in lithium ion chargeable battery and control
Circuit with high capacity
* small in size, light in weight and easy to use
* can communicate with pc computer for statistics,
Print and analyz by the optional cable and the
Software for rs232c interface.
*manual or automatic shut down. The tester can be
Switched off by pressing the power key at any time.
On the other hand, the tester will power itself off
About 5 minutes after the last key operation.
To measure surface roughness of various machinery - processed parts
Mobile app compatible to get the higher accuracy, convenient to be used in a small space
Dual OLED displays to suit your applications;
2 start keys ( the left key & the right key) to satisfy the different using habits;
Mobile app compatible to get the higher accuracy, convenient to be used in a small space
ARM processor to offer higher speed, low power consumption and fast accurate measurement.
Light weight of 150gï¼? easy & convenient to use.
z
50003 Surface Roughness Tester Suppliers
Short on time? Let Surface Roughness Tester sellers contact you.
Model No.: PRSR110 Dimensions (mm): 110Ã?81Ã?32 Weight: 150g Warranty: 12 months
Standard Deliveryï¼?
Main Unit�Calibration Block�Power Adapter�USB Cable�Manual�Packing List
Features:
Dual OLED displays to suit your applications
2 start keys ( the left key & the right key) to satisfy the different using habits
Mobile app compatible to get the higher accuracy, convenient to be used in a small space
ARM processor to offer higher speed, low power consumption and fast accurate measurement
Light weight of 150gï¼? easy & convenient to use
Wide measuring range, for all metallic materials
Direct display of hardness scales hrb, hrc, hv, hb, hs, hl
Conversion to tensile strength (u.T.S.)
Test at any angle, even upside down
Removable printer included
Six impact devices are available for special applications
Large lcd display showing all functions and parameters
Battery low indication
New function of software calibration
Power charging indication on the keyboard led
Fault distinguish in details
Application:used for measuring thickness and corrosion of pressure vessels,chemical equipment,boilers,oil storage tanks,etc.in industries of petroleum,shipbuilding,power station,and machine manufacturing.
Model: CM8825FN
In built probe(s)
Operating principle: magnetic induction/eddy current (F/NF)
Measuring range:0-1250um/0-50mil
Resolution; 0.1/1
Accuracy: í+1-3%n or í+2.5um
Min. measuring area: 6mm
Min. sample thickness: 0.3mm
Battery indicator: low battery indicator
Metric/ imperial: convertible
Power supply: 4x1.5V AAA(UM-4)battery
Auto power off
Operating conditions:0-+45íµ(32¿H-104¿H),í_90%RH
Dimensions: 126x65x27mm
weight: 81g(not including battery)
Optional accessories: other range 0-200um to 15000um
RS-232C cable & software:
1.USB adaptor for RS-232C
2.Bluetooth interface.
- Wrist type hardness tester,
- Easy to read menu with back light
- Large LCD display with back light
- For most metals
- Based on the hardness HL value, convers to HRB, HRC, HV, HB, HS and Tensile strength.
- Impact devices D\DC\DL\C\D+15 and G are available for special applications
- Test at any angle, even upside down
- RS 232 output and internal memory in a bath of 1250 average readings
- Date and time display.
- Lower and upper limits setting with low-high display judge
- High accuracy +/- 0.5%
- Works on standard AAA batteries.
- Auto shutdown after two minutes.
- Conforming to ASTM A 956
The standard delivery are:
Main unit
Small supporting ring
Impact device D
Two AAA batteries
Test block with HLD-value
Software and cable
Carrying case
Operation manual
Cleaning brush
Leather wrist strap
Certificates.
Mill scale, is formed on the outer surfaces of plates, sheets or profiles when they are being produced by rolling hot iron or steel billets in rolling or steel mills.
It looks like a hard brittle sand and is mainly composed of iron oxides, mostly ferric, and is bluish black in color.
Being produced during the reheating, conditioning and hot rolling operation for the production of steel articles, the mill scale initially adheres to the steel surface and protects it from atmospheric corrosion, provided no break occurs in this coating.
From the chemical and physical analysis performed on the scrap, and according to the european environmental rules, the material has been classified as a special non dangerous waste, listed in green list
In particular the mill scale can be classified as follows:
Einecs (european commission no.): 266-007-8
Waste code: 10 02 10
Basel code: b 12 30
Hs code: 2619.00
50003 Surface Roughness Tester Suppliers
Short on time? Let Surface Roughness Tester sellers contact you.
