YL-SNF-C(Na2SO4 less than 18%) Sodium Naphthalene Sulfonate Formaldehyde This product, named -naphthalene sulfonate formaldehyde condensate, is non-air entraining superplasticizer. It has good dispersing performance to the cement particles. Compared with traditional plasticizer, it has higher water reducing rate, and good for preparing mass concrete, fresh concrete required for early strength and high strength, and precast concrete and parts. It also has good adaptability to commonly used cement, and widely used in roads, bridges, dams, power engineering, civil construction, steam and natural curing precast parts and other projects. Advantage: * Higher water reducing rate. By the recommended dosage, the water reducingrate can reach 15% -20%. * Improve the workability of concrete, such as compression, long-term strength, flowability, etc., and enhance the reinforcement of steel and concrete. * Reduce costs. In the case of maintaining the same workability and strength, cement amountcan be reduced. * Wide adaptability, cost-effective. Good adaptability to all kinds of cement, such as Portland cement, slag cement, volcanic ash cement, etc. * Be mother material to formulate other admixtures.(like early strength, set retarder, pumping agent, antifreezing agent).
Items Standards Appearance Yellow beige powder Identification Meet the requirements Solid content , % 92% min Sodium sulphate , % 10.0max Water content, % 8.0max Ph value 7.0-9.0 Bulk density, g/cm3 0.5-0.8 Impurity 0.05% max Calcium & magnesium 0.4% max. 25kg 40kg 1000kg per bag.
Product Description High Range Water-Reducing Admixture Sodium Naphthalene Sulphonate Formaldehyde, Poly Naphthalene Sulfonate Formaldehyde Condensate,Concrete Admixture Uses Sodium Naphthalene Sulphonate Formaldehyde produces concrete with extremely workable characteristics referred to as high slump. PNS also allows concrete to be produced with very low water/cement ratios at low or normal slumps. Sodium Naphthalene Sulphonate Formaldehyde is ideal for use in prestress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation Sodium Naphthalene Sulphonate Formaldehyde Specification: Solid Content :93% PH value :8.42 Chlorides Content :0. 39% Sodium Sulfate Content :16% Addition Rates Sodium Naphthalene Sulphonate Formaldehyde can be added directly or added in after melt. It can be added during mixing and after-mixing. The afterward approach can achieve better result. The suggested addition rate is 0.75%. Sodium Naphthalene Sulphonate Formaldehyde Direction Prepare solutions as required. Direct use of powdery agent is allowed. Alternatively the addition of the agent is followed by water moisturization (water-cement ratio: 60%). The agent can be combined with other externally applied agents if pilot development or laboratory experiment succeeds. Sodium Naphthalene Sulphonate Formaldehyde Package, Storage & Handling For powder: Woven fabric bag with plastic liner. Net weight: 25kg +/- 0.1 kg. 25kg in PP woven bag lined with plastic film
Product Description High Range Water-Reducing Admixture Sodium Naphthalene Sulphonate Formaldehyde, Poly Naphthalene Sulfonate Formaldehyde Condensate,Concrete Admixture Uses Sodium Naphthalene Sulphonate Formaldehyde produces concrete with extremely workable characteristics referred to as high slump. PNS also allows concrete to be produced with very low water/cement ratios at low or normal slumps. Sodium Naphthalene Sulphonate Formaldehyde is ideal for use in prestress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation Sodium Naphthalene Sulphonate Formaldehyde Specification: Solid Content :96.42% PH value :8.3 Chlorides Content :0.25% Sodium Sulfate Content :4.4% Addition Rates Sodium Naphthalene Sulphonate Formaldehyde can be added directly or added in after melt. It can be added during mixing and after-mixing. The afterward approach can achieve better result. The suggested addition rate is 0.75%. Sodium Naphthalene Sulphonate Formaldehyde Direction Prepare solutions as required. Direct use of powdery agent is allowed. Alternatively the addition of the agent is followed by water moisturization (water-cement ratio: 60%). The agent can be combined with other externally applied agents if pilot development or laboratory experiment succeeds. Sodium Naphthalene Sulphonate Formaldehyde Package, Storage & Handling For powder: Woven fabric bag with plastic liner. Net weight: 25kg +/- 0.1 kg. 25kg in PP woven bag lined with plastic film
The raw material naphthalene superplasticizer (SNF/FDN/PNS) has strong dispersion effect on cement particles and good use effect of preparing super flowing concrete as well as cast-in-situ concrete and precast members with early strength and high strength requirements, can comprehensively improve various properties of the concrete, and is widely applied to highways, bridges, dams, harbors, tunnels, electric power, water conservancy as well as industrial and civil architecture, steam-cured and naturally-cured precast members and so on. Specifications Model SNF-A appearance Light brown powder Solid content â?¥93% PH value 7-9 Sodium sulfate ï¼?5% Chloride ion ï¼?0.3% Water reduction 22%-25% Cement paste fluidity â?¥250mm Water Insolubles â?¤2% Air content â?¤2% Application 1. Construction: 1. Widely used in precast & ready-mixed concrete, armored concrete and pre-stressed reinforced concrete in key construction projects such as dam and port construction, road building & town planning projects and dwelling erections etc. 2. Suitable for preparation of early-strength, high-strength, high-anti-filtration and self sealing&pumpable concrete. 3. Used for and widely for self-cured, vapor-cured concrete and its formulations. At the early stage of application, extremely prominent effects are shown. As the result, the modulus and site utilization can be drastically, the procedure of vapor cure is omitted in peak heat summer days. Statistically 40-60 metric tons of coal will be preserved when a metric ton of the material is consumed. 4. Compatible with Portland cement, normal Portland cement, Portland slag cement, flyash cement and Portland pozzolanic cement etc. Others: Because of the high dispersion force and low foaming characteristics, SNF has also been widely used in other industries as Anionic Dispersing Agent. Dispersing agent for disperse, vat, reactive and acid dyes, textile dying, wettable pesticide,paper,electroplating, rubber, water-soluble paint, pigments,oil drilling, water treatment,carbon black, etc.
Sodium Naphthalene Sulphonate BASIC INFORMATION: [Chemical name] sodium naphthalene sulphonate [Cas No.] 9084-06-4 [Molecular formula] SNF [Molecular weight] --- [standard] GB/T8077-2012 [Packing] 25kgs,1000kg,1200kg,1250kg PP bags with PE liner Naphthalene formaldehyde sulphonate water reducing agent is a synthetic powder based onbeta-sulphonate formaldehyde ondensate and reactive polymer. It has the properties of high range water reduction, set retarding and excellent strengthening. Elt-nsf sodium sulfate is less than 10% , suitable to middle strength or high strength concrete where high range water reduction is desired. Application: A. Used for and widely for self-cured, vapor-cured concrete and its formulations. At the early stage of application, extremely prominent effects are shown. As the result, the modulus and site utilization can be drastically, the procedure of vapor cure is omitted in peak-heat summer days. Statistically 40-60 metric tons of coal will be preserved when a metric ton of the material is consumed. B.Suitable for preparation of early-strength, high-strength, high-anti-filtration and self-sealing& pumpable concrete. C.Widely used in pre-cast & ready-mixed concrete, armored concrete and pre-stressed reinforced concrete in key construction projects such as dam and port construction, road building & town planning projects and dwelling erections etc. D.Compatible with Portland cement, normal Portland cement, Portland slag cement, fly-ash cement and Portland pozzolanic cement etc.
Sodium naphthalene sulphonate fdn- 1 used for and widely for self-cured, vaporcured concrete and its formulations. At the early stage of Application, extremely prominent effects are shown. As the result, the modulus and siteutilization Can be drastically, the procedure of vapor cureis omitted in peak-heat summer days. Statistically 40-60 metric tons of coal willbe preserved when a metric ton of the material is consumed. 2 suitable for preparation of early-strength, high-strength, high-anti-filtration and selfsealing& pumpable concrete.
It is the condensation compound of formaldehyde and naphthalene sulfonic acid; is a good non-air bleed high efficiency water reducing agent. It can be used in the prestressed unit and concrete engineering of highway, port and high-rise. We also could supply the other type water reducer such as poly-carboxylate superplasticizer, sulfonated melamine-formaldehyde resin superplasticizer. 25kg bag
Product Description High Range Water-Reducing Admixture Sodium Naphthalene Sulphonate Formaldehyde, Poly Naphthalene Sulfonate Formaldehyde Condensate,Concrete Admixture Uses Sodium Naphthalene Sulphonate Formaldehyde produces concrete with extremely workable characteristics referred to as high slump. PNS also allows concrete to be produced with very low water/cement ratios at low or normal slumps. Sodium Naphthalene Sulphonate Formaldehyde is ideal for use in prestress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation Sodium Naphthalene Sulphonate Formaldehyde Specification: Solid Content :96.42% PH value :8.3 Chlorides Content :0.25% Sodium Sulfate Content :4.4%. For powder: woven fabric bag with plastic liner. Net weight: 25kg +/- 0.1 kg.
Product Description: High Range Water-Reducing Admixture Sodium Naphthalene Sulphonate Formaldehyde, Poly Naphthalene Sulfonate Formaldehyde Condensate,Concrete Admixture Uses: Sodium Naphthalene Sulphonate Formaldehyde produces concrete with extremely workable characteristics referred to as high slump. PNS also allows concrete to be produced with very low water/cement ratios at low or normal slumps. Sodium Naphthalene Sulphonate Formaldehyde is ideal for use in prestress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation Sodium Naphthalene Sulphonate Formaldehyde Specification: Solid Content :96.42% PH value :8.3 Chlorides Content :0.25% Sodium Sulfate Content :4.4% Addition Rates: Sodium Naphthalene Sulphonate Formaldehyde can be added directly or added in after melt. It can be added during mixing and after-mixing. The afterward approach can achieve better result. The suggested addition rate is 0.75%. Sodium Naphthalene Sulphonate Formaldehyde Direction Prepare solutions as required. Direct use of powdery agent is allowed. Alternatively the addition of the agent is followed by water moisturization (water-cement ratio: 60%). The agent can be combined with other externally applied agents if pilot development or laboratory experiment succeeds. Sodium Naphthalene Sulphonate Formaldehyde Package, Storage & Handling. For powder: Woven fabric bag with plastic liner. Net weight: 25kg +/- 0.1 kg.
Sodium naphthalene formaldehyde is high range water-reducing and an anion surface active agent based on polyalkyaryl- sulphonate. Technical spefication: Solid content 92% min Moisture 8.0 % max Fineness 5.0% max Ph value 7 - 9 Chlorides content 2.0% max Surface tension 68-72 mn/m Cement flowing rate 230mm min Concrete reducing water rate 18% min Sodium sulfate content 18% max (5%max is also available) Sodium naphthalene formaldehyde produces concrete with extremely workable characteristics referred to as high slump. Pns also allows concrete to be produced with very low water/cement ratios at low or normal slumps.Sodium naphthalene formaldehyde is ideal for use in prestress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation. Addition ratessodium naphthalene formaldehyde can be added directly or added in after melt. It can be added during mixing and after-mixing. The afterward approach can achieve better result. The suggested addition rate is 0.75%.Sodium naphthalene formaldehyde directionprepare solutions as required.Direct use of powdery agent is allowed. Alternatively the addition of the agent is followed by water moisturization (water-cement ratio: 60%).The agent can be combined with other externally applied agents if pilot development or laboratory experiment succeeds. Packed in plastic film bag wrapped with plastic woven sack with a net weight of 25kg each.
BASIC INFORMATION: [Chemical name] Sodium Naphthalene Sulphonate [Cas No.] 1321-69-3 [Molecular formula] C10H8O3SNa APPLICATION: A. Used for and widely for self-cured, vapor-cured concrete and its formulations. At the early stage of application, extremely prominent effects are shown. As the result, the modulus and site utilization can be drastically, the procedure of vapor cure is omitted in peak-heat summer days. Statistically 40-60 metric tons of coal will be preserved when a metric ton of the material is consumed. B.Suitable for preparation of early-strength, high-strength, high-anti-filtration and self-sealing& pumpable concrete. C.Widely used in pre-cast & ready-mixed concrete, armored concrete and pre-stressed reinforced concrete in key construction projects such as dam and port construction, road building & town planning projects and dwelling erections etc. D.Compatible with Portland cement, normal Portland cement, Portland slag cement, fly-ash cement and Portland pozzolanic cement etc.
Description YL-NNO is light brown yellow powder, an anion surface active agent. Easily soluble in water, acid, alkali and hard water. It has good dispersing property and affinity with protein and polyamide. Usage Mainly used for vat dye dyeing, reactive dye dyeing and acid dye dyeing. It can work as dispersant for acid staining pad and pigment pad dyeing; auxiliary for reducing dye powder and slurry. It can also be used in leveling agent in dyeing industry Advantages 1). As dispersant NNO;in disperse dye, vat dye, reactive dye, acid dye and leather dye. It has good grinding effect, hydrotropy and dispersibility. 2). As dispersant in textile printing and dyeing industry: pigment pad dyeing of disperse dye;vat acid dyeing of disperse dye; dye for silk and feather mixture; soluble vat dye dyeing; Etc. also can be used as dispersant for disperse dye and lake making; filler for commercial dye etc. 3). As dispersant in wettable pesticide and herbicide, the dispersibility and solubility of pesticide can be improved. 4). As dispersant in electroplating industry, so that the cladding film can be equal and have a better brightness. 5). As auxiliary tanning agent in leather industry, used together with tanning agent (ratio 1:10) to avoid tanning agent stickwith leather. Can also help to disperse dye to get a better appearance in color. 6). As dispersant for paper industry. After adding NNO into wood pulp to avoid the stain from the condensation ofasphaltum, resin and other material 0.2%-0.5% of the wood pulp weight as dosage is preferable. Can work as precipitator for animal size, 20%-30% of the size weight as dosage is preferable. 7). As dispersant in rubber industry. Can disperse sulfur, accelerant, anti-aging agent and some filler(like zinc oxide, barium sulphate, calcium carbonate etc). 2%-4% of the dry powdeweight as dosage is preferable. Can make NNO into 10% solution, then grind with others in ball grinder. 8). Also can be used in coating, painting, pigment, carbon black etc. 9). Can be used in color lake industry. Specification Item Specification Dispersing rate % 95%min Sodium sulfate content % 5 max pH value 7-9 Insolubles % 0.05% max Content of calcium and magnesium ion, ppm 2000 Package, Storage & Shelf Life For powder: Woven plastic bag with film liner. Net weight: 25kg +/- 0.2 kg. It should be stored in a dedicated warehouse that is well-ventilated and dry and keep away from moisture. Shelf Life: Minimum 12 months. After the expiration date, it can be used if testing results is qualified. For powder: Woven plastic bag with film liner. Net weight: 25kg +/- 0.2 kg
The raw material naphthalene superplasticizer (snf/fdn/pns) has strong dispersion effect on cement particles and good use effect of preparing super flowing concrete as well as cast-in-situ concrete and precast members with early strength and high strength requirements, can comprehensively improve various properties of the concrete, and is widely applied to highways, bridges, dams, harbors, tunnels, electric power, water conservancy as well as industrial and civil architecture, steam-cured and naturally-cured precast members and so on.
Product Name:Naphthalene based superplasticizer/Sodium Naphthalene sulfonate/sodium naphthalene sulfonate formaldehyde condensation/sulfonated naphthalene formaldehyde/sodium naphthalene sulfuric acid formaldehyde CAS No.: 9084-06-4 HS No.:382440100 Chemical Formula:(C11H7O4SNa)n Payment:T/T Delivery:Within 15 days after payment. Raw materials:crude naphthalene,concentrated sulfuric acid,formaldehyde,liquid alkali Specification: Appearance yellow powderyellow powder yellow powder Solid content 92% min 92% min 92% min Sodium sulfate content 5% max 10% max 18% max Chloride content 0.3% max0.4% max 0.5% max PH 7~97~9 7~9 Fluidity of cement paste 250 mm min 240 mm min 230 mm min Package and Storage: Package:25 kg plastic bags with PP liner,Alternative package may be available upon request. Storage:Shelf-life time is 2 years if kept in cool,dried place.Test should be done after expiration.
Application 1. Widely used in precast & ready-mixed concrete, armored concrete and pre-stressed reinforced concrete in key construction projects such as dam and port construction, road building & town planning projects and dwelling erections etc. 2. Suitable for preparation of early-strength, high-strength, high-anti-filtration and selfsealing&pumpable concrete. 3. Used for and widely for self-cured, vapor-cured concrete and its formulations. At the early stage of application, extremely prominent effects are shown. As the result, the modulus and site utilization can be drastically, the procedure of vapor cure is omitted in peakheat summer days. Statistically 40-60 metric tons of coal will be preserved when a metric ton of the material is consumed. 4. Compatible with Portland cement, normal Portland cement, Portland slag cement, flyash cement and Portland pozzolanic cement etc. Package & Shipping Packing: 25kg/bag, outer woven bags with inner plastic lining. Storage: Kept in dry and ventilating place, prevent from rain and moisture when storage if agglomerated, please crush and make it into solution, and its effect will be the same. Transportation: Non-toxic, harmless, non-inflammable and non-explosive chemicals it can be transported in truck and train. Why choose us About Us Shandong Jufu Chemical Technology Co., Ltd. is a professional company has been focused on research, production, and sales of various of chemical products since establishment. Began with concrete admixtures, our main products include: Sodium Lignosulfonate, Calcium Lignosulfonate, Sodium Naphthalene sulfonate formaldehyde, polycarboxylate Superplasticizer and sodium gluconate concrete, which has been widely used as concrete water reducers, plasticizers and retarders. Our Service 1. SGS certified Chinese supplier 2. Provide product search, offer, quality control, warehousing, international logistics, etc one-stop service; 3. Offer customization product and all-around product application programs according to customers' requirement; 4. Supply FREE sample and accept small orders; 5. Accept Customized Packages; 6. Operated by in professional teams, offer quality after-sales service and technical support.
Sodium naphthalene sulphonate formaldehyde is widely applicable for cements builing, especially for the following: fluid cement, plasticized cement, steamed cement, water-tight cement, water-proof cement, prefabricated cement, prestressed reinforced cement and high strength cement. But the adaptability to different kind of cement is different.
Appearance Light Brown or Dark Brown Powder. Solid Content 87~88~90~91~92~93~94~95 PH Value 7-9 Sodium Sulfate Content
Sodium Naphthalene Formaldehyde (SNF-Superplasticizer for Concrete) CAS Code: 36290-04-7 SNF a high range water reducer, commonly referred to as a super plasticizer, also named Naphthalene Sulphonate Formaldehyde Condensate (short name: SNF, PNS, NSF, etcâ?¦) SNF is made from naphthalene, sulfuric acid, formaldehyde and liquid alkali, through sulfonation, hydrolyzation, condensation and neutralization reaction and then drying to powder. SNF-A5% contains very small chloride. Thus, it meets the requirements of chemical admixture specifications for concrete: ASTM Designation C 494 as a Type F admixture, GB8076-2008 and GB50119-2003. Usage SNF produces concrete with extremely workable characteristics referred to as high slump. SNF also allows concrete to be produced with very low water/cement ratios at low or normal slumps. SNF is ideal for use in pre stress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation. SNF will also fluidize concrete, making it ideal for tremie concreting or other applications where high slumps are desired. SNF is compatible with Portland Cement, Normal Portland cement, Portland Slag Cement, Fly-ash Cement, Portland Pozzolanic Cement, etc.
Description YL-SNF-A is a high range water reducer, high concentration naphthalene-based superplasticizer, also named Naphthalene Sulfonate Formaldehyde Condensate (NSF), SNF, PNS and FDN etc. YL-SNF-A (Na2SO4 less 5%) contains no chloride, non-corrosive to steel bars, non-poisonous, odorless, and non-flammable. Thus, it meets the requirements of chemical admixture specifications for concrete, complying with ASTM C 494, Type F. ASTM C 1017, GB8076-2008 and GB50119-2003 etc. Uses 1.YL-SNF-A possesses the features of no retarding, no air-introducing, superplastic high water-reducing and strength enhancing. It has no chloride, low alkali content, low sulphonate, and high purity. It can be widely used in different concretes with less dosage and easy to use. 2.YL-SNF-A can be applied to make flowing, strong or steam-curing concrete. The minimum working temperature can be as low as zero centigrade degree. In steam curing, concrete with superplasticizer has to be strong enough before heating. The steam curing specification has to be pre-tested. It is particularly used as base material for compound admixtures. 3.It can prevent from the alkali-aggregate reaction because of the biggish alkali reactivity of aggregate or the alkali-aggregate reaction in the moist environment. Advantage 1.High water-reducing rate: YL-SNF-A can reduce water 20-30%. It has features of superplasticizer, effectively increases concrete fluidity and reduces water penetration and segregation and improves the encapsulation force of the concrete with reinforcing steel bar. 2.Strengthening: Given the same amount of cement and slump requirement, this product with the dosage 0.5-1.2% can increase the concrete early strength and reinforced effect by 50-100%, 40-70%, 25-60% and 20-60% on day 1, 3, 7, and 28 respectively. 3.High applicability: It can be used with different variety of cement. It is compatible with other admixtures. 4.Low sodium Sulfate content: The aqueous solution has no crystals in winter, which can avoid pipeline congestions when JK-01 NP applied. It is suitable for automatic working. 5.Effective durability: It can modify the structure of concrete and increase the property of anti-seepage, anti-freezing, and carbonization. 6.Easy to use: It can be added directly or used after dissolved in water. It can be used for different working condition and concrete mixer. Specifications Items Criteria Actual results(C¡¨¢0.75%) Appearance -- Brown powder Solid Content % 92 min 92.65 Moisture % 8.0 max 7.35 Fineness (0.315mm remains) % 15.0 max 9.2 PH value 7 - 9 8.5 Sodium Sulfate Content % 5.0 max 3.8 Chloride Content % 1.0 max 0.11 Surface Tension 68-72 Mn/m 71 Cement Flowing Rate 240mm 265mm Water Reducing Rate 20% min 22.3% Steel-bar Corrosion None None Dosage 0.5-1.2% by weight of cement. Exact dosage rates depend on the type of effect sought, quality of cement and aggregates, water/cement ratio and ambient temperature. Therefore, in many cases it is advisable to carry out trial mixes. YL-SNF-A can be added directly or added in after dissolved in water. It can be added during mixing and after-mixing (better). The after-mixing approach can achieve better result. Test Data Sheet Items Dosage rate (Cx%) Water (g) Slump (mm) Water reducing rate (%) Compressive strength (MPa) /Compressive strength rate (%) 1 day 3 days 7 days 28 days Reference concrete 0 2555 82 0 4.34/100 13.70/100 20.19/100 24.06/100 YL-SNF-A 0.75 1986 89 22.3 7.63/173.3 23.85/173.4 30.84/150.7 33.72/137.2 Package, Storage & Shelf Life For powder: Woven plastic bag with film liner. Net weight: 25kg +/- 0.2 kg. It should be stored in a dedicated warehouse that is well-ventilated and dry and keep away from moisture. Shelf Life: Minimum 12 months. After the expiration date, it can be used if testing results is qualified. For powder: Woven plastic bag with film liner. Net weight: 25kg +/- 0.2 kg.
