Media converter Parameter Specifications Access mode 10/100mbps Standard Ieee802.3 10base-t ethernet, ieee802.3u, 100base-tx/fx fast ethernet, ieee802.3x flow control, ieee802.1q vlan, ieee802.1p qos, ieee802.1d spanning tree Wavelength 850nm/1310nm/1550nm Transmission distance Single-fiber single-mode: 25/40/60/80/100km ; category-5 twisted pair: 100m Port One rj45 connector, connected to stp/utp category-5 twisted pair one fiber port: multi-mode - sc or st (fiber size: 50, 62.5/125µm) single mode - sc/fc fiber port (fiber size: 9/125µm) single-fiber single-mode - sc/fc fiber port (fiber size: 9/125µm) Conversion mode Medium conversion, storing and forwarding Mac address table I k Buffer space 1mbit Flow control Full duplex state: flow control; half duplex state: back pressure mode Delay 9.6us Bit error rate
Media converter Two 10/100m electrical ports, one single-mode or multi-mode optical port Multi-mode transmission distance: 2km, single-mode transmission distance: 120km, single-strand double-directions /double-strand double-directions. Set - in 1m cache, supporting 2k mac address self-learning and self-updating capability Supports forcible execution the cross of 10m, 100m, full-duplex, half-duplex, twisted-pair and automatically adapt to connect auto mdix function directly Supports rate control function and the rate can been controlled between nx64k (n=1~1600) to 100mbps Supports renovate system automatically function, support system regular refresh automatically via setting time, protect from system halted Supports management based on web, snmp, telnet or local console Supports lld(search disconnected link automatically), llr(return alarm message when disconnected link found) Supports llcf(report the disconnected alarm message to local network administration) Detect and control the operational states of electrical port and optical port of the near end and the far end via interface of management Supports open or close electrical and optical ports through via the far end network management Supports legal maximum packet size up to 1912 bytes, support cisco, isl and vtp Physical property: Input power: ac 100v~220v or dc 48v Dimension: 191mm x 110mm x 25mm Environment requirements: Operating temperature: 0¦-50¦ Storage temperature: -40¦-70¦ Environment humidity: 5-90%(non-condensing) Export carton with inner box
10gbps media converter, 90 to 240v ac, 12v dc adapter power source type Specifications: Interface: Left side: One 10gbps rj-45 port One 10gbps sfp + port (mini-gbic) Right side: One rs-232 console port (rj-45 connector) One power jack Wire speed cable length: up to 100m cat6a cable for wire speed transmission Transceiver (phy), teranetics chip for 10gbase-t and net logic chip for 10gbase-r Temperature:
Main features In conformity to IEEE 802.3 10 Base-T standard. In conformity to IEEE 802.3u 1000 Base-TX, IEEE802.3z, IEEE802.3abstandard Built in high efficiency SRAM for packet buffer, with 1K-entry lookup table and 4-way associative hash algorithm Half duplex: back pressure flow control Full duplex: IEEE802.3x flow control Automatic identification of MDI/MDI-X cross line Technical parameter: Standard protocol: IEEE802.3 10 Base-T standard, IEEE 802.3u 1000Base-TX and IEEE802.3z standard Connector: one UTPRJ-45 connector, one SC/ST connector Operation mode: full duplex mode or half duplex mode Power supply parameter: Adapter(External): 110-265V AC input, 5V1A DC output Power(Internal): 110-265V AC input, 5V1A DC output Environmental temperature: 0 - 50 Relative humidity: 5%-90% TP cable: Cat5 UTP cable Transfer fiber: multi-mode: 50/125, 62.5/125 or 100/140ª¦m single mode: 8.3/125, 8.7/125, 9/125 or 10/125 Dimensions: Power external: 94mm(L)x 71mm(W) x 26mm(H) Power internal: 150mm(L) x 110mm(W)x 28mm(H)
Technical parameter 1. According with ieee802.3ab/z, ieee802.3u, ieee802.3x, ieee802.1q, 10base- t, 100b ase-tx, 1000base-tx, 1000base-sx, 1000base-lx standard. 2. Support tcp/ip, pppoe, dhcp, icmp, nat protocol. 3. Flow control: full-duplex adopt ieee802.3x, half-duplex adopt backpressure standard. 4. Eletricity port support auto-negotiation function, autoconditioning transmit mode and transmit speed. 5. Port support auto-mdi/mdix automatic reverse. 6. Support storage transmit mode, cache capability is 256k. 7. Support electricity port 1000m mode and self-adapt mode's switch. 8. Afford the state indicator, external power(output 5v~50hz 1a). 9. Interface: electric port: rj-45 fiber port: sc 10. Twisted-pair: cat. 5 cat. 6 11. Singlemode fiber: 8/125, 8.3/125, 9/125um 12. Working temperature: 0 ~ 50degree 13. Storage temperature: -20 ~ 70degree 14. Humidity: 5% ~ 90%(noncondensing) 15. Size: 118mm*86mm*27mm(l*w*h) Specification Connect type: sc/fc/st Fiber type: singlemode Wavelength: 1310nm Typical distance: 40km Min tx pwr: -6.0dbm Max tx pwr: 0.0dbm Sensitivity: < -24dbm Link budget: 18.0dbm 0.5kg/pcs
Media Converter, 10/100M 1310nm SM 5km Fiber optic media converter Skype:wirenettehnology Features : Surporting : Full duplex and half duplex transmission and capable of automatic negotiation. efficient builtin switching core ,to implement flow control and reduce broadcast packets. Surporting : The transmission of extra-long packes over VLAN Surporting : The selection of mutiple types of fiber ports such as dual-fiber multi-mode .dual-fiber single mode and single fiber single mode, to satisty the extended requirements of users. Technical specifications Parameter Specifications Access mode 10/100Mbps Standard IEEE802.3 10Base-T Ethernet,IEEE802.3u,100Base-TX/FX Fast Ethernet, IEEE802.3x Flow control,IEEE802.1q VLAN,IEEE802.1p QoS,IEEE802.1d Spanning Tree Wavelength 850nm/1310nm/1550nm Transmission distance Dual-fiber multi-mode: 2Km; dual-fiber single-mode: 25/40/60/80/100/120Km; single-fiber single-mode: 25/40/60/80/100Km Category-5 twisted pair: 100m Port One RJ45 connector, connected to STP/UTP category-5 twisted pair One fiber port: Multi-mode - SC or ST (fiber size: 50,62.5/125¦m) Single mode - SC/FC fiber port (fiber size: 9/125¦m) Single-fiber single-mode - SC/FC fiber port (fiber size: 9/125¦m) Conversion mode Medium conversion, storing and forwarding MAC address table I K Buffer space 1Mbit Flow control Full duplex state: flow control; half duplex state: back pressure mode Delay 9.6us Bit error rate
Fiber optic media converter 10M/100M media converters and 1000M media converters Products capability: According with the protocals: IEEE 802.3 IEEE 802.3u Fast Ethernet and IEEE802.3ab Support long data packet Easily for setting and debugging Technology specification: Wavelength:1310nm and 1550nm LAN port speed:10M/100M and 1000M Transimission distance:20km 40km 60km 80km 120km
Support 10/100m remote manageable fx media converters, 10/100/1000m remote manageable fx media converters, 1 fx + 2 RJ45 ethernet media converter, 125m~4.25g oeo, and 10g oeo managed at the same time Cover all functions of common fiber media converters, what's more, it supports protocols like snmp, web, telnet and console They can realize the integrated management to all chassis. Media converter card supports protocols like q-in-q double tag vlan, ieee802.1q tag vlan and ieee802.3x flow control Interface for management: rs232 console port (RJ45) and 10/100mbps RJ-45 ethernet port. Supporting remote and local management. With centralized management and top tree, several chassis can be managed in the same interface at the same time; with grouping management any converter can be conveniently manipulated among many converters. Standard package
Built-in ip-based web interface. Supporting remote and local management. Store and forward mechanism, supporling ieeee 802.3x frame flow control for full-duplex mode Manual ip address setting/dhcp client for ip address assignment. Event trap and snmp trap support. Password setting, ip setting and devices description setting through planet smart discovery utility Choice of fiber-connector from sc, lc, wdm, multi-mode / single-mode fiber /1000base-sx / lx mini gbic module. Standard package per customer
10gbps fiber to copper media converter for long distance transmission Network management function web snmp console Support dmi function for sfp+ fiber module Support itut prescribed dwdm/cwdm wavelength Media converter for network backbone(san, lan, man) Support 2u rack (16 channel) and standalone use Support jumbo frame Sfp+ fiber module detection, utp cable length detection Support hot plugging Type: rj45 to/from sfp+. Standard package per customer
Stand alone Managed 10/100/1000Base-Tx to 10/100/1000Base-Fx Media Converter SUN Telecoms stand alone Ethernet Media Converter is offers a cost-effective product to transmit distances up to 120km (Single-mode fiber). It makes it easy to incorporate the advantages of fiber-based connection technology in a managed Ethernet/Fast Ethernet network. Integrated Auto Cross-over MDI/MDI-X and NWay capabilities make it simple to deploy within a network. Also, the í¦hot-swappableí¦ design is ideal for scaling the system up or down quickly. Features: Web, SNMP, Console management Hot-swappable module Available with ST, SC, or WDM Simplex SC single-fiber connectors Auto MDI/MDI-X on copper port Auto-negotiation on copper port LED status for Link/Activity, LFS, 100, Loopback, and Full Duplex/Collision Link-Fault Signaling illuminates to indicate link failure Link-Fault Signaling function can boot up redundant link if network is installed with primary and redundant link Local and remote loopback
Product name: 10/100m fiber media converter Dual fiber Product intro: The fiber media converter transform the transmission media of ethernet signal from cat5 to optical fiber. It can extend the transmission distance to several kilometer or hundred kilometer.Using media converter is a economical solution to achieve long distance transmission base on current status.The media converter transform the transmission media of ethernet signal from cat5 to optical fiber. It can extend the transmission distance to several kilometer or hundred kilometer.Using media converter is a economical solution to achieve long distance transmission base on current status. Main features: Support ieee802.3u 10/100base-tx/fx ieee802.3x protocol. With the function of automatic recovery to prevent system halt. Indicate the working status. Avoiding the interference of electromagnetic wave, radio frequency and terrestrial current. Optional inside and outside power supply. No adjust electrical and optical environment. Led indicator light shows the working performance status. Duplex mode: Fiber media converter supports full duplex and semi duplex modes, 10/100mbps automatic protocol. Inserting to 14 slots rack with play and plug. Led status indicator light makes easy diagnosing network and checking troubleshooting. Good flow control and reset fuction prevent system halt. Transmission distance: Mm(multi mode): within 2 km Sm(single mode):20km, 40km, 60km, 80km, .100km Environment parameters: Working temperature: 0íµí½65íµ Storage temperature: -40íµí½+85íµ Humidity: 5%í½90% Other parameters: Inside power supply dimesion: 160mm*110mm*30mm Outside power supply dimesion: 110mm*70mm*30mm Rated voltage: ac220v/50hz Inside power supply: ac 220v/1a Inside power supply: dc 5v/1a
10/100/1000M Media converter 1550nm SM SC 40KM with external power supply Features: Supporting : Full duplex and half duplex transmission and capable of automatic negotiation. efficient built-in switching core ,to implement flow control and reduce broadcast packets. Supporting : The transmission of extra-long packets over VLAN. Supporting : The selection of multiple types of fiber ports such as dual-fiber multi-mode. dual-fiber single mode and single fiber single mode, to satisfy the extended requirements of users. Parameter: Parameters Specifications Access mode 10/100/1000Mbps Gigabit Ethernet Standard IEEE802.3 10Base-T Ethernet,IEEE802.3u 100Base-TX/FX Fast Ethernet, IEEE802.3ab 1000Base-T , IEEE802.3z 1000Base-SX/LX Gigabit thernet,IEEE802.1qVLAN,IEEE802.1p QoS,IEEE802.1d Spanning Tree Wavelength 850nm/1310nm/1550nm Transmission distance Dual-fiber multi-mode: 220m (fiber size: 62.5/125¦m)/550m(fiber size: 50/125¦m) Dual-fiber single-mode: 10/20/40/60/80/100/120Km Single-fiber single-mode: 10/20/40/60/80Km Category-5 twisted pairs: 100m Port One RJ45 port: Connected to STP/UTP category-5 twisted pairs One fiber port: dual-fiber multi-mode SC (fiber size: 50,62.5/125¦m) Dual-fiber single-mode SC/FC fiber port (fiber size: 9/125¦m) Single-fiber single-mode SC/FC fiber port (fiber size: 9/125¦m) Conversion mode Medium conversion Delay
TRX E1-10/100Base-T developed by Hengguang Technologies, employs the clarity E1 transmission channel in accordance with ITU-T G.703 advice and IEEE802.3 standard with independent intellectual property. It is a kind of remote transmission equipment transmitting 10 Base-T data. With an independent structure, TRXE1-10Base-T can transmit 10Base-T data through E1 channels and extend work distance of the interface between two Ethernets through E1 channels such as optical fiber, microwave DDN nets and so on. It can use the existing communication network structures and interfaces efficiently without impropriating optical fiber core or additional equipment.
The media converter transform the transmission media of Ethernet signal from CAT5 to optical fiber. it can extend the transmission distance ranges from several kilometer to hundred kilometer.
Media Converter is one technical product that was used to change the optic signal to electric signal,which help us solve the problem how transmitt the signals through a long distance,as the development of the information age,media converter become more and more popular, They are available between the fiber lines and cable lines.And they have obtained a big market in, telecommunications, broadcasting, railways, military, finacial, securities, customs civilaviation, shipping, local area network ,CATV Features 1.Support EEE802.3protocol,IEEE802.3u,100Base-TX,100Base-FX,IEEE802.3Z,1000Base-t Ethernet Standard 2.Support full-duplex and half-duplex transmission mode 3.Provide one or moer switching twisted pair ports of 10Mbps/100Mbps self_adaptive or 1000Mbps, 10Mbps/100Mbps/1000Mbps self adaptive and one 155Mbps or 1.25Gbps fiber interface. 4.Support up to 1552 byte long packet transmission 5.Supply the optical fiber transmission of dual-fiber multi-fiber,dual-fiber signel_mode and single-fiber single-mode. 6.External and internal power can be choosed 7.media converter with external power supply can match with 2U-14 slots rack and card-inserted type media converters can match with 2U-16 slots rack 8. Comprehensive LED 9. Port support Auto-MDI/MDIX automatic reverse Technical parameters 1.Transmission rate:10/100Mbsp,1000Mbsp, 10/100/1000Mbsp 2.Working wavelengh:850/1310/1550nm 3. Ethernet port:1/2/4port,Connect STP/UTPCat5 4. Fiber Connect:SC/FC/ST/SFP 5. Transmission Distance: 5.1 Dual-fiber and Multi-mode:2KM 5.2 Single-Fiber and Single-Mode:20/40/60/80KM 6.3Dual-Fiber and Single-mode:20/40/60/80/120KM 7.Power Input:AC110/220V,DC-48V,DC24V,DC12V,DC5V 8.Working Temperature: 10 ~ 50 9.Storage temperature: -40 ~ 70 10.Environmental humidity: 5% -90% 11.power consumption: 2.5W/8W Applications 1. apply to ready to rise to 10M extended enterprise network bandwidth 1000M 2. apply to images, voice and other multimedia data on an integrated transport network 3. point applies to the computer signal transmission in need of the occasion 4. widely used for computer data transmission network to meet a variety of business needs 5. apply to the campus broadband network, broadcasting network and intelligent residential broadband fiber-to-floor fiber to the home data transfer 6. with the switches and other computer network equipment can be combined to form:-chain, star, ring-type network and other computer networks 20-5000/ 0.67KG 27*16*6(CM)
SPC-10/100/1000M Series Media Converter can be used in the telecommunication IP MAN broadband optical network solution for its steady performance and powerful function.It convert 1000bps Ethernet copper port to optical port,up to 80km distandce on single-mode fiber without any relay device.It support auto-sending 10/100/1000Mbp half/full duplex topology,and MDI/MDI-X auto recognize. Selectable SC, FC, ST optical port makes the networks more flexible and feasible for the possibility of cost reduction. Package: carton Size:22X16X8cm.
Media converter In conformity to ieee 802.3 10 base-t standard. In conformity to ieee 802.3u 100 base-tx/fx standard. Max. 2m buffer memory built in chip. Back pressure flow control for full duplex ieee802.3 xand half duplex. Automatic identification of mdi/mdi-x cross line. High-performance1.4gbps memory bandwidth. In conformity to safety code of fcc and 15 class a and ce mark. Outside power supply:26mm*71mm*94mm Built-in power supply:40mm*110mm*140mm
1.Product Description Gigabit Fiber Media Converter with 10/100/1000M single mode Single Fiber Converter is the conversion equipment of Ethernet optical-electronic signals between 10/100/1000M UTP interface (TX) and 1000M Fiber interface (FX). The traditional 10/100/1000M Ethernet can be extended to the distance of 100km through Single Optical Fiber link. The performance and quality of the products are excellent because of adopting latest IC from Taiwan. It must be used in couples, because the transmitted optical differs from the receive optical in wavelength. 6 Group LED indicated lights could fully monitor the working conditions of Converters. It is easy for end-users to observe the conditions of network. The Series product with reasonable price is especially designed for network end-users. There are also many other advantages such as isolation protection, good data security, working stability and easy maintenance. 2.Technical Parameters Technical Parameters for 10/100/1000M Adaptive Fast Ethernet Optical Media Converter Number of Network Ports1 channel Number of Optical Ports1 channelFTTH 10/100/1000M WDM Gigabit Ethernet Fiber Optic Media Converter Transmission Rateself-adaptive 10/100/1000M Protocol supportedIEEE802.3/IEEE802.3U etc. Fiber TypeSingle Fiber Optic modeSingle Mode Transmission modehalf / full duplex Overall Power
1.Introduction 10/100M adaptive fast Ethernet optical media converter is a new product used for optical transmission via high-speed Ethernet. It is capable of switching between twisted pair and optical and relaying across 10/100 Base-TX and 100 Base-Fx network segments, meeting long-distance, high-speed and high-broadband fast Ethernet workgroup users needs, achieving high-speed remote interconnection for up to 120 km's relay-free computer data network. With steady and reliable performance, design in accordance with Ethernet standard and lightning protection, it is particularly applicable to a wide range of fields requiring a variety of broadband data network and high-reliability data transmission or dedicated IP data transfer network, such as telecommunication, cable television, railway, military, finance and securities, customs, civil aviation, shipping, power, water conservancy and oilfield etc, and is an ideal type of facility to build broadband campus network, cable TV and intelligent broadband FTTB/FTTH networks. 2.Features In accordance with Ethernet standards IEEE802.3 10Base-T, IEEE802.3u 100Base-T and 100Base-FX Supported Ports: SC for optical fiber; RJ45 for twisted pair Auto-adaptation rate and full/half-duplex mode supported at twisted pair port Auto MDI/MDIX supported without need of cable selection Up to 6 LEDs for status indication of optical power port and UTP port External and built-in DC power supplies provided 128 K's data buffer RAM Support for low-delay time pure data transmission and full/half-duplex flow control. Built-in watch-dog timer to monitor any error in internal data exchange
