Ethernet Fiber Optic Media Converter

Features:
-Broadcast filtering, address auto learning and auto-update feature and th operating mechanism of store and forward.
-Cache size: 256KB, address table size: 4KB
-Ethernet 10Base-T or 100Base-TX or 1000Base-T to 1000Base-LX fiber optic media converters
-Support IEEE 802.3, IEEE 802.3U, IEEE 802.3X, IEEE 802.3z/AB, IEEE802.1d
-Supports full-duplex or half-duplex backpressure flow control flow control, and with Auto-Negotiation function
-Interface supports 1000Mbps, 100Mbps, 10Mbps, can use with notthe same rate.
-TX/RX dual-header Standard SC interface
-Electronical interface supports 10Mbps, 100Mbps, 1000Mbps
-Automatically adapt , optical interface work rate 1000Mbps port
-Integration of high-quality photovoltaic modules to provide good optical properties and electrical properties to ensure reliable data transmission
-Status LEDs on link/connection status, dynamic data transfer/ full duplex / half duplex/rate status.
-Provides one RJ-45 interface supports auto-electrical cross connect switches, hubs
-Power Consumption: 4.5 W (Power adapter input AC-85V~ 265V)
-Over 50,000 hours consistent working period.

Transmission fiber:
Multi-mode: 50/125, 62.5/125 or 100/140166;204;m
Single-mode: 8.3/125, 8.7/125, 9 / 125 or 10/125166;204;m
Operating temperature :0-50 161;227; C
Storage temperature: -40-70 161;227; C
Humidity: 5% -90% non condensing.

Optical Line Protection (OLP) system is a new optical line protection subsystem developed with advanced technology of dynamic and synchronous optical switches. When communication quality is lower or equipment breaks down due to accidental fracture or bigger loss of optical fiber in the optical transmission line, the OLP system can switch the primary line to the secondary line within a short time, to ensure normal operation communication of line, which effectively prevent fiber or equipment fault and shorten the recovery time from hours to milliseconds.

Optical Line Protection switch provides both Manual and Automatic switching mode. In Manual mode, the system switches optical path only based on the commands from user.
In the Automatic mode, the system switches based on the power level detected and the preset threshold. Under automatic mode, the system can be set to be revertive or Non-revertive modes.
Under Revertive mode, the system switches back to the working path automatically after the fault condition is cleared. Under Non-revertive mode, the system does not switch back. The OLP models fit HT6000 Series CH04, CH08, CH20 Chassis.

EDFA Optical Amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). Integrated VOA can be automatically adjusted to achieve smooth gain spectrum. It can amplify the C-Band signal with or w/o middle stage access (MSA), which brings great flexibility for the network application.

C-band optical signal overall amplification
Covering the wavelength range of 1528 ~ 1565nm
Support systems to achieve different cross-section radio repeater transmission

Wide operating wavelength range:1528nm~1565nm
Three Optical Amplifier C-Band applications:
Booster
ï??n-line
Pre-amplifier
Low noise figure: typical: 5dB
Excellent gain flatness
Multiple operating modes:
AGC adjustable Gain
APC output is adjustable
ACC voltage adjustable
Mid-stage access for DCM or OADM
Optional OSC channel for remote management
MON port, on-line monitoring optical power and OSNR

Many model options serve all the traditional amplifier applications in an extended optical link: booster, in-line, and pre-amplifier.

A booster amplifier operates at the transmission side of the link. It features high input power, high output power, and medium optical Gain . Boosters are designed to amplify aggregated optical input power for reach extension.

An in-line amplifier operates in the middle of an optical link. It features medium to low input power, high output power, high optical Gain , and a low noise figure. In-line amplifiers are designed for optical amplification between two network nodes on the main optical link.

A Pre-amplifier operates at the receiving end of an optical link. It features medium to low input power, medium output power, and medium Gain. Pre-amplifiers are designed for optical amplification to compensate for losses in a demultiplexer located near the optical receiver.

Some EDFA Models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility. New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.

Some EDFA Models include a Red and a blue port designed for Single fiber DWDM Solution. The design of these models is used for single-fiber DWDM transmission systems.

1.Product Description

Gigabit Fiber Media Converter with 10/100/1000M single mode Single Fiber Converter is the conversion equipment of Ethernet optical-electronic signals between 10/100/1000M UTP interface (TX) and 1000M Fiber interface (FX). The traditional 10/100/1000M Ethernet can be extended to the distance of 100km through Single Optical Fiber link. The performance and quality of the products are excellent because of adopting latest IC from Taiwan. It must be used in couples, because the transmitted optical differs from the receive optical in wavelength. 6 Group LED indicated lights could fully monitor the working conditions of Converters. It is easy for end-users to observe the conditions of network. The Series product with reasonable price is especially designed for network end-users. There are also many other advantages such as isolation protection, good data security, working stability and easy maintenance.

2.Technical Parameters
Technical Parameters for 10/100/1000M Adaptive Fast Ethernet Optical Media Converter

Number of Network Ports1 channel
Number of Optical Ports1 channelFTTH 10/100/1000M WDM Gigabit Ethernet Fiber Optic Media Converter
Transmission Rateself-adaptive 10/100/1000M
Protocol supportedIEEE802.3/IEEE802.3U etc.
Fiber TypeSingle Fiber
Optic modeSingle Mode
Transmission modehalf / full duplex
Overall Power

Technical parameter
1.Standards:ieee802.3u fast ethernet 10/100base-tx and 100base-fx
2.Connectors:(rj45-utp and fiber sc)
3.Led:power.Fdx/col, fx-link/act, txlink/act, fx100.Tx100
4.Data tranfer mode: 10/100mbps
5.Duplex mode :full or half duplex mode
6.Power requirement:ac 100-260v dc1a +5v
7.Ambient temperature:0 - 70degree
8.Humidity:5% - 90%(noncondensing)
9.Dimenstons:26*71*97mm
10.Cable:cat.5 utp cable
11.Fiber: multi-mode
Specification
Connector type: sc
Typical distance: 60km
Fiber type: singlemode
Wavelength: 1310nm
Min tx pwr: -5.0dbm
Max tx pwr: -1.0dbm
Sensitivity: -35.0dbm
Link budget: 29.0dbm

10gbps media converter, 90 to 240v ac, 12v dc adapter power source type
Specifications:

Interface:

Left side:

One 10gbps rj-45 port
One 10gbps sfp + port (mini-gbic)

Right side:

One rs-232 console port (rj-45 connector)
One power jack

Wire speed cable length: up to 100m cat6a cable for wire speed transmission
Transceiver (phy), teranetics chip for 10gbase-t and net logic chip for 10gbase-r
Temperature:

Main features
In conformity to IEEE 802.3 10 Base-T standard. In conformity to IEEE 802.3u 1000 Base-TX, IEEE802.3z, IEEE802.3abstandard
Built in high efficiency SRAM for packet buffer, with 1K-entry lookup table and 4-way associative hash algorithm
Half duplex: back pressure flow control
Full duplex: IEEE802.3x flow control
Automatic identification of MDI/MDI-X cross line
Technical parameter:
Standard protocol: IEEE802.3 10 Base-T standard, IEEE 802.3u 1000Base-TX and IEEE802.3z standard
Connector: one UTPRJ-45 connector, one SC/ST connector
Operation mode: full duplex mode or half duplex mode
Power supply parameter:
Adapter(External): 110-265V AC input, 5V1A DC output
Power(Internal): 110-265V AC input, 5V1A DC output
Environmental temperature: 0 - 50
Relative humidity: 5%-90%
TP cable: Cat5 UTP cable
Transfer fiber:
multi-mode: 50/125, 62.5/125 or 100/140ª¦m
single mode: 8.3/125, 8.7/125, 9/125 or 10/125

Dimensions:
Power external: 94mm(L)x 71mm(W) x 26mm(H)
Power internal: 150mm(L) x 110mm(W)x 28mm(H)