APG Clamping Machines factory 1.high quality clamping mould 2.Supply APG moulds 3.Experienced engineers 4.Long life service Main Technical Parameters 1.Volmet China supplier Automatic pressure epoxy insulator hydraulic APG injection machine 2.APG machine Application: APG machine is applicable for small-sized products such as transformer, bushing, post insulator, contact cover, sensor, various supports, etc. Products 1:Good product quality, fine surface finish of products without bubbles. 2:High efficiency and high automation,only need 1/2 workers operate APG machine,efficiency greatly raised but the intensity of labor is decreased. 3:Chemical resistance,electrical insulation,strength resistance greatly improved. APG machine work process
APG Clamping Machines factory 1.high quality clamping mould 2.Supply APG moulds 3.Experienced engineers 4.Long life service Main Technical Parameters 1.Volmet China supplier Automatic pressure epoxy insulator hydraulic APG injection machine 2.APG machine Application: APG machine is applicable for small-sized products such as transformer, bushing, post insulator, contact cover, sensor, various supports, etc. Products 1:Good product quality, fine surface finish of products without bubbles. 2:High efficiency and high automation,only need 1/2 workers operate APG machine,efficiency greatly raised but the intensity of labor is decreased. 3:Chemical resistance,electrical insulation,strength resistance greatly improved.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Epoxy Resin
WE ARE SUPPLYING FROM INDIA AND FAR EAST
We deals in the following products :- 1) PVC Resin 2) Caustic Soda Flakes
These cast iron skulls are a by-product derived from the cast iron foundries. The byproduct is a ferrous by-product which can be utilised in an electric arc furnace to produce crude steel. Physical Description On visual inspection, it appears to be made up of irregular shapes. The material is separated by magnet and screener. Packing: Loose in container Loading: in 20 Container For further information, please feel free to contact us.
Cast Iron Skulls
Nitrogen - 46% min Moisture - 1% max Biuret - 1% max Prilled - 0.85-2mm Granular - 2-4mm 90-94%min color - Pure White Radiation - Non-Radiactive Free Ammonia - 160pxt ppm max
Fuel LPG. Fuel Tank Capacity 2.0 L Fuel Consumption : App. 225 g P/H Length : 350 mm Height : 330 mm Width : 150 mm Weight(kg) Empty : 1.5 Kg (Empty)
Crystals Benzoin Siam Crystals
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
Main technical parameters Model -450J VOL-240J VOL-360J Nominal diameters of enameled wire Ï?0.1~1.5mm Ï?0.1~1.5mm Ï?0.1~1.5mm Max rotation diameter of coil Ï?450mm Ï?240mm Ï?360mm Min rotation diameter of coil Ï?50mm Ï?50mm Ï?50mm Max winding breadth 400mm 210mm 350mm Winding rotation speed rang 1390rpm 1390rpm 1390rpm Machine tool power 1.5kW 0.75kW 1.5kW Input power of machine tool 220V±10% 220V±10% 220V±10% Outline size of machine tool 1500*600*1450mm 1300*550*1300mm 1300*550*1400mm Color Blue,Calx,Customizable Blue,Calx,Customizable Blue,Calx,Customizable
PA66 FR regrind black color Pa6 / pa66 is mainly applied as follows: 1. Improves nylon water absorption and improves size stability of the product. 2. Improved nylon fire resistance to meet the requirements of electronics, electrical, communications and other industries. 3. Improved mechanical strength of nylon to achieve the strength of metal materials, metal replacement. 4. Improves nylon low-temperature resistance and enhanced resistance to environmental stress. 5. Improves nylon wear resistance to meet high wear resistance requirements. 6. Improves nylon antistatic properties to meet its extraction requirements and mechanical applications. 7. Improves nylon heat resistance to adapt to high temperature conditions such as car engines. 8. Reduce nylon cost and improve product competitiveness. Through the above modification, high performance and functionalization of nylon composite materials are realized, thereby promoting the development of industries involving high performance and high quality. MATERIAL : PA66 FR regrind black color CATEGORY : PA66 FG TYPE : Regrind GRADE : Black color SPECIFICATION : GF50. 1 full container available Origin : Tunisia LOADING WEIGHT 23 Ton FOB (USD/Ton) : 750$ - 950$ Packaging : Jumbo Bag Est. Shipping Time: 15, 30, 45 days
HIPS repro pellet mixed color from yoghurt caps HIPS Recycled Pellets Thermoplastics PS has two representatives, GPPS and HIPS. In particular, PS HIPS plastic is the most popular to many advantages and applications. HIPS belongs to the group of hard, transparent resins that are easy to create color, processed by laminating film lamination and easy laminating technology. What is HIPS PLASTIC ? HIPS pellet stands for High Impact Polystyrene. Polystyrene has the chemical formula Polystyrene (C8H8)n which is a long chain hydrocarbon in which alternating carbon centers are attached to the phenyl group (the name given to the aromatic benzene ring). MATERIAL: HIPS repro pellet mixed color from yoghurt caps CATEGORY: HIPS repro TYPE: Pellet GRADE: Mixed color SPECIFICATION: Mixed color.from yoghurt caps Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 900$ - 1150$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
PC Water bottle blue color MATERIAL: PC Water bottle blue color CATEGORY: PC TYPE: Water bottle GRADE: Black color SPECIFICATION: PC water bottle,blue color.15 tons available Origin: Tunisia LOADING WEIGHT: 23 Ton FOB (USD/Ton): 1350$ - 1550$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days
PC/ABS regrind full container available MATERIAL : PC/ABS regrind full container available CATEGORY : PC/ABS TYPE : Regrind GRADE : Black color SPECIFICATION : 1 full container available Origin : Tunisia LOADING WEIGHT : 23 Ton FOB (USD/Ton:) : 850$ - 1000$ Packaging : Jumbo Bag Est. Shipping Time : 15, 30, 45 days
PET Airbag scrap with silicon MATERIAL : PET Airbag scrap with silicon CATEGORY : PET TYPE : Airbag SPECIFICATION : 2 full container available Origin : Tunisia LOADING WEIGHT : 19 Ton FOB (USD/Ton) : 450$ - 550$ Packaging : Jumbo Bag Est. Shipping Time 15, 30, 45 days
2Lians can supply LLDPE product as below: PET Bottle In Bales MATERIAL: LLDPE REPRO PELLET MIX COLOR CATEGORY: LLDPE TYPE: PELLET GRADE: FILM GRADE SPECIFICATION: Lldpe repro pellet made from postindustrial film,origin japan,MFI:1~3,MESH:100 Origin: JP LOADING WEIGHT: 26 FOB (USD/Ton): 720-800
