Vacuum residue after heat exchanged with feedstock oil, it enters in to oxidation tower. As air is blowing from the bottom of oxidation tower, vacuum residue in the tower is oxidizing reacting with air. Fresh water is sprayed from the top of oxidation tower to control the temperature of gaseous phase temperature not higher than 160 c. Tail gas from the top of oxidation tower will flow in to a saturator, tail gas contact with water and cooled down to have the dirty oil separated away from gas. The residual gas discharged from the top of saturator will flow in to water sealed tank. And residual gas discharged from the top of water sealed tank will be sent to residual gas incinerator, which will be discharged to air after burnt in a incinerator. The heat energy produced from tail gas can be used for heating up of the feedstock oil before entering in to vacuum tower. The dirty oil discharged from saturator will flow in to residual oil tank, and then pumped out of unit periodically. Circulating diesel is pumped in to asphalt-diesel heat exchanger through diesel circulating pump to make its temperature increased from 65c to 140c. The hot diesel will be cooled through diesel cooler with circulating water to have it down to 65c. The cooled diesel will be sent back to diesel circulating tank. Compressed gas from the system pipe lines enters in to bottom of oxidation tower. Saturator, residual oil tank, diesel tank are in the same case. The degree of asphalt from 60-120 is controlled by the vacuum distillation extraction level, oxidation duration and air blowing quantity. Wooden case
Bitumen ( Asphalt) 40/50, 40/60, 50/70, 60/70, 70/100, 80/100 and 85/100
Bitumen Product Description : Bitumen is widely used in the construction of asphalt roads and bituminous membrane products. Bitumen is commonly used to build highways, motorways and rail networks. Bitumen has excellent water-proofing properties and is widely used for making roofing products along with a range of other household and industrial applications, from emulsion paints to sound-proofing. Penetration Bitumen and Bitumen Emulsions are used for the construction of railway tracks and by using special types of bitumen such as Polymer Modified Bitumen, the vibration and noise levels are reduced due to a dampening effect. Bitumen has been proven to be effective on both high-speed railway tracks and heavy load railway tracks. Bitumen is also used for surfacing airfield runways and air strips (PMB is preffered due to its fuel resistant properties) and taxi ways. For the Marine construction industry bitumen is used for hydraulic applications such as canal lining, underwater tunnels, river bank protection, dam construction and sea defences. There are also numerous industrial applications like roofing felt material, printing inks, packaging paper, linoleum, electrical cable / Junction box insulation, mastic for roofing of terraces, and duplex paper manufacture. Price of product ( USD price or FOB price) : 3.000 MT monthly market price. 10.000 MT monthly market price Less 5%. Product origin : Russia and Non Russia Key Specifications/Special Features : Specifications for types/grades of Oil Bitumen according to buyer specifications and/or will be given upon received buyer credible purchase request in the form LOI/ICPO docs. Minimum Order Size and Packgaing details : MOQ 3000 MT Bulk in tanker vessels. Drums 150/180/200 Kg. Jumbo bags 1000 Kg. Poly bags 32 Kg. Tanks 20 MT.
We are supplier and exporter of Bitumen. Bitumen is used in road construction due to various properties and advantages. The bitumen as a raw material in flexible road construction and bitumen as a mix (composing other materials i.e. aggregates etc.) serves certain advantages, that prompt to use bitumen widely in road construction.
Bitumen, a highly viscous and black hydrocarbon, plays a crucial role in civil engineering due to its remarkable properties and versatile applications. As a binder in asphalt mixes, it provides durability, strength, and resistance to traffic and climate-induced stresses. Commodity: Bitumen Grades 35/50, 40/50, 50/70, 60/70, 70/100, 80/100 & VG3 Quantity available: Min 100MT and Max 50,000 MT/ Month. Packing: New steel drum, 110 drums fitted in 20ft' container A) Steel Thickness: 0.6 MM B) Height :980 MM C) Diameter: 50 CM Terms of Payment: Irrevocable, Confirmed, Non-Transferable LC 100% at Sight via Dubai OR 30% Cash in Advance and 70% balance against Custom Clearance Documents.
We offer premium-grade bitumen, essential for road construction and infrastructure projects. Our bitumen ensures durability and reliability, meeting international standards for quality and performance.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Place of Origin Gansu, China Brand Name H Model Number 30/40/50/60/70/80 Softening Point 46 Product Name bitumen Color black Package drum /bag MOQ 1FCL Sample available
Maximum : 100,000 MT/Month
60/70 80/100 Other On Request
- Grade 40-50: Suitable for road construction and repair. - Grade 60-70: Ideal for general paving applications. - Grade 85-100: Used in various industrial applications.
BITUMEN/PETROLEUM ASPHALT Requirement from Buyer is a Mast to answer your inquiries. 1. PRODUCT: 2. QUANTITY: 3. DESTINATION: 4. TERM CONTRACT Only ): 5. PAYMENT TERM: 6. TARGET PRICE: 7.Letter of Intent (LOI)
Functional Bitumen Used primarily in road construction and waterproofing, it offers high durability and resistance to water.
The term bitumen refers to a substance produced through the distillation of crude oil Bitumen is known for its waterproofing and adhesive properties and is commonly used in the construction industry notably for roads and highways The two Bitumen grades are 6070 and 80100 The difference between 6070 and 80100 penetration grade is the penetration range Bitumen 6070 has lower penetration which means it is harder than bitumen 80100 Bitumen 6070 is better suited for use in hot climates and can withstand heavy traffic loads unlike bitumen 80100 According to the ASTM D36 method the softening point of bitumen 6070 is between 49 to 56C and the flash point of bitumen 6070 is 250 C Another important factor is density Due to the ASTM D70 the density of bitumen 6070 is equal to 10344 Bitumen Penetration Grade 85100 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses
Bitumen is a black, semi-solid or liquid substance with high viscosity produced by the non-destructive distillation of crude oil during petroleum refining. The core industry using bitumen is road construction (asphalt) and another significant field is the building industry (roofing membranes, water-proofing felts)
Bitumen Grade 60/70 And 80/100 As Per Seller Procedure only. Dip and pay CIF FOB
Bitumen produced by refineries in the Russian Federation, Kazakhstan, and elsewhere, is available for sale FOB or CIF at the best prices. Prices are negotiable for serious big-volume buyers. Buyer's mandate welcome. 30/40 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 40/50 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 50/70 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 60/70 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 80/100 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 85/100 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 100/120 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT
We are supplier of best quality Bitumen. We can supply you with best quality original Bitumen at a fair price. We also provide samples and any required lab certificates. Please let me know if you are interested in our products and if you needed any other info, Iâ??ll be glad to assist.
Product Name: Bitumen Quality: Top Quality Delivery Time: 5-7 Days Packaging: Custom Customization Orders: Accepted We Are The Wholesale Supplier and Exporter Of *Bitumen*. Bulk Stock Available for Worldwide Delivery Contact Us For More Information.
Bitumen is known for its waterproofing and adhesive properties and is commonly used in the construction industry, notably for roads and highways. Production occurs through distillation, which removes lighter crude oil components like gasoline and diesel, leaving the heavier bitumen behind. Bitumen deposits can also occur naturally at the bottom of ancient lakes, where prehistoric organisms have decayed and been subjected to heat and pressure. Wholesale Bitumen
