Vacuum residue after heat exchanged with feedstock oil, it enters in to oxidation tower. As air is blowing from the bottom of oxidation tower, vacuum residue in the tower is oxidizing reacting with air. Fresh water is sprayed from the top of oxidation tower to control the temperature of gaseous phase temperature not higher than 160 c.
Tail gas from the top of oxidation tower will flow in to a saturator, tail gas contact with water and cooled down to have the dirty oil separated away from gas. The residual gas discharged from the top of saturator will flow in to water sealed tank. And residual gas discharged from the top of water sealed tank will be sent to residual gas incinerator, which will be discharged to air after burnt in a incinerator. The heat energy produced from tail gas can be used for heating up of the feedstock oil before entering in to vacuum tower.
The dirty oil discharged from saturator will flow in to residual oil tank, and then pumped out of unit periodically. Circulating diesel is pumped in to asphalt-diesel heat exchanger through diesel circulating pump to make its temperature increased from 65c to 140c. The hot diesel will be cooled through diesel cooler with circulating water to have it down to 65c. The cooled diesel will be sent back to diesel circulating tank.
Compressed gas from the system pipe lines enters in to bottom of oxidation tower.
Saturator, residual oil tank, diesel tank are in the same case.
The degree of asphalt from 60-120 is controlled by the vacuum distillation extraction level, oxidation duration and air blowing quantity.
Wooden case
Bitumen ( Asphalt) 40/50, 40/60, 50/70, 60/70, 70/100, 80/100 and 85/100
Bitumen Product Description : Bitumen is widely used in the construction of asphalt roads and bituminous membrane products. Bitumen is commonly used to build highways, motorways and rail networks. Bitumen has excellent water-proofing properties and is widely used for making roofing products along with a range of other household and industrial applications, from emulsion paints to sound-proofing. Penetration Bitumen and Bitumen Emulsions are used for the construction of railway tracks and by using special types of bitumen such as Polymer Modified Bitumen, the vibration and noise levels are reduced due to a dampening effect. Bitumen has been proven to be effective on both high-speed railway tracks and heavy load railway tracks. Bitumen is also used for surfacing airfield runways and air strips (PMB is preffered due to its fuel resistant properties) and taxi ways. For the Marine construction industry bitumen is used for hydraulic applications such as canal lining, underwater tunnels, river bank protection, dam construction and sea defences. There are also numerous industrial applications like roofing felt material, printing inks, packaging paper, linoleum, electrical cable / Junction box insulation, mastic for roofing of terraces, and duplex paper manufacture. Price of product ( USD price or FOB price) : 3.000 MT monthly market price. 10.000 MT monthly market price Less 5%. Product origin : Russia and Non Russia Key Specifications/Special Features : Specifications for types/grades of Oil Bitumen according to buyer specifications and/or will be given upon received buyer credible purchase request in the form LOI/ICPO docs. Minimum Order Size and Packgaing details : MOQ 3000 MT Bulk in tanker vessels. Drums 150/180/200 Kg. Jumbo bags 1000 Kg. Poly bags 32 Kg. Tanks 20 MT.
We are supplier and exporter of Bitumen. Bitumen is used in road construction due to various properties and advantages. The bitumen as a raw material in flexible road construction and bitumen as a mix (composing other materials i.e. aggregates etc.) serves certain advantages, that prompt to use bitumen widely in road construction.
Maximum : 100,000 MT/Month
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
BITUMEN/PETROLEUM ASPHALT Requirement from Buyer is a Mast to answer your inquiries. 1. PRODUCT: 2. QUANTITY: 3. DESTINATION: 4. TERM CONTRACT Only ): 5. PAYMENT TERM: 6. TARGET PRICE: 7.Letter of Intent (LOI)
Bitumen, a highly viscous and black hydrocarbon, plays a crucial role in civil engineering due to its remarkable properties and versatile applications. As a binder in asphalt mixes, it provides durability, strength, and resistance to traffic and climate-induced stresses. Commodity: Bitumen Grades 35/50, 40/50, 50/70, 60/70, 70/100, 80/100 & VG3 Quantity available: Min 100MT and Max 50,000 MT/ Month. Packing: New steel drum, 110 drums fitted in 20ft' container A) Steel Thickness: 0.6 MM B) Height :980 MM C) Diameter: 50 CM Terms of Payment: Irrevocable, Confirmed, Non-Transferable LC 100% at Sight via Dubai OR 30% Cash in Advance and 70% balance against Custom Clearance Documents.
Bitumen produced by refineries in the Russian Federation, Kazakhstan, and elsewhere, is available for sale FOB or CIF at the best prices. Prices are negotiable for serious big-volume buyers. Buyer's mandate welcome. 30/40 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 40/50 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 50/70 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 60/70 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 80/100 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 85/100 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT 100/120 FOB $300 Gross / $290 Net per MT - CIF $330 Gross / $320 Net per MT
Bitumen a black viscous mixture of hydrocarbons obtained naturally or as a residue from petroleum distillation. It is used for road surfacing and roofing. Bitumen is a mixture of Organic Liquids that are highly Viscous, Black, Sticky, Entirely Soluble in Carbon Disulfide, and composed primarily of highly condensed Polycyclic Aromatic Hydrocarbons. Naturally occurring or crude bitumen is a sticky, tar-like form of petroleum which is so thick and heavy that it must be heated or diluted before it will flow. At room temperature, it is much like cold molasses. Refined Bitumen is the residual (bottom) fraction obtained by fractional distillation of crude oil. It is the heaviest fraction and the one with the highest boiling point, boiling at 525 C (977 F). Petroalliance are involved in import and the supply and trade of Bitumen Oil. This oil is a dark and viscous liquid which is sticky in texture. It is widely used in road construction, waterproofing, paints, enamels etc. It is available to clients in different types of settings at highly affordable prices. It is widely acclaimed amongst our client base for its supreme quality. Uses of Bitumens Bitumen is primarily used for construction and paving of roads. Its other uses are for Bituminous Waterproofing Products, including the use of bitumen in the production of roofing felt and for sealing flat roofs.
