ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. ADSS Tension Clamp Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters.
ADSS with The DN Short-span Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The ADSS tension clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters. Easy installation and maintenance. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods
OEM ADSS Tension Clamp Pre-twisted tension clamps are also known as pre-twisted dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. Pre-twisted dead end is a tension clamp that plays an important role in ADSS/OPGW transmission lines. Dead-end fiber optic cable clamps are used to connect ADSS/OPGW/OPPC to overhead towers or poles. The unique design of the pre-fabricated tension clamps not only simplifies installation, but also ensures a secure cable connection. Dead-end cable clamps provide superior performance in protecting ADSS/OPGW/OPPC cables from stress point damage and preventing signal degradation during transmission. Pre-twisted tension clamps and pulling dead-end cable clamps used on conductors and ground wires are similar in appearance, but the specifications, raw materials, and strength requirements of the two types of pulling dead-end cable clamps are quite different. Although there are different design standards in different countries, we can make OEM according to customers' requirements.
Custom ADSS Tension Clamp ADSS Tension Clamps are used to connect ADSS cables to poles/towers. Armored rods provide protection and cushioning for the ADSS cables. The special design of the prefabricated rods ensures that the tension clamps do not overstress the ADSS cables, thus ensuring a normal service life of the cable system.The ADSS tension clamps are made of aluminium-clad or galvanized steel wire. Structure and raw materials Unshackle - hot-dip galvanized steel. The shackle is connected to the reinforcing bar unit. Twisted chain ring - hot dipped galvanized steel. Twisted links are used to connect the shackle to the thimble. Sleeve - hot dip galvanized cast steel. The sleeve is inserted into the unclamp of the tension clamp to provide protection and connection. Armored rod ----- Aluminum clad steel wire. Armored rods increase friction through a layer of granular emery inside the cable. The rods are shop assembled into four subsets to minimize misalignment errors and speed installation. The ends are bent outward to provide strain relief in critical cable departure areas. Prefabricated Dead Ends - Prefabricated dead ends are made from hot-dip galvanized steel wire or aluminum-clad steel wire and are assembled in the shop into a subset with a solid layer of emery to increase the grip of the tensioning clamps while reducing lateral pressure. Direction 1. Used for connecting connecting poles (towers) to terminal poles (towers), tension poles, or poles (towers) with line clamping angles of 25�° or more. Special specifications: 1 unit for each terminal pole (tower), 2 units for each tension pole (tower), and 2 units for each connecting pole (tower). You can select the specification model corresponding to the appropriate cable diameter range, maximum allowable tension (MAT) or span length from the data sheet.
ADSS Preformed Short Span Tension Clamp Tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. China ADSS Tension Clamp ADSS tension clamps are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Features: 1. Component: preformed wire, rubber inserting, casting aluminum shell, right angle shackle, U shackle etc. 2. Usage: supporting,make ADSS cable hang on the pole and tower. 3. Features: a, stress on average, no concentration stress, protect cable better and increase the stiffness of cable in the mount point. b, good dynamic stress. It can provide enough grip strength(10%RTS) c, rubber inserting make abrasion low. d. excellent aluminum alloy improve the mechanical and resist-corrosion function, extend life. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods..
We also offer a versatile gamut of medicinal seeds that are made by some of the reputed manufacturers. They have expert scientists and researchers who perform the stiff duty of cross research and make sure that the quality of the products matches with international standards. We then make sure that the products that we are exporting are best in quality and therefore we have a team of quality monitoring system assigned for this job. In a very short span of time we have blossomed into one of the revered medicinal herb seeds and medicinal plant seeds suppliers from India. As part of our Medicinal Seeds Range, we offer high quality Crataegus Oxyacantha, which is a herbal plant whose berries are used for its medicinal qualities in several natural medicinal formulations. Available in pure and natural form, the Crataegus Oxyacantha Supplied by us, is tested for quality and medicinal properties.
Preformed tension clamp is also called preformed dead end or dead end cable clamp. The raw material of preformed tension clamp is aluminum clad steel wire or galvanized steel wire, For communication ADSS optical fiber, OPGW cable and OPPC. The unique pre-formed tension clamp design not only simplifies the installation but also ensures the safety of the cable connection. Terminal cable clamps provide excellent performance to protect ADSS/OPGW/OPPC cables from stress points and prevent signal drops during transmission. What is the raw material of the pre-formed tension clamp The raw material of the prefabricated tension clamp is aluminum-clad steel wire or galvanized steel wire. What is the purpose of prefabricated tension clamps Prefabricated tension clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. What are the types of prefabricated tension clamps The preformed tension clamp and guy wire dead end grips used on the conductor and earth wire look alike in shape, but there are really big differences in the specification, raw material, and strength requirement of the two types of guy grips. 1. Dead-end for short span ADSS Dead-end for short span ADSS with a small tension clamp material for aluminum-clad gang wire, mainly used for the corner towers, the middle of follow-tower and connecting the terminal tower, the largest installation file from the less than 100 meters. 2. Dead-end for medium/long span ADSS Dead-end for medium span ADSS in tension and large tension clamp material for aluminum-clad steel wire, mainly used for files larger than 100 meters away from the corner tower, the middle tower and Terminal Tower successive connection. As an experienced manufacturer and supplier of preformed tension clamps, Boersen Photoelectric is able to OEM to customer specifications. If you have any questions, please feel free to contact us.
ADSS Cable Suspension Clamp ADSS Suspension Clamps, also known as Prefabricated Suspension Clamps or AGS Suspension Clamps, offer a full range of aluminum cladding, rubber, armored clamps, bolts, and nuts to support and protect ADSS/OPGW cables from bending damage. Armored Clamp Suspensions can be customized for different gauges, various cable sizes, wire raw materials, and armored clamp suspension design options to precisely match the clamping strength, span, and cable type requirements, including Dual Suspension Clamps, AGS Suspension Clamps, Cushion Clamp Suspension Clamps, ADSS Cable Suspension Clamps, and OPGW Suspension Clamps. adss Suspension Clamps are specifically designed for use in applications where there is a large drop in long spans, river crossings, or on hills. The double suspension clips have a vertical breaking load of 100kn. as your OEM partner for prefabricated suspension clips, we can help you save money and stay competitive. Whether it is standard, customized or different types, Huaneng Clamp Suspension offers quality solutions for all market needs.
ADSS Downlead Clamp DownLead Clamp, also called lead wire pads, are fixed to poles or strain relief towers to guide fiber optic cables up or down through them. According to the application, the lead wire clips include tower lead wire clips, pole lead wire clips, ADSS lead wire clips and OPGW lead wire clips. Downlead Clamp DownLead Clamp, also called lead wire pads, are fixed to poles or strain relief towers to guide fiber optic cables up or down through them. According to the application, the lead wire clips include tower lead wire clips, pole lead wire clips, ADSS lead wire clips and OPGW lead wire clips. The downlead clamp consist of a stainless steel band and a rubber part. The stainless steel band is used to fix the rubber clip on the pole. At the same time, the rubber part fixes the optical fiber. This way, the fiber does not shake and at the same time reduces damage caused by friction. The lead wire clamps for towers have a different structure than the lead wire clamps for poles. The clamps consist of steel brackets, bolts and nuts, and rubber parts. The bolt secures the lead clip to the tower. Compared to other lead clip manufacturers, Huaneng offers the end user a wide range of lead clip design options. huaneng lead clips can be custom manufactured with a wide range of cables, materials and different connection options.
ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.
ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.
Wholesale ADSS Suspension Clamp An ADSS (All-Dielectric Self-Supporting) Suspension Clamp is a component used in the installation of ADSS fiber optic cables. ADSS cables are designed to be self-supporting and do not require any metallic elements for support, making them suitable for aerial installations in various environments, including power distribution lines, railways, and more. The suspension clamp is an essential part of the ADSS cable installation process, as it helps secure the cable to the supporting structures, such as poles or towers. The primary purpose of the ADSS suspension clamp is to maintain the appropriate tension on the cable while preventing excessive bending or stress that could negatively impact the cable's performance and longevity. ADSS suspension clamps are typically made of materials that are durable and resistant to environmental factors such as UV radiation, extreme temperatures, and moisture. They are designed to hold the ADSS cable securely in place while minimizing stress and strain on the cable itself. The installation process of ADSS suspension clamps involves attaching them to the support structure and then securing the ADSS cable in the clamp. This process ensures that the cable is held in the correct position and tension, optimizing its signal transmission capabilities and overall reliability. Features Durable Construction: ADSS suspension clamps are typically made from materials that are resistant to environmental factors such as UV radiation, extreme temperatures, and moisture. This durability helps ensure the longevity of the clamp in various outdoor conditions. Corrosion Resistance: The materials used in the construction of ADSS suspension clamps are often chosen for their resistance to corrosion, preventing degradation over time due to exposure to harsh weather conditions.
Description ADSS preformed tension clamp is designed for connecting and fastening the ADSS fiber to the overhead pole. Feature 1) quick and easy installation 2) distribute the stress uniformity 3) guarantee no cable damage or slipping 4) strong resistance to corrosion and cruel environment 5) made of aluminum alloy, aluminum clad steel and galvanized steel Order Tips 1- confirm the cable type 2- confirm the cable diameter 3- confirm the span and the rated tensile strength 4- the material can be aluminum alloy, aluminum clad steel or galvanized steel Our service 1, Fast Response Time 2, Quality and Certified Products3, Resonable Price 4, Cheap and Reliable Transportation 5, 7*24 Hours After Sales Service
Place of Origin -Hebei, China Product name -Suspension Clamp for ADSS Cable Cable Size -5-8mm Breaking Load -4kN Usage -Used ADSS cable Certification -ISO9001 / RoHs Service -OEM / ODM / Customized
Qucik detail Place of Origin Zhejiang, China Brand Name CROP Model Number Fiber optic cable clamp Product name Fiber optic cable clamp for ADSS cable Sample Free Material Plastic,stainless steel Company website www.cropgroupcn.com Quality Prime Installation Quick Certifications ISO9001 OEM Acceptable Export All over the world Business Type Manufacturer View File
Dead end grip for OPGW Component Inner armor rods, outer armor rods, thimble, U-shaped hanging loop, Extensioe Rods, bolt, nut, etc. Characteristic 1. Stress is distributed equally, without stress focus. It can protect optical cabl-es very well. 2. Under the condition of not exceeding the intensity of cable's side pressure, it has higher grip power for the cable, and can support higher tensile force. 3. The grip power for the cable is not less than 95% of rating's pulling resisting intensityof the optical cable, completely satisfying the needs of setting up the cable. Conditions For The Usage 1. Terminal poles/towers; 2. Corner poles/towers; 3. Dead-end poles/towers; Intensity According to the requirement of customers, 30kN, 70kN, 100kN, 120kN, etc, can be supplied. Select Chart Model Grip(KN) Length of Inner Armor Rods(mm) Length of Outer Armor Rods(mm) Estimated Weight(KG) Color ONZ-60-* * 60 1900 1500 2.9 Yellow ONZ-70-* * 70 2000 1600 3.5 Yellow ONZ-80-* # 80 2200 1700 4.2 Yellow ONZ-90-* # 90 2400 1800 4.3 Yellow ONZ-100-* # 100 2500 1900 4.5 Yellow ONZ-120-* # 120 2600 2000 5.0 Yellow Note: representing the outer diameter of the optical cable (mm).
ADSS Preformed Short Span Tension Clamp Preformed Tension Clamp are designed to hold conductors and strands evenly to prevent conductor deformation. This product is designed for bare and stranded conductors and is recommended for use with plastic sheathed conductors. At the same time, the tension clamp can withstand at least 95% of the rated breaking strength of conductors and strands, and is made of high-strength materials. Composition: twisted wire, rubber insert, cast aluminum shell, right-angle shackle, U-shackle. Purposes: supporting cableï¼?make the ADSS hang on the tower. Structure and Materials Shackle - Constructed from hot-dip galvanized steel, the shackle is linked to the reinforcing bar unit. Twisted Chain Ring - Made of hot-dip galvanized steel, the twisted links serve to connect the shackle to the thimble. Sleeve - Composed of hot-dip galvanized cast steel, the sleeve is inserted into the unclamp of the tension clamp to ensure protection and facilitate connection. Armored Rod - Fabricated from aluminum-clad steel wire, armored rods enhance friction through a layer of granular emery within the cable. These rods are pre-assembled into four subsets to reduce misalignment errors and expedite installation. The ends are bent outward to provide strain relief in critical areas where the cable departs. Prefabricated Dead Ends - These components are constructed from either hot-dip galvanized steel wire or aluminum-clad steel wire and are assembled in the shop into a subset featuring a solid layer of emery. This design increases the grip of the tensioning clamps while minimizing lateral pressure.
OPGW the Preformed Helical Tension Clamp The OPGW Premored/Helical Tension Clamp is primarily used to install cables with RTS less than 160 kN to tension towers/poles, corner towers/poles and terminal towers/poles. A complete set of OPGW prefabricated/spiral tensioners includes aluminum alloy or aluminum clad steel dead ends, structural reinforcement rods, support fittings and grounding clamps, etc. Wire Tension Clamp An OPGW (Optical Ground Wire) wire tension clamp is a specialized device used in the installation and maintenance of OPGW cables. OPGW cables are composite overhead cables that combine optical fibers for communication purposes with a metallic ground wire for power transmission and grounding. The OPGW wire tension clamp serves the purpose of securely attaching the OPGW cable to the supporting structure, such as poles or towers, while maintaining the necessary tension. It plays a crucial role in ensuring the stability and reliable performance of the OPGW system.
OPGW Preformed Double Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. Preformed Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. The unique pre-formed tension clamp design not only simplifies installation, but also ensures a secure cable connection. Dead-end cable clamps provide superior performance to protect ADSS/OPGW/OPPC cables from stress point damage and prevent signal degradation during transmission. Pre-formed tension clamps for conductors and grounds are similar in appearance to pulling dead-end clamps, but the specifications, raw materials and strength requirements of the two types of pulling clamps do differ significantly. Although there are different design standards in different countries, we can OEM to customer requirements. As an experienced manufacturer and supplier of preformed tension clamps, Seinei understands the standards, the manufacturing process and understands your needs. If you have any questions, please feel free to contact us.
Tension Clamp for Earth Wire Tension Clamp For Earth Wires are for use by trained craftsmen only. Dead-end clamps should not be used by anyone unfamiliar or untrained in their use. Wire Tension Clamp Tension clamps are designed to non-rigidly secure installation cables to brackets, fasteners on buildings, or utility poles. Cable clamps are installed at the beginning and end of cable runs, suspensions, branches and turns. Tension clamps can also be used where cables sag on large straight sections or form under the influence of increased tensile loads. The design of the products is simple. One of the most popular consists of a cone, a pair of plastic toothed wedges that act as clamping devices, and a steel ring. The principle of operation is simple and consists of self-tensioning the cable using the movable wedges of the clamp. The sale of tension clamps and their use significantly reduces the time and physical costs of installation work. This cable attachment element offers the following advantages There is no need to strip the insulation to expose the mating cable during use; Simple installation, reducing the possibility of errors; No special training of installers is required; No special tools are required to prepare cables for installation; Reduced risk of cable damage and compromised integrity.
