BR-60W CO2 POWER SUPPLIES Feature 1.Both analog signals of 0 to 5V and PWM signals are used� to control and regulate this AC110V CO2 power supplyâ??s output laser power. 2.This AC110V CO2 power supply� can adopts� ether external LCD digital display module by network cable,which can show� HV carbon dioxid power supplyâ??s working current,working statues and failure code.� It is very good function for both machine factory and machine users 3.This BR-60W CO2 power supply uses ordinary H/L/P/G/IN/5V terminal block� to input� laser control signal and black� steel case. 4.This LCD screen CO2� power supply� has� high efficiency and� quick� response with its zero current half bridge soft switching circuit. Thus it is easy to cooperate with most brand 60W co2 laser tube.� 5.This 60W CO2� laser power supply� terminal control is simple and adapted to high and low level signals. TTL 1level can be used to control the start and stop of laser� power. At the same time, an abnormal protection switch was added to detect if� the external water is ventilated or not. 6.The HV carbon dioxide power supply use one PCS fan for cooling. It use Japanâ??s bearing and make the fan works for very long time. 6.This HV carbon dioxide� power supply� has good grounding protection5.With advanced open circuit protection, the� 60W CO2 power supply� can work in an open-circuit state for a short time, which can avoid the damage of the LCD screen CO2 power supply� caused by the bursting of the laser tube. Specification lnput� Input voltage AC220V�±10%� (AC110V specified while order) AC frequency 47~440HZ Maximum input power 490W Maximum input current 2.2A Output Maximum output voltage 25KV Maximum output current 28mA (depending� on the laser tubes of different manufacturers) Efficiency More than 90%� (Full load) Response speed Not more than 1ms Control lnterace TTL multilevel switching control,effective level can be high and low selection (see control wining diagram) Insulation lnput-output AC 1500V 1 minutes not more than 10mA lnput-shell AC 1500V 1 minutes not more than10mA Output-shell Connection Open Circuit Protection Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc) Environmental Requested Working temperature -10â??~50â?? Storage of temperature -20â??~75â?? Relative Humidity Maximum 85%RH (non-condensing) Altitude 100,000 feet of work 200,000 feet of storage,dose not work Cooling methods Forced air cooling (fan cooling) Dimensions (LxWxH) 210mmx145mmx102mm
Commodity : Potassium sorbate Molecular formula : C6H7KO2 Molecule Weight : 15022 HS code : 29161900 CAS : 24634615� Specifications appearance : White crystal granule Production Standard : FCCIV Content : 9801010 K2CO3 : 1 max Loss on drying : 1 max Chloride : 001 max Heavy metalsas : Pb 0001 max Packing in carton 25kgs net weight Quantity 14MT loaded into 1 x 20GP Excellent preservative properitesproperites Sorbic Acid Potassium Sorbate can restrain effectively the activity of mould yeast and aerophile bateria Restrain growth and reproduction of the pernicious micro organism as pseudomonas staphylococcus salmonella action to restrain growth is more powerful than killing Meanwhile it can not restrain useful microoranganim growth ad Anaerobicbearing barilli acidophil therefore to lengthen food store peroid and remain food original flavor The preservative efficiency of sorbic acid Potassium sorbate is 510 times sodium benzoate High safety Sorbic Acid Potassium Sorbate is one kind of nonsuturated fatty acid compounds It can be absorbed by human body rapidly then decomposed into CO2 and H2Omoreover no remaining in body ADI 025mgkg based on sorbic acid FAOWHO 1994 LD50 4920 mgkglarge mouse by mouth GRASFDA 1823640 1994 Its toxicity only 112 times table salts and 140 times sodium benzoate Good stability Sorbic Acid Potassium Sorbate is stable in sealed staus will not be decomposed until 270C It will be oxidized into colored ones and absorbing moisture in case exposed in air for a long time Wide application At the momentSorbic Acid Potassium Sorbate has been used extensively in food drinkvegetables in soy tabacco drugs cosmetics agricultural products forage and other domain Its applicaion should be wide and wide in the world As acidic preservative Sorbic Acid Potassium Sorbate is also used well in neutral foodph6065 The preservative efficiency of sodium benzoate will decrease clearly and have a bed taste while ph4 Applicaion flexibilitySorbic Acid Potassium Sorbate can be used by direct adding sprayingretting dry spraying using in packing material and other method
1. Main Features: 1) Good compatibility: It can be applicable to 80W laser tube. 2) Cutting Type and Sculpting Type: The cutting type has a good power stability and strong adaptability; while the sculpting type has a quick response speed and good engraving effect. 3) Dramatically lengthen the life of laser. 4) Easy Control: The start and stop of laser can be easily controlled by TTL level. And there are protection switch to test the external water, ventilation, etc. 5) Easy control of laser power: Both 0-5V analog signal and PWM signal can control the laser power. 6) The power supply possesses open circuit protection: Under the condition of good protective earthing, the power supply can work in open-circuit for a short time, which could avoid the damage of laser power supply because of the bursting of laser tube, thereby enhancing the life of power supply. 7) The power supply can take feedback interface which can be used in closed-loop control and testing the working current of laser. 8) The power supply adds a new function, that is timely scene judging which part is damaged, laser tube or laser power. 9) Application: Acrylic sculpture, cut; fabric sculpture, cut; Double-color plate engraving, cut; rubber sheet sculpture, cut, etc. 2. Specification: Input: Input Voltage: AC220V or AC110V to be specified when placing order AC frequency: 47440HZ Cold Surge Current: 60A(AC220V Input) 30A(AC110 Input) Current Leakage: 0.7mAAC220V Input :0.4mA(AC110V Input) Output: Maximum Input Voltage: DC 40KV Maximum Output Current: DC 28mA Efficiency: 90full load Mean Time Between Failure (MTBF): 10000H Response Speed: 1msfrom the switch Signal is given to the output current up to 90% of the setting current Control Interface: TTL level switch control; high or low effective level can be chosen (details refer to the control terminal specification) Withstand Voltage: Input-Output, Input-Shell: AC1500V 10mA 60S; Output negative is connected with machine shell. Protection: can work in open-circuit condition for a short time Require a good protective earthing and avoid arc between the positive and the machine shell Environment: Operating Temperature£º-10~40 Relative Humidity (RH)90©‡ Cooling Way: Force-Air Cooling (FAC) Dimension: LH=280*173*97(mm) COLOUR : YELLOW , BLACK 3.5kg to be boxed.
Product Features: 1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 1 Small size and light weight, Maintenance-free 2 Environmental protection and pollution-free materials, no heavy 3 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 4 Built-in BMS management system with comprehensive protection and monitoring control functions 5 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 6 Main control MCU can be centrally controlled and manage peripheral settings (AC charging module, inverter module, solar charging module) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
1 All-in-one design, high integration and space saving installation 2 Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years 3 Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability 4 Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage 5 BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range 6 CAN2.0 communication interface, has the advantages of strong real-time performance, long transmission distance, strong anti-electromagnetic interference ability 7 System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell 8 Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable; 9 Cell temperature management, can be automatically controlled with the air conditioner heater according to the cell condition to make the cell works at the most suitable temperature, and can be linked with the fire protection system as needed Performance characteristics 10 Accurately estimate the state of charge of the battery pack, that is, the remaining power of the battery, to ensure that the power of the battery pack is maintained within a reasonable range 11 Built-in BMS management system with comprehensive protection and monitoring control functions 12 5" LCD screen display, easy to operate, can check the temperature, voltage, working status, discharge current, dynamic and static SOC algorithm of a single cell, local display of alarm info, alarm level distinction, accurate positioning of abnormal cells 13 Main control MCU can be centrally controlled and manage peripheral settings (AC charger, inverter, solar charger) to adjust the charging current and voltage of peripheral devices according to the battery charging curve, making the system more reliable
1. Main Features: 1) Good compatibility: It can be applicable to 40W and 30W laser tube. 2) Fast response speed and effect. 3) Dramatically lengthen the life of laser. 4) Easy Control: The start and stop of laser can be easily controlled by TTL level. And there are protection switch to test the external water, ventilation, etc. 5) Easy control of laser power: Both 0-5V analog signal and PWM signal can control the laser power. 6) The power supply has open circuit protection: Under the condition of good protective earthing, the power supply can work in open-circuit for a short time, which could avoid the damage of laser power supply because of the bursting of laser tube, thereby enhancing the life of power supply. 7) The power supply can take feedback interface which can be used in closed-loop control and testing the working current of laser. 8) The power supply adds a new function, that is timely scene judging which part is damaged, laser tube or laser power. 9) Application: acrylic sculpture, cut; fabric sculpture, cut; rubber sheet sculpture, cut, etc. 2. Specification: Input: Input Voltage: AC220V or AC110V to be specified when placing order AC frequency: 47440HZ Cold Surge Current: 60A(AC220V Input) 30A(AC110 Input) Current Leakage: 0.7m AAC220V Input 0.4mA(AC110V Input) Output Maximum Input Voltage: DC 25KV Maximum Output Current: DC 20mA Efficiency: 90full load Mean Time Between Failure (MTBF): 10000H Response Speed: 1msfrom the switch Signal is given to the output current up to 90% of the setting current Control Interface: TTL level switch control; high or low effective level can be chosen (details refer to the control terminal specification) Withstand Voltage: Input-Output, Input-Shell: AC1500V 10mA 60S; Output negative is connected with machine shell. Protection: can work in open-circuit condition for a short time Require a good protective earthing and avoid arc between the positive and the machine shell Environment: Operating Temperature£º-10~40¡æ£¬Relative Humidity (RH)90©‡ Cooling Way: Force-Air Cooling (FAC) Dimension: LH=167*144*97(mm). 2.7kg,32*25*22cm carton box.
Van Aroma is one of the leading producers of Massoia Bark Oil (60 - 70% Lactone C10). Van Aroma is one of the biggest exporters in Indonesia. We produce and export Massoia Bark Oil (60 - 70% Lactone C10) from sustainable, and fully traceable sources. Extrait CO2 d'ecorce de massoia (60-70% lactone C10) / Extracto CO2 de corteza de Massoia (60-70% de lactona C10) / Minyak Kulit Masoi (60 - 70% Lakton C10) Olfactive Profile: Coconut, fruity, butter-like note, nutty CAS No: 85085-26-3 EC No: 285-357-2 FEMA No: 3747 INCI Name: Cryptocarya Massoy Bark Oil Product Synonyms: papua, scfe, supercritical fluid extraction, irian jaya, coconut, creamy, nutty, bark
Massoia Bark (Cryptocaria massoia) oil is being used in seasoning, traditional medicine and fragrance ingredient. C-10 Massoia lactone is a major constituent of its essential oil which has been proven as the antibacterial principle and has the ability to increase the phagocytic index of mice macrophage. In food industry, massoia bark CO2-extract is used to flavor food and beverages. Its sweet fragrance is reminiscent of coconut flavor. It is used for flavoring e.g. butter, milk and diary products, bakeries, confectionery, candies, ice cream, popcorn, cereals and dietary products. Massoia lactone has a pleasant odor which is described as sweet, coconutty, lactonic, creamy and milky. A concentration of 20-50 ppm gives products already a creamy, coconut, green, and slightly fruity taste. Minyak Kulit Masoi (50-60% Lakton C10) / Aceite esencial de corteza de Massoia (50-60% Lactona C10) / Huile Essentielle d corce de Massoia (50-60% Lactone C10) / (50-60% C10 / CAS No : 85085-26-3 EC No : 285-357-2 FEMA No : 3747 Olfactive Profile : Coconut, fruity, nutty, butter-like, creamy Product Synonyms : Massoia Bark Oil
The model Dw-co2-80w-9060-a Working area 900mm*600mm Laser power 80w Laser type Reci hermetic co2 glass tube Guide rails Taiwan imported linear guide rails Control system Dsp industrial control system Working table Aluminum platform Drive system Japan imported step motors Lens Imported focus lens and mirrors Positioning accuracy 0.01mm Cutting speed 1~1500mm/min Engraving speed 1~3000mm/min Cooling way Water cooling and production system Graphic format supported Bmp, gif, jpeg, dwg, psd, tiff, plt, cdr, dmg, Compatible software Coreldraw, photoshop, autocad Interface Usb Application computer system Windows 2000/windows xp/windows7 Cutting thickness 0-15mm(depends on different material) Optional Equipe with rotary device, industrail chiller cw3000 Worktable Electric up-down worktable max distance 500mm Applicable materials Non-metal materials such as acrylic, double color board, plexiglass, leahter, fabric, paper, hair felt.Carpet, Common glass, bamboo and wood, rubber, pvc, polypropylene, marble, granite and tiles, leather cloth etc. Applicable industries: Advertising industry, billboards, artistic gifts, crystal ornaments, paper-cut, bamboo, home design decorate industry, And wooden product, garment and leather, embroidery, decoration and upholster industry. Packing Plywood case Machine dimension L1450mm*w950mm*h1100mm Packing size 1680mm*1200mm*1250mm Net weight 210kg Gross weight 285kg
- Power: Solar street Light 40W; ( 30W, 50W, 60W, 70W, 80W, 100W,120W optional ) - Material: 6063 Die Casting Aluminum; - LED Brand: Sanan 5050, Lumen: 4800-5600 lumens; - Solar Panel: Monocrystalline Silicon 18V/60Wp; - Battery: Grade A Lithium Ion Battery 24Ah / 12.8V; - Installation Height: 6-7M, Installation Distance: 18-20M; - Rainy Day Time: 6-7 days, Working hour for 12 hours, Working Temperature: -20 C ~ 60 C ; - Certificate: IP65, CE, FCC, MSDS, ROHS.
General type 40W60W80W MYJG CO2 laser power supply myjg-40/60/80watt laser power source 1. Product Features: It has green color control signal terminal board 1. This laser power supply adopts zero current and half bridge soft switch circuit, it makes the power supply have high efficiency and quick response speed. Thus it is easy to match with CO2 laser tube made by any factories. 2. This laser power supply is easy to be controlled, it is suitable to High or Low level signal. The TTL level can control start or stop of laser output. While the power supply has emergency protection switch which can indicate water through and ventilation. 3. The laser output power can be adjusted by 0-5V analog signal or PWM signal. 4. This laser power supply has open cirsuit protection function. When protective earthing is good, the laser power supply can be in open circuit status during short time. This function can protect power supply when laser tube burst. 2. Aging test: Each laser power supply must pass this test which is taken at 60 degree centigrade for 12 hours in full load status. And the power supply must start and stop at each 7 seconds for 500 times. In this way we can ensure the laser power supply is qulified. 3. Specification: Item MYJG-40 MYJG-60 MYJG-80 MYJG-100 MYJG-130 MYJG-150 30KV 35KV 45KV 50KV 50KV 50KV 20mA 23mA 30mA 30mA 35mA 38mA Input AC Voltage AC220V or AC110V Input DC Voltage DC 300V or DC150V Input AC Frequency 47-440Hz Efficiency 91% Over Current Protection 130% of Max. Current Open Circuit Protection Yes (For short time) Cooling Fan Cooling Voltage Range of High Level Control Not Less Than3V Voltage Range of Low Level Control Not More Than0.8V Working Temperature -30 - +65 Degree Centigrade Humidity 20-85%RH(No Dew) Withstand Voltage Input-Output AC1500V/MinNot More Than10mA Input-Shell AC1500V/MinNot More Than10mA Output-Shell Connected Insulation Not Less Than 50MOHM(DC500V) Leakage Current Not Less Than 1mA(AC220V)Not More Than 0.5 mA(AC110V) Shock Resistance Amplitude: 0.5mm, Frequecy:10-55Hz, 3D Dretion:2 Hours MTBF Not Less Than30,000hours Full Load 60 Degree Centigrade test 12Hours 7 Seconds Start/Stop Test 500 Times Dimension(LXWXH)171mmx161mmx91mm Note Power supply warranty:12 months. Delivery time:2 working days after payment received. Package:Carton,foam and wooden box. Shipping method:DHL,UPS,Fedex or TNT Payment method: T/T,PAYPAL,Western Union Application:General type power supply and widely used on 40W-150W CO2 laser engraving machine.or cutting machine
The Duracell MX2500 AAAA battery is a type of cylindrical alkaline battery commonly used in various electronic devices that require a compact power source. AAAA batteries are smaller than AAA batteries and are often used in devices with slim designs or specific requirements. Duracell is a well-known brand in the battery industry, known for producing reliable and long-lasting batteries. The MX2500 AAAA battery is used in a range of devices such as stylus pens for tablets, medical devices, laser pointers, and more. It's important to note that AAAA batteries are less common than other battery sizes, so it's advisable to ensure compatibility before purchasing.
CO2 Laser Marking Machine CO2 Laser Marking Machine for sale custom Laser Marking Machine factory Why our CO2 laser marking machine more better Compact and portable structure Easy put into your trunk or your car boot Perfect Marking Performance Fiber source can use 30000 hours Working speed 5000-10000mm/s Field Lens from 110 to 600mm (different working area price different) High Speed scan head Red point : Clear the working path when it working. Control software : EZCAD Power consumption : 1-2 kw /H. Voltage AC220V10% ,50/60HZ or by customer need voltage. 5 years machine produce experience we have mastered the core technology of the Co2 laser marking machine. laser marking machine After-sale Service: 36 months guarantee of the whole machine, we will provide replacement or repair service when you need it. Software is on update for free whole life. English manual and CD video for machine using and maintaining will send to you with the machine. Our engineer can offer technical support in your country if necessary,or get train in our factory for free. 7*24h online technical support via Skype,Email,WhatsApp,Phone,Team Viewer,even on weekend even on vacation. Our CO2 laser marking machine has many advantages such as compact and portable structure, perfect marking performance and fiber source can use 30000 hours. What is Mainstream types of laser marking machines in 2020? They are fiber laser marking machine, 3d CO2 laser marking machine and semiconductor laser marking machine. For more information on precision laser cutting machine, please click here to browse our website.
It can be used for non-metal and thin metal processing. Widely used in advertising industry, handicraft industry, toys, clothing, construction, packaging, paper, etc. Applicable materials: stainless steel, carbon steel, acrylic, MDF board, clothing, leather, paper, etc. Working Size: 1300*900mm Laser Type : CO2 Laser Tube Laser Power : 150W/180W/280W/300W Control System: DSP Offline / USB Compatible Software : Autocad/Coreldraw/Photoshop Voltage : 220V/50Hz(110V/60Hz)
Co2 laser system treatment princple Co2 laser treatment using sealed-off co2 laser, wavelemgth 10600nm, the output invisible infrared laser beam is characterized by small, high energy density; laser beam output by the focusing mirror, the point of the target tissue can Power to tissue >15w Focal spot diameter
Catalytic co2 laser tube 1200*80 80w 9months 1400*80 100w 9months 1600*80 150w 9months Improved co2 laser tube 1600*60 80w 3months 1600*80 100w 6months Traditionalco2 laser tube 1200*60 60w 3months 1250*60 60w 3months
Technical parameters (the working area and laser power can be customized according to requirement) Model of machine CX-CO2-30/60/80/100(optional) Laser tube Co2 laser tube Cutting area110mm 110mm /300mm 300mm(optional) Laser power 30w/60w/80w /100w(optional) Marking speed0-7000mm/s Operating voltage Ac220v 10%, 50hz Location precision 0.01mm Working environmentTemperature humidity 0-95% Min. Line width0.015mm Min. Character0.3mm Graphic format supportedBmp, HPGL(PLT), JPEG, GIF, TIFF, PCX, TAG, CDR, DWG, DXF, COMPATIBLE HPG ORDER, SUPPORT DXF, PLT, BMP and dxt(tiandao embroider software), etc. Marking depth 0.01-0.2mm Working tableLift platform up to 1, 000mm from the bottom to the top Auxiliary devic eExhaust fan and cooling system Laser wavelength1064nm. Wooden case
Applying imported american co2 radio frequency laser and high-speed scanning lens system, collocated with high qualified optic components, stable laser electrical source and full auto-controlling system, produces precise, reliable and fast performance and long time's continuous running as well, it can be directly applied to mass manufacturing streamlines. Different powers ranging from 10 - 350w
1.Introduction The laser marking machine YMM-10C is applicable to almost any non-metal surface. It has many clear advantages with comparison to traditional marking methods, such as noise-free, stress-free, ink-free, hazard-free (Printing marking uses hazardous solvent handling and disposal), tools-free and wearing-free (Tools wear in stamping systems). Laser marking offers a quiet, clean, low maintenance and easily configured system for permanent marking of almost any surface. 2. Features Unique optics design Friendly and ergonomical man-machine interface Stable, precise and high-speed File format to support any CorelDraw format, e.g., PLT, BMP, DST, etc.. Embedded test and graphic design tools offers various editing features Barcode marking including Code 39, 93, 128, EAN-8, EAN-13, VIN, Data Matrix, QR Code, etc. , and serial numbers 3. Technical Parameters Wavelength 1064 nm Aiming laser Red Linear speed Adjustable, max 5000 mm/ s Line width Min 0.2 mm Letter size Min 0.8 mm Marking area F=160 mm 70 mm í- 70 mm F=220 mm 100 mm í- 100 mm F=250 mm 150 mm í-150 mm Power supply Single-phase AC 220 V í+ 10%, 50 Hz / 60Hz Input power Max 210W Dimension 550 mm x 290 mm x 650 mm Net weight ~33.75 kg Cooling Mode Air cooling 4.Standard Configuration Laser machine í- 1 set PC í- 1 set Marking software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case