1.Introduction The new generation of laser scribing machine YMS-50 (CE certificated product) is capable of scribing various silicon wafer, solar cell, ceramic wafer, thin metal sheet (~0.5 mm thick maximum), etc., in industries of electronics, semiconductor and solar energy, etc.. It is designed by experts with professional features, such as excellent beam quality and power stability, precise CNC worktable and efficient auto cooling system. Some of the most important parts are manufactured in UK, USA and Germany. Thanks to the automatic control of the whole system, you can save more efforts on the manufacturing, instead of how to operate and maintain the system. 2. Features Excellent beam quality and system reliability High-speed scribing (up to 120 mm/s), very low-defective index Auto cooling system Precise CNC worktable Friendly man-machine interface and simple software operation 3. Technical Parameters Laser medium Nd3+:YAG Wavelength 1064 nm Pump source Kr lamp Laser cavity Ceramic Modulated frequency 0.5 - 50 kHz Beam power Adjustable, max 50 W Aiming laser Red Scribing speed Adjustable, max 120 mm/ s Scribing depth Max 1.2mm Line width Min 0.2mm Worktable repeating accuracy 0.01mm Marking area 300 mm í- 300 mm Power supply 3-phase 4-wire AC 380V í+ 10%,50 Hz /60 Hz,PE,(A voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 5kW Dimension 550 mm x 290 mm x 650 mm Net weight ~560 kg Cooling Mode Water cooling 4.Standard Configuration Laser machine í- 1 set Exhauster í- 1 set Vacuum pump í- 1 set Cooling unit (Chiller, temperature controller, water tank, filter) í- 1 set Worktable unit (CNC controller) í- 1 set Kr lamp í- 2 pieces Laser detector í- 1 piece PC í- 1 set Scribing software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case
1.Introduction The new generation of laser marking machine YMM-50 is applicable to almost any material surface. It offers various advantages with comparison to the traditional marking methods, such as noise-free, stress-free, ink-free, hazard-free (Printing marking uses hazardous solvent handling and disposal), tools-free and wearing-free(Tools wear in stamping systems). Laser marking technique offers a quiet, clean, low maintenance and easily configured system for permanent marking of almost any material surface. 2. Features Friendly and ergonomical man-machine interface Stable, precise and high-speed system File format to support any CorelDraw format, e.g., PLT, BMP, DST, etc.; Embedded test and graphic design tools offer various editing features Auto-numbering Barcode marking including Code 39, 93, 128, EAN-8, EAN-13, VIN, etc. and serial numbers Auto cooling Flexible text / graphics marking; Line or arc scribing to enable flexible profile scribing (Complicated profile scribing is optional) 3. Technical Parameters Wavelength 1064 nm Pump source Kr lamp Laser cavity Ceramic Laser output stability í_ í+ 3% Beam expanded angle í_ 8 mrad Aiming laser Red Linear speed Adjustable, max 5000 mm/ s Line width Min 0.1mm Letter size Min 0.5mm Marking area F=160 mm 70 mm í- 70 mm F=220 mm 100 mm í- 100 mm F=250 mm 150 mm í-150 mm Power supply Single-phase AC 220 V í+ 10%, 50 Hz /60 Hz,PE,(A voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 7kW Dimension 1500 mm x 500 mm x 1200 mm Net weight ~180 kg Cooling Mode Water cooling 4.Standard Configuration Laser machine í- 1 set PC í- 1 set Marking software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case
1.Introduction The laser marking machine YMM-10C is applicable to almost any non-metal surface. It has many clear advantages with comparison to traditional marking methods, such as noise-free, stress-free, ink-free, hazard-free (Printing marking uses hazardous solvent handling and disposal), tools-free and wearing-free (Tools wear in stamping systems). Laser marking offers a quiet, clean, low maintenance and easily configured system for permanent marking of almost any surface. 2. Features Unique optics design Friendly and ergonomical man-machine interface Stable, precise and high-speed File format to support any CorelDraw format, e.g., PLT, BMP, DST, etc.. Embedded test and graphic design tools offers various editing features Barcode marking including Code 39, 93, 128, EAN-8, EAN-13, VIN, Data Matrix, QR Code, etc. , and serial numbers 3. Technical Parameters Wavelength 1064 nm Aiming laser Red Linear speed Adjustable, max 5000 mm/ s Line width Min 0.2 mm Letter size Min 0.8 mm Marking area F=160 mm 70 mm í- 70 mm F=220 mm 100 mm í- 100 mm F=250 mm 150 mm í-150 mm Power supply Single-phase AC 220 V í+ 10%, 50 Hz / 60Hz Input power Max 210W Dimension 550 mm x 290 mm x 650 mm Net weight ~33.75 kg Cooling Mode Air cooling 4.Standard Configuration Laser machine í- 1 set PC í- 1 set Marking software (In English) í- 1 set Operation manual (In English) í- 1 Wooden Case
1.Introduction The laser scribing machine is specially designed for insulation of a-si (amorphous silicon) and back contacts such as aluminum coating of the a-si thin-film solar cell, without any damage to tco (transparent conductive oxidization) coating. 2. Features Cnc worktable size: 900mm íß 1600mm High-speed up to 500 mm/s or 200 íß 4 Auto programming / cooling / on-off Kerfs width 0.05 ¿c 0.15 mm, continuously adjustable 3. Technical parameters Wavelength 532 nm Laser output stability ín ía 3% Beam expanded angle ín 8 mrad Scribing speed Continuously adjustable, max 250mm/s Kerf width Continuously adjustable, 0.05 - 0.15 mm Scribing area 900 mm íß 1600 mm Power supply Single-phase ac 220v ía 10%, 50 hz /60 hz, pe, (a voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 1500w Cooling mode Air cooling 4.Standard configuration Laser machine íß 1 set Worktable unit (cnc controller) íß 1 set Pc íß 1 set Scribing software (in english) íß 1 set Operation manual (in english) íß 1. Wooden case
1.Introduction The laser scribing machine is specially designed for insulation of a-si (amorphous silicon) and back contacts such as aluminum coating of the a-si thin-film solar cell, without any damage to tco (transparent conductive oxidization) coating. 2. Features Laser: lamp-pumping laser Cnc worktable size: 500mm íß 500mm High-speed up to250 mm/s Auto programming / cooling / on-off Kerfs width 0.05-0.15 mm, continuously adjustable 3. Technical parameters Wavelength 532 nm Pump source Kr lamp Laser output stability ín ía 3% Beam expanded angle ín 8 mrad Scribing speed Continuously adjustable, max 250mm/s Kerf width Continuously adjustable, 0.05 ~ 0.15 mm Scribing area 500 mm íß 500 mm Power supply 3-phase 4-wire ac 380v ía 10%, 50 hz /60 hz, pe, (a voltage stabilizer might be required to avoid irregular cutting quality caused by severe voltage fluctuation) Input power Max 5kw Cooling mode Water cooling 4.Standard configuration Laser machine íß 1 set Exhauster íß 1 set Vacuum pump íß 1 set Cooling unit (chiller, temperature controller, water tank, filter) íß 1 set Worktable unit (cnc controller) íß 1 set Kr lamp íß 2 pieces Laser detector íß 1 piece Wooden case
The UV laser marking machine is developed by using a 355nm UV laser. This machine uses a third-order intracavity frequency doubling technology. Compared with infrared lasers, the 355nm UV laser has a very small spot, and the marking effect is directly interrupted by a short-wavelength laser. The molecular chain greatly reduces the mechanical deformation of the material. Thermal deformation (cold light), because it is mainly used for ultra-fine marking and engraving. It is especially suitable for applications such as marking, micro-hole drilling of food and pharmaceutical packaging materials, high-speed dicing of glass materials, and complex pattern cutting of silicon wafers.
This co2 laser cutting machine can use for engraving and cutting nonmetal materials. Applicable Materials Glass, organic glass, leather, cloth, acrylic, wood, MDF, PVC, plywood, maple leaf, double-color sheet, bamboo, Plexiglas, paper, leather, marble, ceramics etc. nonmetal materials. Applicable Industries Advertisement, arts and crafts, leather, toys, garments, model, building upholstery, computerized embroidery and clipping, packaging and paper industry. Our Services Rather careful and professional packing way for machine protection. 1 - Film. Put PE film on the machine and some spare parts, then put bubble wrap to the machine. 2 - Free-fumigation wooden case with steel tube support on wooden cover. The humidity-proof paper above the wooden plate. This kind of package could protect the machine very well from dust and humidity etc.
It can realized automatic edition and correction of characters, signs, graphs, images, bar codes, two-dimensional codes, automatically increased serial numbers. It can support various file formats like PLT, PCX, DXP, BMP, JPG, and so on. It may use TIF fonts directly. 24-hour non-stop running makes it meet the demand of massive on-line and off-line industrialized production.