LC 104 is an ideal single product boiler internal treatment, specially formulated by blending sludge conditioner & oxygen scavenger for dual function in packaged boiler systems. It can control not only calcium carbonate & calcium phosphate deposits but also calcium sulfate and barium sulfate. Highly concentrated alkaline product. Eliminates excessive precipitation of solids and reduces sludge accumulation. The oxygen scavenger prevents pitting corrosion in the boiler system. It is environmentally safe, non-hazardous and non-corrosive. Application Used in packaged boilers below 5 Tons/Hr. For use with make-up water hardness below 150 ppm and effectively disperses iron oxides as well as calcium phosphate and clay. Injected directly into the boiler by means of a proportioning pump. Dosage Initial : 2 quarts per 100 gallons or 1 : 200 ratio Maintenance: 1 quart for every 100 gallons of make-up water or 1 : 400 ratio Maintain 15-25 ppm (mg/l) of orthophosphate in the boiler waters with pH between 11.0 – 12.0. Maintain Conductivity below 3000 µmho/cm. Consult LifeChem Technical Services when Hardness is low or high. Handling & Precaution LC 104 is an alkaline product and should be handled with care to prevent personal injury. Wear protective clothing and eye protection. In case of contact with skin, immediately flush with water. In case of contact with eye, flush with water for 15 minutes and obtain immediate medical attention. Triple rinse used cans before reuse or disposal. Refer to MSDS for detailed information. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 232 is a very strong concentrated descaler, specifically designed to remove silica based scales and other stubborn scales. It is a special blend of volatile acids, corrosion inhibitors & dispersing agents. It effectively removes stubborn silica scale and soil of silicate/phosphate nature from metal and other surfaces. LC 232 is an excellent additive for the LC 231 & LC 233 for additional effectiveness against silica based scales and effectively bring down cost by reducing the amount of other descalers. Its special formulation dissolves scale and rust deep down with the selective inhibitors protecting metal surfaces. Application Spray or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC 232. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat and then flush off with water. Flush with water until all scale is removed. Add with other descaler like LC 231 & LC 233 for stubborn and difficult to remove scales. For best results use circulation or dipping method use of passivating agent like LC 252 or LC 253 is essential. Make test strip before use. NOT TO BE USED ON GLASS/SILICATE BASED SURFACES. Dosage Dilute one part of LC 232 with up to 10 parts of water or depending on the thickness of scales. Handling & Precaution Irritating to eyes and skin. Protective clothing and eye protection should be provided and worn. After contact with skin, wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 233 is a special blend of non-volatile acids, corrosion inhibitors, emulsifiers & dispersing agents. Effectively removes rust, scale and soil from metal and concrete surfaces. Application May be sprayed or brushed on surfaces. Clean surface free from rust, soil and dirt. Apply LC 233. Allow to stand for 10 - 20 minutes, then wipe off with water. Dry surface can be repainted if desired for longer protection Dosage For descaling of condensers, dilute one part of LC 233 with upto 10 parts of water depending on the thickness of scales. Allow to stand for several hours. Flush with water until all scale are removed from condensers. Handling & Precaution Irritating to eyes and skin. After contact with skin wash immediately with plenty of water. In case of eye contact irrigate thoroughly with water for at least 15 minutes. Seek medical advice. Packaging Available in pail of 20 lt.. Can also be custom packaged.
LC 200A is safe, phosphatic alumunium cleaner and brightener. It’s strong formula will dissolve any oxide layer and also has the added benefit of providing a protective phosphatic layer to keep aluminum surfaces looking at their best. The non-toxic formulation also prevents further oxidation of the surface and repels dust build up owing to its electrostatic effect. It has penetrating agents that clings to alumunium surfaces for maximum effective cleaning result. Application Use LC 200A undiluted for initial cleaning and brightening on tough or built-up soil problem. Use diluted product for regular cleaning. Determine dilution depending on contamination type & frequency of cleaning. For on-going maintenance use LC 301 for a protective and shiny coat. For maximum cleaning, apply LC 200A with a highpressure washer Dosage The dilution will vary, depending on the condition on the surface to be cleaned. For best result, rinse with a high-pressure washer or apply with a brush. For normal cleaning & brightening; apply LC 200A at a dilution up to 1:20 with water. Allow the solution to react with the surface for 1 – 3 minutes, and then rinse thoroughly with clean water through a pressure washer. Do not allow LC 200A to dry on the surface. Repeat application if necessary. Handling & Precaution Contains mild acid. Do not ingest. Do not get in eyes or clothing. Wear a face shield, neoprene rubber gloves & protective clothing if spattering is expected. Keep the container closed when not in use. Avoid breathing the mists if produced during application by spraying. Use sufficient ventilation to prevent build-up of mists during application. Packaging Available in pail of 20 lt. Can also be custom packaged.
Lc 219 is a technical specialty cleaner designed to remove difficult deposits & residue on glass surfaces arrising from long exposure to external weather Conditions. The stains & marks, including dried fungus generally builds up on Exposed glass surfaces can easily be removed using lifechem’s lc 219. It Is a technical product & requires complete attention to the “guidelines on Application” during it’s use. Lc 219 effectively removes the stains & deposits Which is generally not removed by standard glass cleaners. It leaves glass Sparkling clean, smear-free. The anti static components repel tiny dust particles and thus reduces Deposits efficiently. Use lifechem’s lc 203 ; glass cleaner regularly to keep Your glass surface in a sprkling condition. Application 1. Use undiluted or diluted product as required depending on the stains & Deposits. A small test patch must be made to select dilution. 2. Damp a piece of clean white wiping cloth with lc 219 and squeeze out any Extra liquid to avoid spreading & flowing during wiping. 3. Spread a this layer using the damp/wet cloth on the stained glass or mirror Surface. Select only a small area depending on drying rate. 4. Wipe-off using a separate piece of clean, white cloth to a shining lusture. A Soaking time may be required in some cases. 5. Use lc 203 to rinse the cleaned surface using glass-wiper in the usual Method. 6. Leave it to dry. 7. Repeat if necessary for highly soiled stains, deposits etc. 8. Never be used on coated glass unless proved to be safe after testing. Dosage May be used undiluted or may be diluted to suit method of application and extent Of contamination. Suggested dilution is 2:1 or 1:1. Use clean & softened Water only. Un attended application may result into damage. Handling & precaution Avoid spill & stains of lc 219 on ceramic tiles, glass as prolonged exposure to Lc 219 direct effect. Keep away from children. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 270 is a water based general purpose cleaner to Penetrate, emulsify and disperse oil, grease, dirt and Grime and other types of soils from a variety of hard Surfaces. Ideal for cleaning walls, floors, desks, light Fixtures, automobiles, painted woodwork. Also can be Used on metal surfaces such as stainless steel, Aluminum, cooper and brass. Application Spray, mop, brush wipe, dip method are recommended. Use for Cleaning walls, floors, desks, light fixtures, automobile, painted Wood work. Dosage Dilute with ratio of 1 : 10 with water depending on the dirt Thickness Handling & precaution Avoid spills on eyes. Should avoid unnecessary contact with Skin. Can irritate when exposed for a longer period. Harmful if Swallowed. Packaging Available in pail of 20 lt. Can also be custom packaged.
Lc 300 is a designed specifically for stains on granite Surfaces arising out of contamination during production Or due to storage. It is very effective for stains on granite Surfaces due to poor quality water, inproper storage & Soil contamination. It is an acid based special blend of Selected penetrants, emulsifiers, dispersant & solvent Carriers designed to effectively penetrate, react, dissolve & remove the stains from the surfaces as well as deeper Into the granite structure without affecting the surface. Application Make sure that the granite surfaces are free from dust, soil & dirt. Apply lc 300 on The pre-treated surface by brushing to leave a thin uniform film on the whole Surface. Do not leave any surface untreated. Wait until 15-30 minutes or more until The stains start dispersing. Rinse and wipe clean the whole surface with demin Water. For deeper & thicker stains, repeat the process. May not be suitable for Certain types of granite & marble. Always make a test sample before final Application. Handling & precaution Avoid contact with eyes, skin and clothing. In case of contact, immediately wash With plenty of water. Harmful if swallowed. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Multi type glass cleaner
Kb 208 can be used to remove stains from hard surfaces Including metallic and non-metallic surfaces like glass, ceramic, Melamine, etc. The key to an effective cleaning depend on proper Dilution & soaking time. It’s food-grade quality allows its use in Places where cleaned surfaces may have direct contact with food. Kb 208 is designed specially for use in places where the use of Acidic products are not recommended. It’s strong disinfectant Function kills most common microbes & disease causing bacteria. Application Kb 208 must be diluted with water for soaking, dipping etc. May also be used by Brushing & scrapping. Dilution depend on soak time, for faster action use lower Dilution ratio that is higher concentration. May be diluted up to 500 times or more. It Has disinfectant function. Dosage Add about 100 gm/100 ml of kb 208 to about 100 lt. Of water or as required for Soaking and dipping. Use higher concentration for faster action and tougher stains. Agitation gives better result. Re-use solution until turbidity is high. Required to Repeat the process if necessary. When the cleaning process is complete, flush with Clean water. Use concentrated product for manual cleaning Handling & precaution This product is alkaline and should be handled with care to prevent personal injury. Avoid prolonged skin contact and breathing of the fumes. Refer to material safety Data sheet for more specific procedures and directions. Discoloration may Result when contact with colored clothing. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Cleaning vinyl surfaces from dirt, grease, oil, and dust. Suitable for carpet cleaning vinyl flooring and other vinyl surfaces. Safe to use on metal surfaces such as stainless steelm aluminum, copper, brass.
Lc 121 is specially formulated for large installations and High hardness water. It is developed for effective, Economical cooling tower treatment at hospitals, hotels, Large apartment houses, office buildings and other Industrial and institutional cooling installations. Also Recommended for a small installations with high Hardness make-up water. It contains no phosphates, Chromate, zinc or other chemicals that cause pollution Problem. Helps control mineral deposits, sludge and Surface pitting and does not stain automobiles or Buildings. Application Use a reliable automatic proportioner with timer for controlled dosage. Directly inject in to the circulating pipe upstream from the condenser. Cycles Of concentration will vary from 5 – 20 as a probable upper limit. For higher Limits consult our laboratory. Dosage Initial treatment : add 1 gallon of lc 121 per 2, 000 gallons of re-circulating Water. Maintenance treatment : 1 gallon per 6, 000 gallons of water lost to Bleed off. Handling & precaution Wear protective clothing and eye protection should be worn. In case of skin Contact, immediately flush thoroughly with plenty of clean water. In case of Eye contact, flush with copious of amounts of water for 15 minutes and Obtain immediate medical attention. Refer to msds for more specific Directions. Packaging Available in pail of 20 lt.. Can also be custom packaged
Lc 126 condenser water treatment does not use sodium Chromate, zinc or other toxic chemicals in its composition. It Eliminates the serious pollution problems usually associated With the use of such chemicals for corrosion and scale Control in cooling system. It protects medium size cooling Towers against scale, sludge and corrosion. Lc 126 Contains a special anti-foulant additive to reduce Accumulations of mud and silt in condenser tubes. Ideal for Average towers with 75 to 500 ton capacity. Application Formulated for use in open re-circulating cooling water systems found in air Conditioning and process operations. Apply manually, directly to the cooling Tower basin. Dosage Initial dosage : add 1 gallon of lc 126 for every 500 gallons of system Capacity. Maintenance dosage : add 1 gallon of lc 126 for every 1, 000 gallons of System water lost to bleed off from the cooling tower system Handling & precaution Slightly alkaline aqueous solution. Keep out of reach of children. Refer to Material safety data sheet for more specific procedures and directions. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 141 is single product treatment designed to prevent Scale deposits and corrosion to ferrous and non-ferrous Surfaces in hot water heating systems and chilled closed Loops. It passivates the surfaces and forms a barrier layer to Inhibit corrosion. It is a synergistic combination of Phosphonates, polymers and phosphate. Application Easily feed/injected directly into the system by means of a chemical by Pass feeder. Dosage Initial treatment is 1 gallon per 1, 000 gallons of water in the system. There After add lc 141 to maintain a level of 25-35 ppm (mg/l) of Orthophosphate. Handling & precaution It is highly alkaline and should be handled with care to prevent personal Injury. Protective clothing and eye protection should be provided and worn. In case of skin contact , immediately flush thoroughly with plenty of clean Water. In case of eye contact, flush with copious amounts of water for 15 Minutes and obtain immediate medical attention. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 144 is formulated to prevent and reduce scale, Rust, corrosion and sludge in generator system. It is The most effective coolant for generator and other High temperature systems. Lc 144 is a special blend Of selective glycols, anti-corrosion additives and Sludge conditioners that provide smooth running of The systems. Application Lc 144 is widely used in power plants, generator system, etc... Found in Marines, aviations, industries, automotives, industries, hospitals, etc. Benefits ? excellent protection ? no more severe Damages ? non-flammable ? non-polluting ? non-corrosive ? non-toxic ? completely safe to Use ? reduces costly Maintenance Dosages 1. Check incoming water source for total hardness and chloride. 2. Recommended total hardness below 30 ppm and chloride below 50 Ppm. 3. Lc 144 can be diluted at a ratio of 1:1, 1:5, 1;10, 1:32 with deionised Water (recommended). 4. Repeat application monthly or quarterly depending on application. Flush if colour changes or becomes cloudy. Handling & precaution For professional use only. To be used in well ventilated environment. In Case of contact with eyes, rinse thoroughly with water and seek medical Advice immediately. If swallowed, take plenty of water and seek medical Advice immediately. Avoid prolonged contact with skin. Put on gloves for Sensitive skin. Keep out of reach of children. Additional information may Be obtained from material safety data sheet (msds). Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 238 is designed specially for use in systems where the use Of concentrated acidic or concentrated alkaline descalers are Not recommended. This product is specially formulated for Specific cleaning and descaling purposes for sensitive system. Lc 238 may be re-circulated by means of a high volume pump For the removal of scale. Lc 238 can be used safely on to Copper & brass surfaces besides being very effective in steel System. This product contains organic poly acrylic & polymer Compound. Application Lc 238 may be soaked overnight and re-circulated. When scale is Present, the tubes should first scraped out to remove as much as possible And then flushed out with a hose. Dosage Circulate an appropriate concentrated solution based on the scale and Corrosion. For storing / stand by system use lc 253 or lc 252. For more Detail and specific method and concentration, please consult lifechem Technical services. Handling & precaution This product ph is between 4.0 – 9.0 and should be handled with care to Prevent personal injury. Protective clothing, gloves and eye protection Should be worn. In case of skin contact, immediately flush thoroughly with Plenty of clean water. In case of eye contact, flush with copious amounts Of water for 15 minutes and consult a physician. Refer to material safety Data sheet for more specific procedures and directions. Packaging Available in pail of 20 lt.. Can also be custom packaged .
Lc 240 is a highly alkaline concentrated product designed For neutralizing the metal surfaces that is susceptible to Corrosion. Lc 240 consists of a blend of soluble carbonate, Hydroxide and corrosion inhibitors. It is designed to control Corrosion and neutralize any acid left from “acid cleaning” Processes. It contains no chromate or heavy metals. It is Food grade, user & machine friendly and environmentally Safe. Neutralized mixtures can safely be disposed into Sewers. [ p – powder / l – liquid ] Application Can be added directly into the liquid volume to give a 1% to 5% solution or add till Ph value is between 6 - 8, which then may be used for neutralization & protection. For offline storing purposes a 0.5% solution may be quite effective. The surface to Be neutralized or get protection must receive a minimum of 5-10 minute contact Time. Dosage Dosage is calculated depending on the circulating or storing volume and the time Of contact. A diluted solution of 0.5% up to 5% is recommended. Use concentrated Solution for less contact time & higher initial conditions, where as a 0.5% solution May be used for storing. Ensure ph value between 6 – 8 before disposal. Handling & precaution This product is quite alkaline and should be handled with care to prevent personal Injury. Protective clothing and eye protection should be provided and worn. In case Of skin contact, immediately flush thoroughly with plenty of clean water. In case of Eye contact, flush with copious of amounts of water for 15 minutes and obtain Immediate medical attention. Packaging Available in pail of 20 lt. Can also be custom packaged.
Lc 214 is a special blend of penetrants, chlorinated Solvents, surfactants and emulsifiers designed to easily And quickly strip paint and varnish from metals, concrete, Brick, wood and most hard surfaces. The deep penetrating action of lc 214 soften though Paint and removes it without scraping. Lc 214 is homogeneous which adheres to vertical and Inverted surfaces and activate paint coating quickly. Application Brush, wipe or apply a heavy coat of lc 214 on the area to be Treated. For the reaction to be completed, allow lc 214 to Remain until old paint bubbles or wrinkles. Flush with water or Remove with scrapper. More than one application may be Required for areas of very heavy paint build-up. Dosage One ( 1 ) liter of lc 214 can be used over an area of 3 – 5 m2 . Handling & precaution Avoid contact with skin. In case of contact, wash affected areas With water. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lifting rust on surface of iron, metal, etc.
Lc 252 is designed to be used for “passivating” open & Closed loop systems to prevent corrosion. It is a liquid blend Of nitrite and other corrosion preventives which protects not Only steel surfaces but also copper and other metal as well. The high concentration makes it a cost effective nitrite based Passivating agent with the added advantage of being multimetal Compatibility and thus do not require separation of Non-ferrous parts from a system during passivation. Application Normally injected into the system that is previously filled with standard industrial Grade water and circulated continuously under required pressure for about 1-2 Hours with hourly monitoring of the nitrite concention. A higher temperature help to Accelerate the passivating process and therefore reduce operation time. An Appropriate temperature suitable to the system and available resources is choosen Between 35 – 950c Dosage Initial : 1 : 400 is suitable in most cases of passivation processes operating at Optimum temperature between 50 – 700c. Depending on the quality of water used Some adjustment in the amount may be required to maintain the ph of the solution. An increase in concentration of lc 252 is necessary in badly soiled systems. Additional amount of lc 252 may be required to be added during the circulation for The passivation process in order to maintain the required control parameters while Monitoring. Handling & precaution Avoid contact with acid, ammonium salts and activated carbon. No respiratory Protection. Is required, however, maintain adequate ventilation. Use rubber gloves And safety goggles when handling. Packaging Available in pail of 20 lt.. Can also be custom packaged.
Lc 271 is a strong solvent based degreaser and Decarboniser for the rapid removal of oil, grease, paint, Adhesives and waxes from metal components and Machinery. The mechanism of cleaning involves a quick Penetration of lc 271 to soften polymerized oils Associated with the carbon deposit. Then the deposit is Loosened and easily dispersed into the solvent. The Powerful solvents act quickly to break the bond between The deposits and the metal surface. Lc 271 is safe to Use on ferrous and non-ferrous metals, concrete and Ceramics. Application Ideal to use in metal dip tanks, spraying, wiping etc. Item to be descaled, Decarbonised or degreased should be immersed below the surface. Loose Soiling should be removed prior to immersion. After removal allow them to Drain for 10 minutes. Then, rinse with low pressure water. Keep container Covered for control evaporation. Handling & precaution Harmful if inhaled. May cause burns to eyes and skin. In case of contact With skin, wash immediately with plenty of water. Ensure adequate Ventilation at the point of use. If swallowed, seek medical attention. Packaging Available in pail of 20 lt.. Can also be custom packaged.
