DESCRIPTION: Commercial rubber sheet used for gasket & packing purpose in industrial applications. These sheets / rolls are made from Prime polymer blended with reclaim rubber. As it is cured using compression moulding & rotary drum curing system available in smooth & cloth impression finish with or without choice of insertion. APPLICATIONS: This commercial rubber sheets / rolls are mainly used for flange gasket packing to avoid leakages from air, water & inorganic chemicals, machinery packing pads, anti vibration pads & flooring purpose. PROPERTY: Good resistance to inorganic chemicals, water, air & heat up to 70°C. Poor resistance to Ozone, UV, Sunlight, oil & solvents & organic chemicals. Boron Rubbers India has custom designed this rubber to meet many applications on several different levels while maintaining a very economical basis for a rubber sheets / rolls. COLOR: Black No GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Elongation (%) 1 BRZ – 1560 1.50 70 25 200 2 BRZ – 1665 1.60 65 20 175 3 BRZ – 1870 1.80 60 15 150 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 STORAGE OF PRODUCTS Do not expose rubber sheet to direct sunlight, sheets away from heat source, preferably in dark, air ventilated room will help give longer life & optimum properties Do not remove polythene packing before use to prevent it from exposure of atmospheric oxygen, ozone & polluted air. Do not store rubber sheet rolls in open, even after covering it with tarpaulin to protect from air & rain. Always keep rolls in vertical position ONLY Keep rolls away from solvent, oil & fuel storage. Do not use hooks while loading/unloading the rolls. Inspect sheet for smooth surface & hardness (with rubber hardness tester).
DESCRIPTION: NR / SBR blend rubber sheets / rolls are used in the commercial and industrial applications. This specifically designed rubber material is long-¬lasting that is suitable for operational use which provides excellent mechanical properties like high resilience, low compression set, high resistance to cut, tear & abrasion & also offers resistance to many acids, alkalis & salts. The operation temperature range is (-¬20°C to +80°C). It is available in wide range of hardness from 40 Shore A to 80 Shore A. It has very good physical properties like Tensile strength, wear & tears properties, Abrasion resistance. APPLICATIONS: NR / SBR Rubber sheets / rolls are used for wide range of applications like skirt board, bridge bearing, gasket for high pressure packing, heavy weight machinery packing, Para-¬quality for sand/shot blasting machinery & used as shock absorber. NR / SBR Rubber sheets/rolls can be used as shelf liner; workstation table liner and work area rubber lining that can with and moderate chemicals & alkaline solutions. These sheets can also be used for anti-abrasion lining for material handling machinery in mines alike industries PROPERTY: Excellent resistance to inorganic chemicals, water, air & heat up to 80°C. Poor resistance to Ozone, UV, Sunlight, oil & solvents & organic chemicals. NO. GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Elongation (%) 1 BNS-1240 1.20 40 80 600 2 BNS-1345 1.30 45 90 500 3 BNS-1450 1.40 50 70 450 4 BNS-1565 1.50 65 60 400 5 BNS-1670 1.60 70 50 300 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 STORAGE OF PRODUCTS Do not expose rubber sheet to direct sunlight, sheets away from heat source, preferably in dark, air ventilated room will help give longer life & optimum properties Do not remove polythene packing before use to prevent it from exposure of atmospheric oxygen, ozone & polluted air. Do not store rubber sheet rolls in open, even after covering it with tarpaulin to protect from air & rain. Always keep rolls in vertical position ONLY Keep rolls away from solvent, oil & fuel storage. Do not use hooks while loading/unloading the rolls. Inspect sheet for smooth surface & hardness (with rubber hardness tester)
DESCRIPTION: Commercial Grade Neoprene rubber blended with natural rubber is a general-purpose sheet for most commercial applications. This grade of rubber is used as a barrier or gasket material and can also be used inside rooms for sandblasting and impact resistance for industrial needs. Commercial Grade Neoprene rubber sheet / roll are moderately resistance to oil, sunlight, ozone and oxidation material providing abrasion resistance, repeated flexing applications, wide temperature range (excellent cold temperature flexibility) and has a physical toughness. APPLICATIONS: Wear resistant pads, vibration pads, isolation mounts, buffers, diaphragms, industrial matting, water retaining structures and in industrial applications such as gaskets, corrosion-¬resistant coatings. For more information click here. COMMERCIAL GRADE NEOPRENE RUBBER SHEET NO GRADES NEOPRENE (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNPNR-15 15 1.65 65 20 150 2 BNPNR-30 30 1.60 65 30 200 3 BNPNR-50 50 1.55 65 40 200 4 BNPNR-70 70 1.50 65 50 250 PROPERTY: General purpose sheets / rolls resist moderate oil & heat resistance, fungus resistance, flame retardancy, acid & alkali resistance, sunlight aging & heat resistance up to 100°C. Best quality for sealing gasket, packing, mounting pad, machinery packing, manhole packing, as a mechanical applications without confect any fuel & also useful in marine parts due to good ozone resistance. PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with hydrocarbons, solvents, acids & alkalies. To maintain the sheet/roll in optimum condition they should be stored in cool and dark place. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Neoprene rubber is a chloroprene rubber, which has excellent mechanical property & good abrasion resistance. It gives good resistance to oil & heat, ozone, sunlight & weather and also gives good adhesion to metal surface. Neoprene rubber sheets / rolls are available for a range of applications in the industries. Many grades of neoprene are available depending on the application. These rolls will handle most tough industrial environments and moderate to heavy alkaline and chemical resistive situations. It is manufactured in pure neoprene rolls, commercial, medium strength, High Strength, Cloth Inserted, Antistatic, Fire Retardant, and Textured & in Strips. The temperature ranges from (-30°C to +100°C) in operation condition. APPLICATIONS: Neoprene rubber sheets / rolls are mainly used in sealing applications in construction sites & sound studios, general & industrial applications like sealing, gasket & packing to avoid leakages of oil, heat, steam, water, air, acid & alkali. It is also used in marine applications. It has flame retardant properties & good resistance to inorganic chemical products. 100% NEOPRENE RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNP-1445 1.4 45 60 350 2 BNP-1555 1.5 55 70 300 3 BNP-1665 1.6 65 70 250
DESCRIPTION: Nitrile Rubber is a copolymer of butadiene and acrylonitrile. Nitrile rubber sheets are mainly used as oil & solvent resistance as it has good tensile strength, low compression set, flexibility & impermeability to gases. These sheets are very good resistance to petroleum based products having recommended for operating temperature from (-20°C to +110°C). APPLICATIONS: These sheets / rolls are mainly used for sealing, gasket & packing to avoid leakages from oil, solvent, petroleum based fluids, lubricating oil, transformer fluid & sealing against gases. PROPERTY: Very good resistance to petroleum based fluid goods & high temperature resistance up to 110°C. Very low-level permeability to gases. Poor ozone resistance. 100% NITRILE RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNT-1240 1.2 40 60 500 2 BNT-1350 1.3 50 70 450 3 BNT-1460 1.4 60 80 400 4 BNT-1570 1.5 70 80 300 COMMERCIAL GRADE NITRILE RUBBER SHEET NO GRADES NEOPRENE (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BNTNR-50 50 1.6 65 20 250 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 Store according to DIN 7716 standards. Products must be stored in cool, dry places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: EPDM rubber sheet / roll is very good weather-proof quality that makes highly recommended for the outdoor use, These sheets resist to oxidation, UV rays, Ozone, weathering & low temperature flexibility. The operating temperature range is from (-40°C to +130°C). EPDM rubber sheets / rolls are stable for long time due to its inert structure APPLICATIONS: EPDM rubber sheets are highly used for industrial & outdoor application like weather strips, drinking water applications, rain water sealing, protection against sunlight & heat gaining as a roofing membrane & acid resistance applications. Also useful as a liner in pulverizing system. PROPERTY: Very good resistance to water & water-based chemicals withstand temperature up to 130°C. Very good weathering resistance. Good resistance to mild acids, liquid fertilizer & break fluids. No resistance to oil & oil based products. 100% EPDM RUBBER SHEET: BLACK NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BEP-1155 1.1 55 70 500 2 BEP-1260 1.2 60 80 400 3 BEP-1365 1.3 65 100 300 4 BEP-1470 1.4 70 70 250 COMMERCIAL GRADE EPDM RUBBER SHEET NO GRADES EPDM (%) DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BEPNR-50 50 1.5 65 50 250 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places Avoid contact with hydrocarbons, solvents, acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Butyl Rubber sheet / roll are a very low permeability to air & other gases. These sheets have excellent resistance to sunlight, ozone & oxidation. The operating temperature resistivity ranges from (-30°C to +110°C). It is resistant to most inorganic products and best resistance to mineral acids & alkaline. APPLICATIONS: These sheets / rolls are used for Chemical tank lining, Pharmaceutical stoppers, Acid protective clothing & many more applications. PROPERTY: Very good resistance to acids & alkalis. Very good for low resilience applications like shock absorber & vibration dampers. Not recommended its use in applications where resistance to oils & hydrocarbons is required. NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BIIR-12560 1.2 55 80 350 2 BIIR-13065 1.3 60 60 300 3 BINR-60 (IIR: NR = 60:40) 1.3 65 70 350 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with hydrocarbons, solvents. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
DESCRIPTION: Diaphragm Rubber sheets are manufactured by inserting 1 ply & 2 ply Nylon Fabric used as Diaphragms for wide variety of applications specifically for Oil, LPG & solvent resistant applications. Recommended use for control valves, regulators, pumps etc. Diaphragm sheet is manufactured with high quality Nitrile rubber compound designed for long service. This rubber sheet is reinforced with multi-ply fabric to provide desired strength. The purpose of providing insertion is to provide additional strength to material in order to make it more pressure proof. Selection of fabric is available on request. NO GRADES DENSITY (g/cc) HARDNESS (SH–A) TENSILE (Kg/cm2) Eb (%) 1 BDR-1370 1.3 70 80 300 PRODUCT DIMENSIONS Rotocure Finish Plate Finish SIZE (Mtrs) THICKNESS (MM) 1.2 x 10, 20, 30 3 to 12 Finish Smooth / Texture Impression SIZE (Mtrs) THICKNESS (MM) 1.2 x 2.4 3 to 25 1.0 x 2.0 3 to 25 MANUFACTURING TOLERANCES THICKNESS WIDTH LENGTH HARDNESS DENSITY + / - 0.3mm or 10% whichever is higher + / - 2% + / - 5% + / - 5 + / - 0.05 RECOMMENDATIONS REGARDING STORAGE AFTER RECEIPT Store according to DIN 7716 standards. Products must be stored in cool, dry & dark places with temperature ranging between 10°C to 30°C, sheltered from the sun & free from ozone for better shelf life. Avoid contact with acids & alkalies. If there is any doubt about the condition of sheet/roll, they should be retested before putting into service. Products should be issued in the order of their date of manufacture.
Rubber Stocks
Since 2018 year, we are completely carried out the whole production line from mold, Refining ,trimming, Assembly with the most professional rubber vulcanizing equipment, the innovative R&D sprite, strong production capacity, strict quality control that make us well to produce the material of NR,NBR, EPDM,SIR,LSR,CR,,SBR,FKM,PU,PP,PVC,PE,PC,ABS etc, Now the capacity more than 20000000pcs/day to ensure the lead time on time! We are cooperate well with domestic and abroad, such as USA Germany, France, UK, Italy, with famous brand, such as Kohler, Dollar General, B&Q and so on. We are ISO9001,IATF16949, Reach and ROHS ,FDA approvals. All kinds of business cooperation are welcomed,
Floating Fender Floating Fender has been used for almost 50 years, it's also called marine rubber fender or YOKOHAMA fenders. It is the leading anticollision device for marine application in the world. Floating Fender is used as a protective medium for ship to ship contact, ship to quay,and ship-to-berthing. Floating fenders are a type of marine equipments that are used to prevent boats, ships and other naval vessels from colliding against each other or against docks, wharves and piers. In other words ship fenders can be simply termed as a marine bumper. LCT use shipside marine balloon fender for STS Why Choose Florescence Florescence is a trusted supplier for shipyard, quay, harbors in the global market. Our factory in Shandong Province has been established for over 20 years. FLORESCENCE Floating Rubber Fenders are sent to lots of countries, including Indonesia, Singapore, America, Russia, etc. Products are certificated by CCS, ISO, ABS, BV, etc. It can be manufactured in different kinds of sizes and types according to the customers' requirements. Our floating fender business has recently opened the door to the Floating LNG market, one of the most challenging applications in the offshore industry. Several 3.3*6.5m size fenders will be used in between the largest floating production facility in the world and LNG carrier during the side-by-side operation. Florescence is currently in the process of developing larger size fender and advanced monitoring system to better serve our customer needs.
Foam Filled fenders are manufactured from high quality foam covered by a tough Polyurethane skin. Florescence manufactures Foam Filled Fender as an alternative to the standard Pneumatic Fender. The performance of foam filled fenders can be modified by changing the grades of foam. This also gives more flexibility to foam filled fenders in meeting different requirements of berthing energy and reaction force as compared to same size of fenders. Foam filled fenders can also be equipped with a chain and tire net for rough applications. Since there is no air pressure inside the fender, there is no risk of deflating, bursting or sinking. As there are no end fittings like safety valves, ball valves etc., there is less maintenance required for Foam filled fenders compared to Pneumatic fenders. However, foam filled fender of higher size above 2.2 Meter diameter are generally more expensive when compared to Pneumatic fenders due to the high freight cost.
Floating Fender Floating Fender has been used for almost 50 years, it's also called marine rubber fender or YOKOHAMA fenders. It is the leading anticollision device for marine application in the world. Floating Fender is used as a protective medium for ship to ship contact, ship to quay,and ship-to-berthing. Floating fenders are a type of marine equipments that are used to prevent boats, ships and other naval vessels from colliding against each other or against docks, wharves and piers. In other words ship fenders can be simply termed as a marine bumper. LCT use shipside marine balloon fender for STS Why Choose Florescence Florescence is a trusted supplier for shipyard, quay, harbors in the global market. Our factory in Shandong Province has been established for over 20 years. FLORESCENCE Floating Rubber Fenders are sent to lots of countries, including Indonesia, Singapore, America, Russia, etc. Products are certificated by CCS, ISO, ABS, BV, etc. It can be manufactured in different kinds of sizes and types according to the customers' requirements. Our floating fender business has recently opened the door to the Floating LNG market, one of the most challenging applications in the offshore industry. Several 3.3*6.5m size fenders will be used in between the largest floating production facility in the world and LNG carrier during the side-by-side operation. Florescence is currently in the process of developing larger size fender and advanced monitoring system to better serve our customer needs.
Material: EPDM or according to your requirement. Hardness: 705 ShA Size: Customized according to your drawing or sample Do you have inquiry of it or similar rubber product? Please contact me directly. We still have many other models, I can send you our more information if it's ok for you. I'm waiting here for your reply.
Material: EPDM, NBR, CR, NR, Silicone Hardness: 30shA 90shA Size: Customized according to your drawing or sample Packing: Plastic bags in carton or according to your requirements Welcome your any inquiry, most professional suggestions help you get more profits. Hope to hear your early reply soonest.
Material: EPDM+PVC, or according to your requirement. Hardness: 70±5 ShA Tooling cost: most of sizes are without tooling cost. Service: usually 50m/roll or as per customers' package.
- RSS3 rubber sheets are used in the production of Tyres (tires) & Tubes, Tread Carcass, Off road tyres & ADV tyres, Extruded hoses, Footwear etc. Tyre industry is the biggest consumer of RSS3 rubber sheets. - Dry mould no more than 10%, clean , dry, strong, small-scattered bubbles, specks of bark, free from blemishes, sand, foreign matter, under-cured. Dirt (Max % Wt) 0.008 Ash (Max % Wt) 0.304 Volatile matter (Max % Wt) 0.34 Nitrogen content (Max % Wt) 0.43 PRI (Min) 83.1 Innitial Wallace plasticity 41
Material: EPDM, NBR, CR, NR, Silicone Size: Customized according to your drawing or sample Quality: RoSH verified compound; Packing: Plastic bags in carton or according to your requirements
Ship rubber airbag Ship rubber airbag is also known as rubber airbag, ship launching airbag, ship salvage airbag, boat salvage airbags, inflatable airbag, ship lifting bag, air balloon, made by rubber & multi layer of rubber-dipped tire fabric. Airbags are widely used in launching and landing ship/ boat/vessel, lifting and moving heavy objects, caisson floating, marine engineering. Rubber airbags are very popular among shipyard, ship owner, and marine supplies company now. Florescence ship rubber airbag. Florescence has our own factory which manufacture rubber products for almost 20 years, so we are the factory direct seller, we are more professional than other companies. Florescence ship rubber airbags are expoted to many countries, including indonesia, singapore, america, russia, etc. Florescence ship rubber airbags can be manufatured in various sizes and types according to the customers' need. 1. Structure of the florescence marine launching airbag 1. Airbag body The airbagbody is composed by natural rubber and strength fiber material through vulcanization progressing 2. Terminal iron part The terminal iron part is made of cast iron, it is combined closely with the airbag body, one end is for pulling when you move it, and the other end if for charging and discharging the air. 2. Advantages of marine launching airbag 1. Different size airbag stock available, quick delivery 2. Provide repair kit and on site instruction 3. Long time service life can be used many times 4. Wear resistance and anti aging 5. Good raw material and cord fabric 6. Harmless to the enviroment, time&money saving 7. Need no more than air compressors, winches and ropes 8. Using marine airbags are much cheaper and portable than other methods
Pneumatic rubber fender Pneumatic rubber fender has been used for almost 50 years, it's also called marine rubber fender or yokohama fenders. It is the mian anticollision device for marine application among the world. Pneumatic rubber fender is used as a protective medium for ship to ship contact, ship to quay, and ship-to-berthing. Pneumatic rubber fenders are a type of marine equipments that are used to prevent boats, ships and other naval vessels from colliding against each other or against docks, wharves and piers. In other words ship fenders can be simply termed as a marine bumper. Why choose florescence. Florescence is a trusted supplier for shipyard, quay, harbors in the global market. Our factory in shandong province has been established for over 20 years. Florescence pneumatiuc rubber fenders are exported to many countries, such as indonesia, singapore, france, india, etc. Products are certificated by ccs, iso, abs, bv, etc. It can be manufactured in different kinds of sizes and types according to the customers' requirements.
