APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Tiles Adhesive (CT-01),(02),(03), Tiles Epoxy Grout, Tiles Grout (Light Color), Tile Grout (Dark Color), Tiles Epoxy Grout Sparkle, Block Jointing Mortar, Wall Putty, Floor Hardener Non-Metallic, Tile Spacer (2mm, 3mm, 4mm,5mm), SBR. Etc. Products are available in stock.
Construction Chemicals
In co-operation with major manufacturers in Turkey, FALMER is able to supply a wide range of products, including construction chemicals. Our aim is to supply the most excellent thermal insulation materials and construction chemicals and to bring them together with the end consumer. To contribute to the national economy by minimising the increasing energy demand of our world with our insulation materials. WHITE SEALANT 450 GR COLORED SEALANT 450 GR SILICONE CLEAR 280 GR POLYURETHANE LIQUID NAIL 450 GR SILICONE-BASED JOINT FILLER 380 GR CORNICE ADHESIVE 450 GR STYROFOAM CORNICE ADHESIVE 450 GR WOOD GLUE 100 GR WOOD GLUE 350 GR WOOD GLUE 700 GR SPRAY PAINT INTERMEDIATE COLORS 200 ML (160 GR) SPRAY PAINT INTERMEDIATE COLORS 400 ML (300 GR) SPRAY PAINT METALLIC â?? GOLD 200 ML (160 GR) SPRAY PAINT METALLIC â?? GOLD 400 ML (300 GR) CLEAR VARNISH 200 ML (160 GR) CLEAR VARNISH 400 ML (300 GR) PAINT REMOVER 200 ML (160 GR) PAINT REMOVER 400 ML (300 GR) POLYURETHANE FOAM 600ML SILICONE SPRAY 500 ML (380 GR) BRAKE PAD AND CLUTCH CLEANER 500 ML (390 GR) LABEL AND STICKER REMOVER 200 ML (160 GR) LIQUID GREASE 200 ML (160 GR) LIQUID GREASE 400 ML (350 GR) RUST REMOVER 200 ML (170 GR) RUST REMOVER 400 ML (320 GR) G-60 LUBRICANT 200 ML (170 GR) G-60 LUBRICANT 400 ML (320 GR) FAST ADHESIVE 200 ML (35 GR JAPON) FAST ADHESIVE 400 ML (75 GR JAPON) MOLD RELEASE 400 ML (350 GR) CHAIN LUBRICANT400 ML (350 GR) WATERPROOFING SPRAY 400 ML (350 GR) CHEMICAL ANCHOR LIGHTER GAS 270 ML CAMPING GAS 227GR ZINC SPRAY 400ML (350GR) GAS DUSTER SPRAY 400ML DRAIN CLEANER (500 GR) DRAIN CLEANER (1000 GR) DRAIN CLEANER (2000 GR)
Its used in construction industry. For price, specifications and more details please contact us
Polycarboxylate superplasticizer products have been extensively used in cement or gypsum-based mortars with high fluidity and high strength requirements. It is widely used in fluid mortars, such as fluid mortar for pouring, paving, and painting. For price, specifications and more details please contact us
Naphthalene Sulfonate Formaldehyde Condensate (SNF), also known as Poly Naphthalene Sulfonate (PNS) and Formaldehyde Sulfonate Condensate (FDN), is a highly effective water reducer and superplasticizer commonly used in the construction industry to improve the workability and strength of concrete.
It is a high range water reducer, high concentration naphthalene-based superplasticizer, also named Naphthalene Sulfonate Formaldehyde Condensate SNF, PNS and FDN etc. Na2SO4 has 3 grades:5% 10% 18% for exporting markets,in domestic we also have 3% 23% Na2SO4 content FDN.It contains no chloride, non-corrosive to steel bars, non-poisonous, odorless, and non-flammable.
PCE superplasticizer is the newest generation superplasticizer used for concrete in domestic and abroad.It is based on molecular designs and adsorption capacity of polycarboxylate,we do R&D and successfully produce water reducing and retention type polycarboxylate superplasticizer for concrete.With initiating systerm and reaction conditions,we achieve high adaptability.Comparing with PNS and other superplasticizer, PCE superplasticizer has many characteristic advantages in technology and performance as following: (1) low dosage, high rate of water reducing; (2) keep concrete good slumption retention; (3) good compatibility with cement; (4) small shrinkage of concrete to keep the stability of volume and durability; (5) environmental in production and usage. Base on above advantages.
Resin finishing of woven and knitted fabrics composed of cellulosic fibres and their blends with synthetic fibres. For embossed, schreiner and chintz finishes. The finished textile materials have a very low formaldehyde content particularly in the LAW 112 and AATCC 112 test methods meeting the Oeko-Tex standard 100 of 75 ppm free formaldehyde. CD-281 shows good finish effects that have a high stability to hydrolysis, and are also fast to washing at the boil and to dry cleaning.
Bondacoat Ar Bondacoat Ep Bondacoat Pva Bondacoat Sbr Epogrout Hs Rendragrout Hf (Adhesive & Grouts) Tile Adhesive Ep Tile Grout Ep Epomortar Fc Eposcreed 10 Fillgrout Ep10 Fillgrout Pu40 Rendacoat Fc Rendagrout Hf (Concrete Repairs) Concoat Ep100 Concoat Ep150 Concoat Ep250 Concoat Resin Concoat Sl Elastoguard Pu Prime Ep100 Tg Prime Ep100 Prime Eps Prime Eps40 Proofseal Pu Concoat Eps Concoat Ept500 Deguard Sheild Sn- Wr636 Deguard Sheild Sn Waterbased- Wr637 Concoat Slc90 Elastocryl 700 Elastocryl 800 Elastocryl 900 Epocoat Epwp Epoflex 500 Proofseal Pt Epocoat Epwp Epoflex 500 Proofseal Pt Proofseal Pu Epogrout Hs
Superplasticizer based on melamine and Polycarboxylate, of very good quality. Used on mortars and concrete, etc.
YL-SNF-C(Na2SO4 less than 18%) Sodium Naphthalene Sulfonate Formaldehyde This product, named -naphthalene sulfonate formaldehyde condensate, is non-air entraining superplasticizer. It has good dispersing performance to the cement particles. Compared with traditional plasticizer, it has higher water reducing rate, and good for preparing mass concrete, fresh concrete required for early strength and high strength, and precast concrete and parts. It also has good adaptability to commonly used cement, and widely used in roads, bridges, dams, power engineering, civil construction, steam and natural curing precast parts and other projects. Advantage: * Higher water reducing rate. By the recommended dosage, the water reducingrate can reach 15% -20%. * Improve the workability of concrete, such as compression, long-term strength, flowability, etc., and enhance the reinforcement of steel and concrete. * Reduce costs. In the case of maintaining the same workability and strength, cement amountcan be reduced. * Wide adaptability, cost-effective. Good adaptability to all kinds of cement, such as Portland cement, slag cement, volcanic ash cement, etc. * Be mother material to formulate other admixtures.(like early strength, set retarder, pumping agent, antifreezing agent).
Supplying business of construction chemicals like Water proofing coating material for plaster and concrete
YL-PL-WR Polycarboxylate Superplasticizer (Water reducing type, 40-50% solid content) * High water reduction, low dosage. The water reducing rate can reach 20%-40% with recommended dosage. * Early and high strength. The early strengthand 28 day strength have been obviously improved. * Low slump loss: complywith the pumping agent standard, slump loss would besignificantly reduced. * High durability: This product can effectively reduce the W/C ratio, improve durability. * It can be used as a mother liquor to produce other functional admixture, such as early strengthtype, retarder, pumpingconcrete admixture, antifreezer, etc.; * Environmentalfriendly products: the production does not pollute the environment; * Non-corrosionon steelbar.
1. Increasing productivity and improving quality in cement grinding process 2. Saving the production cost and time 3. Anti-coagulation and stable grinding ability 4. Increasing early and long term strength 5. Reduction of CO2 emission and energy cost.
1. Increasing productivity and improving quality in cement grinding process 2. Saving the production cost and time 3. Anti-coagulation and stable grinding ability 4. Increasing early and long term strength 5. Reduction of CO2 emission and energy cost.
Sodium naphthalene sulphonate fdn- 1 used for and widely for self-cured, vaporcured concrete and its formulations. At the early stage of Application, extremely prominent effects are shown. As the result, the modulus and siteutilization Can be drastically, the procedure of vapor cureis omitted in peak-heat summer days. Statistically 40-60 metric tons of coal willbe preserved when a metric ton of the material is consumed. 2 suitable for preparation of early-strength, high-strength, high-anti-filtration and selfsealing& pumpable concrete.
Main performance 1. Can be applied as common water reducing admixture and built material of series multifunction high-performance water reducing admixtures. 2. Can be adopted as the adhesives in the briquetting procedure in the vertical retort zinc smelters. 3. Can be used as embryo reinforcing agents in the fields of pottery and porcelain and refractory materials. They can increase the fluidity of the slurry and thus to improve the strength of the embryo. 4.In the field of water-coal paste, the sodium lignosulphonate series products can be adopted as the main compound materials. 5.In agriculture, the sodium lignosulphonate series products can be applied as the dispersant agents of pesticides and pelleting adhesives of fertilizers and feedstuffs.
