Our capabilities: Peroxide and platinum cured polymers, both of which can meet food quality requirements. Hardness range: 35-85 Shore A Colours available: Translucent White Black Grey Red oxide Bright red Green Yellow Blue Colour matching available on request. Drawings: Please click following links for the drawings of our stocked silicone extrusion profiles. drawing 1 to 4. drawing 5 to 8. drawing 9 to 12. drawing 13 to 15 Temperature resistance: -50 to +260 Degrees Centigrade (up to 300C for short periods) Sizes available: Flat strips are available in continuous lengths up to 80mm wide. Minimum thickness 0.5mm. Cords and tubes are available up to 60mm Diameter. Minimum tube ID is 1mm Joining: Most profiles can be joined to form endless seals. Hollow and solid O rings are available in a wide range of sizes. Most profiles can be joined to any required angle to form (for example) rectangular gaskets.
Solid Silicone Sheet/ Silicone Rubber Sheet materials are inventoried by Seashore Manufacturing Limited from 0.5mm to 20mm thick and 30 to 70 durometer(hardness) Shore A. Our Solid silicone sheeting continues to grow and is available in four standard colours white, translucent, red oxide and black. The dimensions for silicon rubber sheet of our stock stardard is in the following: 500mmx500mmx0.5mm 800mmx800mmx1.0mm 1000mmx1000mmx1.5mm 1000mmx10mx from 1mm to 20mm 1200mmx10mx from 1mm to 20mm 1500mmx10mx from 1mm to 5mm 1800mmx10mx from 1mm to 5mm 2000mmx10mx from 1mm to 5mm The specification of most standard silicone sheet we produce are as below: Density:1.25 g/cm3 Handness:55 Shore A Tensile strength:7.0 mpa Elongation at Breakage:320% Tension Set:8% Tear Strength:20 KN/M Heat Resistant: 200 C Sizes Thinkness tolerance(+/-mm) 10mx1m or 1.2mx1mm 0.1 10mx1m or 1.2mx2 to 6mm 0.2 10mx1m or 1.2mx7 to 10mm 0.3 The above is silicone rubber sheet standard at Shore A Hardness 40,50,60. Other sizes, colours and hardnesses are available on request. Beside standard ones,we supply FDA food grade silicone sheet,anti-static silicone sheet,anti-acid silicone sheet. Special silicone sheet is use of wood/chipboard laminating,glass industrial,solar industrial. Our Solid silicone rubber sheet is 200 degree centigrade temperature resistant as standard,but we also can do high temperature resistant up to 270 degree centigrade. Sponge Silicone Rubber Sheet 100% closed cell Silicone Rubber material,double sides fabric impression or smooth finished. Our sponge silicone sheeting is available in four standard colours white, red oxide,black. The dimensions for sponge silicon rubber sheet of our stock stardard is in the following: 1000mmx1000mx from 3mm to 20mm 2000mmx1000mx from 3mm to 20mm 5000mmx1000mx from 3mm to 20mm The above is sponge silicone sheet standard at Shore A Hardness 10,20,30. Other sizes, colours and hardnesses are available on request. Our sponge silicone rubber sheet is 200 degree centigrade temperature resistant as standard. Sponge silicon rubber sheet material is readily fabricated into gaskets and cushioning pads.
SBR Rubber sheet SBR Rubber has properties similar to Natural Rubber. It has good abrasion resistance, excellent impact strength, very good resilience and a high tensile strength. Applications: SBR can be compounded for use as lining rubber, conveyor belt covers and other extremely demanding applications. Size: 1000mmx1000mmx1mm to 50mm 1200mmx1200mmx1mm to 50mm 1000mmx10mx from 1mm to 25mm 1200mmx10mx from 1mm to 25mm 1500mmx10mx from 1mm to 20mm 1800mmx10mx from 2mm to 20mm 2000mmx10mx from 2mm to 20mm Finish:Smoothly finished or both side fabrics impress on finished. Insertion:common cloth insertion or nylon fabric insertion Color available is black,red,white,blue,green etc. TYPICAL PHYSICAL PROPERTIES AND VALUES: Hardness, Shore A +/-5 60 Specific Gravity (DENSITY) 1.6g/cm3 Tensile Strength 3mpa Enlongation Break 250% Heat Aging(70 Cx72hours) Tensile Strength Change 20% Elongation Break 25%. Other specifications we can produce per your request.
Silicon metal (si 99.28%) Silicon metal-553 Silicon metal-3303
1.Application of brushing rtv-2 molding silicone rubber : Brushing rtv-2 molding silicone rubber mainly used for shoe molds, sand casting, sole sampling, plaster models, simple products, products with non-complex patterns, as well as product models with stable size and non-deformation. 2.Operation instruction of brushinng silicone rubber : Brushing rtv-2 molding silicone rubber is composed of two components.Component a is white flowing liquid while component b is the curing agent. Steps: A. Take silicone rubber of 100g and add 2% curing agent for mixing evenly. B. After the silicone rubber and the curing agent are completely mixed, put the silicon into a vacuum machine for deairing to remove the bubbles. C. After deaired, pouring the liquid silicone rubber into the product to be duplicated or into the mold frame. Note: brushing rtv-2 molding silicone rubber is used for pouring or brushing technique. That is to say, Firstly fix the product or sole model to be duplicated onto a plane plate, Then enclose the plane frame with wooden plates to prevent the leakage of the silicon , Thirdly mix the silicone rubber and the curing agent evenly according to the mixing ratio of 100: 2 and pour them onto the sole model, At last brush evenly with a wooden plate or a brush, and fill up the mold frame with gypsum after the silicone rubber is dried. 3. Storage and precautions of brushing molding silicone rubber : 25kg/drum, 200kg/drum
Usage of liquid rtv silicone rubber for sculpture molding Liquid rtv silicone rubber for sculpture molding is intended for making silicone rubber mold for resin crafts, candles, plastic toys, relieve furniture, architectural decoration, furniture decoration, sculpture and so on. Feature of liquid rtv silicone rubber for sculpture molding Liquid rtv silicone rubber for sculpture molding is flowing liquid with general hardness of 22-50 a ++p after curing with features: 1) low shrinkage 2) good operation 3) high tear and tensile strength 4) curing agent free 5) easy de-mold 6) high reproduction times 7) resistance to deformation and high-temperature, acid-alkali Operations of liquid rtv silicone rubber for sculpture molding If customers want to make large products and large size moulds, the mould should be made of silicone rubber with high hardness. On the contrary, if the mould with fine and precision patterns, it should be made of silicone with low hardness. The amount of the curing agent depends on the actual requirements of the customer. If mould requiring fast drying and demould, more curing is needed. 25kg/drum, 200kg/drum
Applications of rtv 2 molding silicon rubber: Silicone rubber is mainly applicable to manual mold design, pvc plastic molds, cement product molds, melting point alloy molds, alloy toy craftworks, plastic toy craftworks, gifts and stationery, large statues, duplication of cultural relics, shoe sole mold fabrication, pad printing positioning, shock resistance for electronic equipments, etc. Description of rtv molding silicon rubber: Silicine rubber for manual moid is flowing liquid with consistant quality in whatever color. It consists of two components, wherein component a is silicone rubber, and component b is curing agent or vulcanizing agent. Firstly process and prepare the model mold or the product to be duplicated, take certain amount of the silicone rubber, add 2-3% solidifying agent, and mix evenly for use. One mold pair can be solidified and formed in 2-3 hours. The formed mold can be used repeatedly without deformation and water shrinkage and with high temperature resistance, thereby providing fast duplication of the product with a product shrinkage 2. The 418 manual mold silicon is mainly applicable to manual molds and small number of product duplication. Operation instruction of rtv molding silicon rubber:: 1. The manual mold silicon is applied to small products or products with fine patterns. The mold for the fine detailed and small products should be made of soft silicon to protect the products from easy breaking when demoulding. 2. If large product duplication or fabrication, the mold should be made of higher hardness silicone rubber so that the products made will not deform. 25kg/drum, 200kg/drum
Our rubber extrusions can be in almost all shapes:extruded rubber tubings, O-ring cord,squares and rectangles,strip, edge trims,fenders,"U" channel ,"D","P","L","E" shapes,etc,in any sizes you need. Rolls in cartons.
All the shapes of rubber seals can be able to be extruded,including D section,P sections,E section, L section,U- channel,bubble section,key-hole section,triangle sections,etc ,or custom rubber seal. Material could be in EPDM Rubber,Silicone rubber,Viton Rubber,Foam rubber,PVC,TPE,etc.Co-extruded rubber seals can be available. Rolls in cartons
Silicone Sheet Durable seaworthy packing
As your requirement As your requirements
Silicon rubber heaters have wire-wound or etched foil heating elements protected by Fiberglass-reinforced silicon rubber vulcanized and compressed at high temperature and press. They are thin, bendable and shaped to fit almost any equipment. Heat can be applied to the Most complex shapes, geometries, curves and pipes conceivable without sacrificing efficiency or Dependability. Techical parameters: 1 maximum temperature resistance of insulatorú¦300íµ 2 maximum operation temperatureú¦ 250íµ 3 insulation resistanceú¦í²500 mª+/dc 1000v 4 breakdown voltageú¦í² ac1500v/5s 5 capacity toleranceú¦ía5% 6 temperature range: -60íµí¬250íµ continuous heating; heating element: available with either Etched foil or wire-wound elements: 7 dimension:maximum 1.2míßxm minimun 15mmíß15mm; thickness 1.5mmú¿thinnest 0.8mmú¼ Thickest 4.5mmlead wire length:standard 130mm. Installation: 1 with backing psa (pressure sensitive adhesive or called self adhesive, self stick adhesive) As 3m psa 2 with vulcanization or curing and compression at high temperature and press 3 with spring and hole or eyelet 4 with clamps Benefits: 1 heating evenly, accurate and adjustable 2 various shapes, holes, cutouts, profiled watt densities and multiple voltages 3 put heat exactly where it is required 4 high dielectric strength, flexibility, bendable and cost effectiveness. 5 resistance to temperature extremes, moisture, weathering, radiation, fungus and chemical Attack 6 heat can be applied to the most complex shapes, geometries, curves and pipes conceivable Without sacrificing efficiency or dependability. 7 easily bonded and/or mechanically mounted, even onto the curving surface.
Honeywon»s silicone sponge is with high grade silicone rubber material and inimitable technique, with Good character of high temperature resistant, aging resistant, ozone resistant, insulation property, fuel Oil resistance, lubes resistance, no smell and wear well. High compressibility and low compression set Over a wide temperature range, and good acoustic and thermal insulation properties. Apply to -50µ ~+200µ protect and heat insulation for long term continuous use and -70µ ~ +260µ for intermittent Use on all kinds of machine. Feature: Standard size(mm)+ 290*380*¿5-15) 380*380*(5-15) 400*600*(5- 15) 500*500*(2-30) 500*600*(5-15) 600*800*(5-15) 1000*1000*(5-12) 1000*1200*(5-12) Special size(mm)+minimum length:no limitation maximum length:no limitation, or in roll Minimum width:no limitation maximum width:1200 minimum thickness:3.0 maximum Thickness:30.0 Product color+ red¼grey¼natural, white¼black or any other required color Application+ heat transfer print equipment, electronics and electrics, machine and sealcharacter+high temperature resistant, aging resistant, ozone resistant, insulation property, fuel oil Resistance, lubes resistance, no smell and wear well, good acoustic and thermal insulation properties. + technical index¦ Style¦ open cell Surface¦double fabric impression Tear strength¦55kn/m Press strength+30mpa Elongation¦100% Hardness¦8-50 shore a Temperature range¦-50-220c continuously; -70µ ~ +260µ for intermittent use Density¦0.55-0.9g/cm3 Flame resistance¦94v-0 Dielectric breakdown voltage¦>3kv Dielectric constant¦5.5 khz Tensile strength: 10-30psi Volume resistance¦1.*1011 ohm-m Thermal conductivity¦0.1 w/m-k Thick tolerance: a0.05mm~0.1mm
Silicon rubber heaters have wire-wound or etched foil heating elements protected by Fiberglass-reinforced silicon rubber vulcanized and compressed at high temperature and press. They are thin, bendable and shaped to fit almost any equipment. Heat can be applied to the Most complex shapes, geometries, curves and pipes conceivable without sacrificing efficiency or Dependability. Techical parameters: 1 maximum temperature resistance of insulator¦300íµ 2 maximum operation temperature¦ 250íµ 3 insulation resistance¦í²500 mª+/dc 1000v 4 breakdown voltage¦í² ac1500v/5s 5 capacity tolerance¦ía5% 6 temperature range: -60íµí¬250íµ continuous heating; heating element: available with either Etched foil or wire-wound elements: 7 dimension:maximum 1.2míßxm minimun 15mmíß15mm; thickness 1.5mm¿thinnest 0.8mm¼ Thickest 4.5mmlead wire length:standard 130mm. Installation: 1 with backing psa (pressure sensitive adhesive or called self adhesive, self stick adhesive) As 3m psa 2 with vulcanization or curing and compression at high temperature and press 3 with spring and hole or eyelet 4 with clamps Benefits: 1 heating evenly, accurate and adjustable 2 various shapes, holes, cutouts, profiled watt densities and multiple voltages 3 put heat exactly where it is required 4 high dielectric strength, flexibility, bendable and cost effectiveness. 5 resistance to temperature extremes, moisture, weathering, radiation, fungus and chemical Attack
Honeywoní»s silicone sponge is with high grade silicone rubber material and inimitable technique, with Good character of high temperature resistant, aging resistant, ozone resistant, insulation property, fuel Oil resistance, lubes resistance, no smell and wear well. High compressibility and low compression set Over a wide temperature range, and good acoustic and thermal insulation properties. Apply to -50í ~+200í protect and heat insulation for long term continuous use and -70í ~ +260í for intermittent Use on all kinds of machine. Feature: Standard size(mm)í+ 290*380*ú¿5-15) 380*380*(5-15) 400*600*(5- 15) 500*500*(2-30) 500*600*(5-15) 600*800*(5-15) 1000*1000*(5-12) 1000*1200*(5-12) Special size(mm)í+minimum length:no limitation maximum length:no limitation, or in roll Minimum width:no limitation maximum width:1200 minimum thickness:3.0 maximum Thickness:30.0 Product colorí+ redú¼greyú¼natural, whiteú¼black or any other required color Applicationí+ heat transfer print equipment, electronics and electrics, machine and sealcharacterí+high temperature resistant, aging resistant, ozone resistant, insulation property, fuel oil Resistance, lubes resistance, no smell and wear well, good acoustic and thermal insulation properties. í÷ technical indexú¦ Styleú¦ open cell Surfaceú¦double fabric impression Tear strengthú¦55kn/m Press strengthú+30mpa Elongationú¦100% Hardnessú¦8-50 shore a Temperature rangeú¦-50-220c continuously; -70í ~ +260í for intermittent use Densityú¦0.55-0.9g/cm3 Flame resistanceú¦94v-0 Dielectric breakdown voltageú¦>3kv Dielectric constantú¦5.5 khz Tensile strength: 10-30psi Volume resistanceú¦1.*1011 ohm-m Thermal conductivityú¦0.1 w/m-k Thick tolerance: ía0.05mm~0.1mm
We are the manufacturer & exporter of all kinds of rubber sheets, rubber compounds, reclaimed rubber, crumb rubber, rubber chemicals & all other related products like precured tread rubber 50 kg
Rubber Sheet: Nature Rubber, Viton Rubber, EPDM Use of Sheets: Automobile Industry, Construction industry, Space industry etc. Sample Service: Free Samples Good quality and sell well We provide raw materials for some large-scale factories in Europe.
Spec. Si%min Fe%max Almax Ca%max Size 553 98.7 0.5 0.5 0.3 10-100mm 441 99.1 0.4 0.4 0.1 10-100mm 331 99.35 0.3 0.3 0.05 10-100mm 2202 99.58 0.2 0. 2 0.02 10-100mm 2502 99.48 0.25 0.25 0.02 10-100mm 3303 99.37 0.3 0.3 0.03 10-100mm 10~100mm 1mt 1 plastic woven bag
Mold making silicone rubber is primarily intended for poly resin crafts, pu crafts, pu resin crafts , gypsum crafts , unsaturated resin crafts, lighting and candles crafts , plastic toy stationery gifts crafts industry, a large statue buddha, furniture, furniture decorative materials, statues buddha, artifacts copied, building decoration materials, large-scale cement mold, artificial fossils factory, europe component factory, simulation landscapes, animals and plants sculpture, sandstone crafts and so on. any more information, please feel free to contact. 25kg /drum 200kg /drum
Superior adhesion on glass, vitrified surfaces, ceramic tiles, most woods, many plastics, most paints and for Do-It-Yourself applications (car, boat, caravan, house etc.). Ready gunnability at low (+5ªC) and high (+40ªC) temperatures Superior flexibility at low (-50ªC) and high (+100ªC) temperatures Colors Available :Grey, white, black and clear. Product Data (Uncured) Density at 25ªC (Method - ISO 1183-1 A) - 0.98~1.05g/ml Skin forming time at 23ªC/50% r.h. v 25 minutes Consistency (Method - ISO 7390, Profile U 20) v Non-sag Extrusion rate at 23ªC (Method - PV 08127) v 800 ml/min. Product Data (Cured) after 4 weeks¦ storage at 23ªC/50% r.h. Tensile strength (Method - ISO 8339) v 0.6N/mm2 Hardness shore A (Method - ISO 868) v 18 Elongation at break (Method - ISO 8339) v 200% Modulus at 100% elongation (Method - ISO 8339) v 0.36 N/mm2 Tear strength (Method - ISO 34, method C) v 4.0 N/mm. 24 cartridges in one box. 1 x 20' will accommodate 2000 cartons.
