Silicone Rubber Foam Pad

Honeywon»s silicone sponge is with high grade silicone rubber material and inimitable technique, with Good character of high temperature resistant, aging resistant, ozone resistant, insulation property, fuel Oil resistance, lubes resistance, no smell and wear well. High compressibility and low compression set Over a wide temperature range, and good acoustic and thermal insulation properties. Apply to -50µ ~+200µ protect and heat insulation for long term continuous use and -70µ ~ +260µ for intermittent Use on all kinds of machine. Feature: Standard size(mm)+ 290*380*¿5-15) 380*380*(5-15) 400*600*(5- 15) 500*500*(2-30) 500*600*(5-15) 600*800*(5-15) 1000*1000*(5-12) 1000*1200*(5-12) Special size(mm)+minimum length:no limitation maximum length:no limitation, or in roll Minimum width:no limitation maximum width:1200 minimum thickness:3.0 maximum Thickness:30.0 Product color+ red¼grey¼natural, white¼black or any other required color Application+ heat transfer print equipment, electronics and electrics, machine and sealcharacter+high temperature resistant, aging resistant, ozone resistant, insulation property, fuel oil Resistance, lubes resistance, no smell and wear well, good acoustic and thermal insulation properties. + technical index¦ Style¦ open cell Surface¦double fabric impression Tear strength¦55kn/m Press strength+30mpa Elongation¦100% Hardness¦8-50 shore a Temperature range¦-50-220c continuously; -70µ ~ +260µ for intermittent use Density¦0.55-0.9g/cm3 Flame resistance¦94v-0 Dielectric breakdown voltage¦>3kv Dielectric constant¦5.5 khz Tensile strength: 10-30psi Volume resistance¦1.*1011 ohm-m Thermal conductivity¦0.1 w/m-k Thick tolerance: a0.05mm~0.1mm

INTRODUCTION: Silicone Foams is a soft, two-component platinum silicone flexible foam that is versatile and easy to use. Vibrant colors can be achieved by adding color pigments. Cured foam is high heat resistance (will resist up to 350°F/176°C), water resistant, UV resistant and resists oxidation and ozone degradation. FEATURE: 1.Mixed Viscocity 2.Very soft 3.Excellent temperature resistence IMPROVE SURFACE FINISH AND MINIMIZE VOIDS WITH BACK PRESSURE: Use a board that will completely cover the mold opening. Using a drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes. APPLICATION: Silicone Foams can be used for a variety of industrial and special effects applications including making foam filled appliances, padding/seat cushioning, orthotics/orthopedics, potting and encapsulation of electrical circuits and vibration dampening. ABOUT US: We are engaged in silicone rubber's R&D since 1996,there are experienced technicians and workers in our company,as well as advanced equipment.We produce almost all kinds of silicone rubber,which we believe must meet your possible requirements, no matter what you need to produce by silicone rubber. What's more,our silicone rubber are environmental-friendly production,with high safety and no toxic.You can absolutely trust your choice with us. For more information, welcome to contact Lilian: Wechat / Phone: 8613617490457 E-mail: lilian(at)xrsil(dot)com Skype: lilian-xrsilicone Company: Dongguan Xinrun Silicone New Materials Co., Ltd / Xinrun Group Limited Factory address: No.2,Zhouliao Road, Langzhou Industrial Zone,Changping, Dongguan, Guangdong, China

The pad printing silicon rubber is a carrier which transfers the patterns from the steel plate onto the products' surface. The pad printing silicon rubber has the advantages of good printing effects,good quality,good resilience and without any impurity. Pad printing silicon rubber is mainly applicable to the printing of irregular patterns on plastics toys,electronplating products,electronic toys, trademarks,artwork gifts ,stationeries etc. Applications of liquid pad printing silicone rubber Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface. 2. Features of liquid pad printing silicone rubber a. resistance to deformation, high-temperature b. high printing times c. good aging resistance d. exceptional elasticity e. great printing effect 3. Operation Instructions of liquid pad printing silicone rubber Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. The usual mixture of silicone rubber and catalyst is 100: 2 or 100: 3. E.g. we take 100g of liquid silicon rubber and 2g-3g catalyst, mix them and pour it to your mold. A fter 2-4 hours, you will get a Pad printing silicone rubber. HY-918 with the advantages of high temperature resistance, abrasion resistance,  good printing effect, etc. , which made of top-quality raw material due to adding American Dupont Teflon high-temperature resistance new material, is processed through high-temperature machining. The product is mainly applicable to plastics toys, electroplating products, electronic toys, trademarks and irregular pattern printing. The silicon pad is a carrier which transfer printing the patterns on the steel plate onto the toy products' surface. HY-918 is a kind of silicone rubber to make the printing pads for plastic toys, craft works, product printing. Characteristics good printing effects good quality good resilience and without any impurity.

Silicone rubber for pad printing features description Pad printing silicone rubber with highprint times and abrasion resistance, without any impurities, with good printingeffects, permanent and durable, we can provide all kinds of colors and ourcatalyst is free charged. Applications： The pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys, trade makers .Silicone pad printing is a carrier which transfer printing the patterns on the steel plate onto the toys products surface. Silicone rubber for pad printing instructions Pad printing silicone rubber istwo-component silicone, part a is the liquid silicone rubber, part b is thecatalyst. The usual mixing ratio for silicone rubber and catalyst is100 : 2-3, eg. We take 100grams of liquid silicone rubber, then weadd 2-3 grams catalyst, mix then evenly and pour it to your mold.Then after 2-4 hours, you will obtain a printing pad. Features 1.Non-exothermic 2.Mold-releasability 3.Dimensional stability 4.Excellent flowability 5.Heat & chemical resistance 25kgs/drum vacuum package or 200kgs/drum

Pad printing silicone rubber is rtv2 silicone, also called two components silicone or two parts silicone, part A and B will vulcanize in room temperature when A and B mixed. The mix ratio of tin cure silicone is 100:3, the platinum cure silicone is 9:1.

Description of Liquid Silicone Rubber for Pad Printing Liquid Silicone Rubber for Pad Printing Mainly used for making plastic toys, electroplating products, electronic toys, trademarks, communications equipment, gifts, stationery and other irregular pattern. Pad printing is the pattern on the plate carrier made by plastic head, then transfer the pattern on the plate on the toy products, Pad printing silica gel demand quality exquisite, no impurities, rebounwell, apply oil well, a clear printing pattern Feature of liquid silicone rubber for pad printing 1, Oil fell oil effect is good 2, Exquisite, good resilience, printing more often, no impurities, no particles 3, Printing clear pattern 4, Low viscosity, good fluidity 5, No shrinkage, easy apply oiling , clear printing pattern Precautions of liquid silicone rubber for pad printing No mixing with acid-base materials, alkoxy silane or high temperature water vapor, otherwise there is the tendency of curing and viscosity changes. [ Sample ] We can send 1kg sample for free ,but the shipment charge usually paid by your side [ Rapid response to your needs ] We will be answer within 24hours. Welcome to contact with us if you have any problems.

Supplier: High temperature heat resistant silicone rubber pad,foam silicone rubber sheet,felts for the textile industry,seamless felt,high temperature felt,nomex felt,rotary heat transfer printing seamless blanket
Services: Manufacturer