Temp humidity and vibration test chamber
Temp humidity and vibration compatible Chambers
Vibration Test Chamber
Industrial-quality chambers for combination testing with vibration systems
For years Temp.humidity and vibration compatible Chambers have been the workhorses of the environmental test chamber industry. Originally created to meet military test standards, their flexible design has made them suitable for a wide variety of applications. Fast temperature changes of5 to 25C/m. are possible, even with significant loads. The chambers have a removable floor, allowing integration with vibration test systems. Custom designs are common, allowing configuration to meet your exact requirements.
Special model can interface with both vertical and horizontal vibration systems
In addition, the�touch-screen controller�makes running an Grande environmental test chamber a breeze. The full-color, touch-screen interface is remarkably easy to use and understand. The Touch Screen Controller�can be managed remotely via our new�Ethernet/LAN-based Web Controller, serial port, or GP-IB/Lab View.
Nearly every Agree chamber we build is designed per the application. Here is a review of what is possible with a custom designed chamber f rom Grande.
Feature
Capacity: 63 L to 6000L
Temperature Range: -70 to 180C
Humidity Range: 10-99%RH
Cooling rate: 2-3C/min (standard), 5C/min, 10C/min�, 20C/min as option�
Vibration: maximum up to 5000kgf�, 100g
Temperature Cycling Test Chambers
Fast change rates test chamber
Temperature Cycle Test Chamber
Fast change rates testing chamber is suitable for testing the changes of instruments,electrical,electronic products,machine�and�parts�under�the�rapid�temperature change�or�the�the�gradient�conditions, takes advantage of compact, modern scroll compressors to bring fast temperature cycling to small form factor. Temperature cycling rates from 5 to 20�C/min. are possible. Two different ultimate low temperatures are available: -40�C or -70�C.
The faster cycle times can be used to meet more aggressive test methods that require thermal stress during transitions. Significant test time can be saved in completing tests, as well.
To demonstrate performance, Grande uses the international standard IEC 60068 3-5 measured at the supply air. Temperature cycles are run from hot to cold extremes, and the middle 80% of the transition is timed to determine performance. Your actual cycling results will vary depending on methodology, including the start and end temperatures, and the amount of samples loaded.
Features
QUALITY CONSTRUCTION
Stainless stee l exterior and interior
Rounded interior corners for easy cleaning
Full thermal break around doorframe and door
Rotating door latch is easy and secure
Dual-layer insulation of fiberglass and expanded foam for thermal integrity
One 2" (50mm) to One 4" (100mm) diameter cable port on the left, with an impervious, flexible silicone plug
Easy lift-off service panels
Pressure relief port to allow air volume changes due to rapid temperature changes
Three levels of overheat protection
FTF PROGRAMMER/CONTROLLER
Popular PID controller with touch-screen operation
Stores 120 different profiles�with up to 1200 steps each (ramp, soak, jump, auto-start, end)
Step types include: ramp, soak, jump, auto-start, and end
Ethernet interface for remote monitoring and operation
RECOMMENDED OPTIONS
Dry air purge, to compensate for quickly shrinking air during cooling, as well as to reduce risk of condensation.
Product temperature control, allows feedback from a second sensor on the product. Ensures faster completion of transition steps.
High altitude low pressure simulation test chamber
Altitude Chamber For Sale
Altitude Test Chambers
Temperature testing at altitudes up to 100,000 feet.
Grande can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are:
Testing of avionics or other aerospace equipment to simulate actual conditions it might experience.
Simulation of high-altitude conditions like might be found in mountainous regions.
NOTE: Altitude test chambers are custom systems, and differing requirements may significantly change the cost and utility requirements. Please let Grande know as much detail as possible about your anticipated testing specification/method, and we can provide you with a tailored system for your requirements.
Features
Temperature range from -70 to 200C
Altitude range from ground to 100,000 feet
Optional humidity control when altitude system is off
Chamber interior size specified by customer
Automatic altitude control, integrated with temperature controller No manual setting of altitude level!
Vacuum pum p sized for climb/dive rate required by application
Viewing window and cable ports available
Salt corrosion spray test chamber
Configured for your specific tests
Alternate Salt Corrosion Spray Test Chamber
Grande makes rain and spray testing easier by offering a standard chamber capable of published and OEM proprietary test methods.
The standardized design can be configured for the rain/spray tests you need, eliminating the guesswork in buying a chamber. The system is based on the specification requirements, and can also accomplish individual automakers tests, as well as electrical-enclosure tests.
Our Design
Grande's modular design allows you to add on additional features, depending on the number and type of tests required. One possible choice is to integrate the spray system with a regular temperature and humidity chamber to save money and floor space, while also creating an opportunity to simulate actual operating conditions your product may experience.
Our system uses multiple control solenoids to vary the water's spray volume/pressure. A holding tank prepares the water to the desired temperature, if required. A pump ensures the water is delivered in the proper pressure range. The water is fed to a motorized manifold that rotates the spray arms. Each spray arm has an adjustable valve to allow finer control of the spray.
Testing capabilities
The specification is modeled after and doesnt differ greatly. Details about the nozzle types and the rotating nature of the spray arms and pro duct table are also included in the requirements. Additionally, drip and car wash tests are also specified.
Heavy splash/shower
S1 Spray room temperature water with 40 nozzles at 14.2 psi (1 kgf/cm2) for 30 minutes. The flow rate of the water shall be 6.5 gallons/min. (24.5 L/m).
S2 Spray room temperature water with 40 nozzles at 42.7 psi (3 kgf/cm2) for 60 minutes. The flow rate of the water shall be 10.3 gallons/min. (39.2 L/m).
Light spray/rain
R1 Spray room temperature water with two nozzles at 4.3 psi (0.3 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.8 gallons/min. (3.2 L/m).
R2 Spray room temperature water with two nozzles at 1.4 psi (0.1 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.5 gallons/min. (1.9 L/m).
Examples of OEM automotive manufacturers' requirements
Heat the sample to a temperature above boiling, then spray with cold water for about two minutes. Repeat cycle.
Heat the sample to boiling temperature, then spray with room temperature water for about fifteen minutes. Repeat cycle.
Simulate a car wash by using high pressure spray.
Features
Rotating rain and spray nozzles designed to JIS specifications
Speed control for the rotating spray nozzles
Stationary product shelf - A rotating shelf is optional: see options
Water pressure regulators, gauges and flow meters
Special high-volume floor drain system to rapidly drain water out of the chamber
Interior chamber size is the smallest possible area using the JIS specified nozzles
Applicable Test Methods
HAST PCT high-low temperature test chamber with pressure high pressure accelerated aging testing chamber factory�High Accelerated Stress Test
Steam Aging Test Chamber
Ozone Aging Chamber
Chamber/HAST Chamber
It test the resistance to pressure and air tightness for circuit board, multi-layer circuit board, IC, LCD and magnet iron. This machine is one of the common machine in aging equipment, used to test various types of materials for their performance under the condition of high temperature and high pressure. Application: Quality inspection for all types of electronic products, electric appliance, and products from communication, instrument, metal, plastic, automobile, food, chemical, building materials, medical and aerospace industries.
Pressure Accelerated Aging Test Chamber (HAST)
Safety�Device high pressure accelerated aging testing chamber factory:��
�1.�Safety�device�for�the�pot:�If�the�inner�box�is�not�closed�,�the�machine�can�not�start
�2.�Safety�Valve:�When�the�inner�box's�pressure�higher�than�the�machine's�undertake�value,�it�will�self-relieve.
�3.�Double�overheat�protection�device:�When�inner�box's�temperature�is�too�high,�it�will�alar m,�and�Automatic�cut�off�
the�heating�power.
4.�Cover�protection:�The�inner�box's�cover�is�made�of�aluminum�alloy,�can�protect�the�worker�from�scald.
4348 Laboratory Equipments Instruments Suppliers
Short on time? Let Laboratory Equipments Instruments sellers contact you.
Alternate salt corrosion spray test chamber
Salt Corrosion Spray Test Chamber
Salt Spray Test Chamber
Configured for your specific tests
Alternate salt corrosion spray test chamber adds below functions from traditional salt corrosion spray test chamber:Programmable controllers,accelerated test for copper and acid test.,etc.It complies with Standard of ASTMDIN IEC GJB.
Grande makes rain and spray testing easier by offering a standard chamber capable of published and OEM proprietary test methods.
The standardized design can be configured for the rain/spray tests you need, eliminating the guesswork in buying a chamber. The system is based on the specification requirements, and can also accomplish individual automakers tests, as well as electrical-enclosure tests.
Our Design
Grande's modular design allows you to add on additional features, depending on the number and type of tests required. One possible choice is to integrate the spray system with a regular temperature and humidity chamber to save money and floor space, while also creating an opportunity to simulate actual operating conditions your product may experience.
Our system u ses multiple control solenoids to vary the water's spray volume/pressure. A holding tank prepares the water to the desired temperature, if required. A pump ensures the water is delivered in the proper pressure range. The water is fed to a motorized manifold that rotates the spray arms. Each spray arm has an adjustable valve to allow finer control of the spray.
Testing capabilities
The specification is modeled after and doesn�??t differ greatly. Details about the nozzle types and the rotating nature of the spray arms and product table are also included in the requirements. Additionally, drip and car wash tests are also specified.
Heavy splash/shower
S1 Spray room temperature water with 40 nozzles at 14.2 psi (1 kgf/cm2) for 30 minutes. The flow rate of the water shall be 6.5 gallons/min. (24.5 L/m).
S2 Spray room temperature water with 40 nozzles at 42.7 psi (3 kgf/cm2) for 60 minutes. The flow rate of the water shall be 10.3 gallons/min. (39.2 L/m).
Light spray/rain
R1 Spray room temperature water with two nozzles at 4.3 psi (0.3 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.8 gallons/min. (3.2 L/m).
R2 Spray room temperature water with two nozzles at 1.4 psi (0.1 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.5 gallons/min. (1.9 L/m).
Examples of OEM automotive manufacturers' requirements
Heat the sample to a temperature above boiling, then spray with cold water for about two minutes. Repeat cycle.
Heat the sample to boiling temperature, then spray with room temperature water for about fifteen minutes. Repeat cycle.
Simulate a car wash by using high pressure spray.
Xenon Water-Cooling Aging Test Chamber
UV Aging Test Chamber
Ozone Aging Chamber
Xenon Water-Cooling Aging Test Chamber,is designed to simulate full sunlight spectrum to produce destructive effect on material. The chamber cansimulates the light, temperature, rainfall (spray) and condensing (humidity), ismainly used to test aging resistance of products or spare parts affected by natural environment, it tests the material aging-resistant performance in sunlight, rain, temperature and humidity, you canknow the products quality at a very short time, such as the depigmentation, transmissivity, gloss, peeling, hard, softening.
Specifications:
Xenon arctest chamber
1. We are manufacturer, offer best price for you.
2. Major parts adopt imported brands.
3. LCD touch screen controller, easy operation.
4. Free parts warranty for 12 months.
Features:
1. Equipped with black-board temperature meter to adjust temperature inside the chamber.
2. Xenon lighting time control.
3. Spraying period control.
4. Water recycling.
5. Automatic constancy of water temperature (cooling of recycling water)
6. Spraying, lighting, temperature, humidity and rotating platform can be controlled separately.
7. Equipped with viewing window.
8. Water shortage / over-temperature alarm.
9. Equipped with irradiance meter to show current light intensity inside the chamber.
10.LCD Touch Screen Controller, programmable of temperature, moisture, sun and rain
11.Humidity: 50-98%RH
12.Temperature: RT to 80C(-20 to 80C as option)
13.Blackboard Temperature: 55-100C
14.Light Source: Xenon Lamp
15.Spray Nozzle: 2mm
Features for thermal shock test chamber:
1, thermal shock test chamber - - two-zone is designed to provide two opposite extreme temperature environments for temperature cycling and thermal shock testing of electronic components and assemblies to military specifications.
2, thermal shock testing is achieved by quickly and repeatedly transferring a specimen between a hot chamber and a cold chamber by means of an automatic carriage transport system. The hot chamber is on the left side and the cold chamber is on the right. The cold chamber can be used as a full range test chamber.
3, touch screen programmable controller is produced in korea, perfect performance and stable. Memory capacity is 120 patterns, 999 segments per pattern, and each seg. Can be cyclied 999 times.
4, rs-232 communication interface, it can control / edit / record through computer.
5, all processes are precisely controlled by plc. If any part in machine is malfunction, the whole chamber will shut down and warning light will switch on. Chamber will shut down automatically in case of electrical power instabilities.
Specifications:
-temperature range:-70ºc~+180ºc
-temp constancy: within ±0.5ºc
-temp tolerance: ?¤±2.0°c
Heating time:20ºc??+150ºc ?¤60 min
Cooling time: 20ºc??-70ºc ?¤90 min (no load, average1ºc/min)
Humidity range: 30%~95% rh
Humidity deviation:±3.0%rh(rh>75%rh)
±5.0%rh(rh?¤75%rh)
(remark: above data measured based on ambient temperature is +25ºc, rh is 85%rh, without specimen, constant temperature at 2 hours.)
Features:
Large viewing window with heaters for monitoring the test status anytime.
Stable and user-friendly programmable touch screen controller
Cable access ports (additional ports available upon customer's requirements)
High quality and adjustable specimen shelves
Multi levels safety protection devices
Strict function test and manufacturer's temperature calibration before package
Superb service will be provided
Structures
External: double galvanized metal steel sheet, with spray-paint electrostatic processing surface
Internal: high quality stainless steel with mirror polishing
Insulation: rigid polyurethane foam and glass fiber
Heater: nickel chrome alloy
Features
Rapid design and installation capabilities
Temperatures range: -70â°c to +150â°c
Excellent temperature uniformity.
Built-in reliability: all major sub-systems procured from world class manufacturers.
Easy to use: easy to use graphic interface for test environment setup, through programmable touch screen controller.
-temperature range: -20 degree celsius to 180 degree celsius , -40 degree celsius to 180 degree celsius, -60 degree celsius to 180 degree celsius, -70 degree celsius to 180 degree celsius for optional.
- ramp rate: 1 degree celsius /min
- different size available, from 100l to 1000l.
- excellent temperature uniformity.
- easy to use:friendly human-machine interface
- controller: programmable touch screen controller
-thermal shock temperature range:-20~+150, -40~+150, -65~+150 for optional
-pre-cooling temperature range: rt~-35, rt~-55, rt~-70
-temperature recovery time: â?¤ 5 min
-different size available
-programmable touch screen controller, precise pid control
Test graph
Labtek-3-zone-thermal-shock-chamber-test-graph
Labtek-environmental-test-chamber-features
Large viewing window with heaters for monitoring the test status anytime.
Stable and user-friendly programmable touch screen controller
Cable access ports (additional ports available upon customers requirements)
High quality and adjustable specimen shelves
Multi levels safety protection devices
Strict function test and manufacturers temperature calibration before package
Superb service will be provided
Structures
External: double galvanized metal steel sheet, with spray-paint electrostatic processing surface
Internal: high quality stainless steel with mirror polishing
Insulation: rigid polyurethane foam and glass fiber
New perfect dental lab group is one of the largest dental laboratory in china. Since 1993, we have been working as the outsourcing center for customers from north america, europe and other places . With 17 laboratories and 3, 000 certified technicians, we offer full range of the products to our partners as a one-stop outsourcing center.
Fia8600 quantitative immunoassay analyzer is a medical diagnostic instrument which can be used to measure a variety of biomarkers in human whole blood, serum, plasma or other specimens. Due to its portable and light weight design, the fia8600 can be easily deployed at patient side, facilitating the clinical decisions with its rapid results. Fia8600 offers testing of cardiac markers, inflammation monitoring, diabetes, fertility, and renal function.
Fia8000 quantitative immunoassay analyzer is a medical diagnostic instrument which can be used to measure a variety of biomarkers in human whole blood, serum, plasma or other specimens. Due to its portable and light weight design, the fia8000 can be easily deployed at patient side, facilitating the clinical decisions with its rapid results. Fia8000 offers testing of cardiac markers, inflammation monitoring, diabetes, fertility, and renal function.
The one step test for hba1c (colloidal gold) is intended for use together with the fia8000 quantitative immunoassay analyzer (fia8000). The product employs colloidal gold immunochromatogrphy to determine hba1c in human whole blood specimens. Two monoclonal antibodies are employed to identify hba1c specifically, resulting in a purplish red streak appears on the test line. The color intensity of the test line increases in proportion to the concentrations of hba1c.
Then insert test card into the fia8000 quantitative immunoassay analyzer, the concentration of hba1c is measured quantitatively and displayed on the screen. The result can be transmitted to the lab or hospital information system.
The one step test for hs-crp+crp (colloidal gold) is intended for use together with the fia8000 quantitative immunoassay analyzer (fia8000). The product employs colloidal gold immunochromatogrphy to determine hs-crp+crp in human serum, plasma, whole blood or fingertip blood specimens. Two monoclonal antibodies are employed to identify hs-crp+crp specifically, resulting in a purplish red streak appears on the test line. The color intensity of the test line increases in proportion to the concentrations of hs-crp+crp.
Then insert test card into the fia8000 quantitative immunoassay analyzer, the concentration of hs-crp+crp is measured quantitatively and displayed on the screen. The result can be transmitted to the lab or hospital information system.
The one step test for ck-mb/ctni/myo (colloidal gold) is intended for use together with the fia8000 quantitative immunoassay analyzer (fia8000). The product employs colloidal gold immunochromatogrphy to determine ck-mb/ctni/myo in human serum, plasma, or whole blood specimens. Two set of mixed monoclonal antibodies are employed to identify ck-mb/ctni/myo specifically, resulting in three purplish red streaks appear on the test lines. The color intensity of each test line increases in proportion to the concentrations of ck-mb/ctni/myo respectively.
Then insert test card into the fia8000 quantitative immunoassay analyzer, the concentration of ck-mb/ctni/myo is measured quantitatively and displayed on the screen. The result can be transmitted to the lab or hospital information system.
The one step test for d-dimer (colloidal gold) is intended for use together with the fia8000 quantitative immunoassay analyzer (fia8000). The product employs colloidal gold immunechromatogrphy to determine d-dimer in human plasma, or whole blood specimens. Two monoclonal antibodies are employed to identify d-dimer specifically, resulting in a purplish red streak appears on the test line. The color intensity of the test line increases in proportion to the concentrations of d-dimer.
Then insert test card into the fia8000 quantitative immunoassay analyzer, the concentration of d-dimer is measured quantitatively and displayed on the screen. The result can be transmitted to the lab or hospital information system.
2.Features:
.Sturdy and light weighted copper body
.High quality and accurate testing result
ATC Compensation Range (i.e. Built-in Automatic Temperature Compensation System)
Easy and very convenient to use
4348 Laboratory Equipments Instruments Suppliers
Short on time? Let Laboratory Equipments Instruments sellers contact you.
