Brazilian test apparatus It is also called rock tension testing machine. Brazilian test is a test for indirect measurement of tensile strength of rocks. The instrument is useful for testing specimen from 50 mm dia to 100 mm dia and of thickness of half the diameter. The specimen is held in circular jaws, this is primarily similar to a compression machine and consists of a small load frame having sturdy base with two vertical threaded rods and an adjustable cross head. The hydraulic jack is fitted at the centre of the base of the load frame. The jack of the load frame is self retracting and two plain plates are supplied. A pressure gauge capacity 0-200kn x 2 kn is fixed at the base of jack. A maximum pointer is also provided on the gauge, a pair of semi circular platen for 50 mm dia samples also provided. This instrument can be used in field also. Supplied complete with the steel balls. Order code Product Lisc-563 Brazilian test apparatus with 50 mm dia jaws
Conforms to is: 10050-1981, & astm d 4644 This apparatus is used to assess the resistance offered by a rock sample to weakening and disintegration when Subjected to drying and wetting in a slaking fluid, usually water. The equipment meets the essential Requirements of is:10050 -1981 & astm d 4644 and comprises the following: A motor drive with reduction gear mounted on a base board and capable of rotating four drum assemblies at a Constant speed of 20 rev/min approximately. The motor drive is totally enclosed in a hinged cover for quick Accessibility. An operating switch is provided in the cover. Two / four test drums made of brass wire mesh, with one end closed and having a removable cover on the other End. They have suitable couplings for mounting in the perplex water troughs. The drums are 140 mm in diameter And have an unobstructed length of 100 mm. Two / four perplex water troughs, accommodate one test drum each. These drums carry quick couplings on either End which are in turn coupled with couplings of the motor drive. The troughs allow 40 mm unobstructed clearance Below the test drum. A water level mark is provided in each water trough 20 mm below the axis of rotation of the Drum. Suitable for operation on 220 volts, 50 hz, single phase ac supply. Order code Lisc-557a Lisc-557b No. Of test drums 2 4
Consolidation apparatus (single gang model) Consolidation test is unidimentional test considered extremely important in soil mechanics. Sample taken from adjacent areas of a single site show differential settlement even when tested using same techniques. Soil of similar strength may show varying consolidation. Samples are very carefully prepared and vertical settlement of the specimen in saturated or drained conditions carefully recorded when known load is applied. Specifications: The standard outfit comprises of the following items. Loading unit, maximum capacity 20kg/cm sq. Having a loading yoke connected to a lever arm with a counter balancing adjustment and having a lever ratio of 1:1 the whole assembly being mounted on a sturdy steel frame stand. The loading unit is so designed that it can be used for consolidation cells of different diameters as well as different diameter floating ring type consolidation cells. Fixed ring type consolidometer (odometer) cell assembly for testing 60 mm dia x 20 mm thick specimen Consolidation apparatus (three gang model) Consists of 3 consolidation test assemblies mounted on a single frame. Complete with 3 sets of consolidometer cell assembly for 60mm dia samples and three sets of weights each giving 10kg/sq.Cm. On each sample. Consolidation apparatus (six gang model) Same as above but six units mounted on a single frame.
The direct shear apparatus we offer is designed as per is: 2720 (part-viii), astm d 3080 standards. Direct shear apparatus is extensively used for determining the direct shear strength of soils on specimen size 60mm x 60mm x 25mm. The direct shear apparatus we manufacture is electrically operated to give a 6 rates of strain of 1.25, 0.25, 0.05, 0.01, 0.002 & 0.0004mm/min and is suitable for 230v a.C. Specifications: the apparatus comprises of the following: Loading unit: The loading unit is provided with v strips and roller strips for friction-less movement of shear box housing. Supplied with load yoke with direct and lever system for applying load. Normal stress capacity 8kg/sq.Cm. Load is applied either directly or through a counter balanced detachable lever. Provision is made for the load to be applied either through a steel ball recessed on the pre collaborated loading yoke. Shear box assembly: Comprises direct shear box in two halves for a square specimen size 60 x 60 x 25mm one pair of plain gripper plates, one pair of porous stones, one pair of perforated gripper plates, one top loading pad. Shear box housing: It accommodates the direct shear box assembly. Complete with two ball roller strips. Specimen cutter: Used for cutting 60 x 60 x 25mm specimen from larger samples Set of weights to give a normal stress of 3kg/sq.Cm. Through leverage as follows. To give kg/cm.Sq. Qty. 0.05 - 4 nos. 0.1 - 1 no. 0.2 - 1 no. 0.5 - 3 nos. 1.0 - 1 no. Supplied with essential accessories: 1. High sensitivity compression proving ring cap 200kg 2. One consolidation dial gauge 0.01 mm x 25mm 3. One strain dial gauge 0.01mm x 25mm.
This method is used for determining the ductility of bituminous / asphaltic materials by measuring the elongation before breaking when two ends of a briquette specimen are pulled apart at a speed of 50mm/min ±25mm per mount at a temperature of 25c ± 0.50c. Specifications: The apparatus consists of a water bath with a digital temp. Controller cum indicator, and a circulating pump to maintain uniform water temperature. One half of the briquette moulds is fixed on a fixed plate in the water bath, the other half of the briquette mould is fixed to a carrier which slides over a rotating threaded shaft with a clutch. The motor and gears to rotate the shaft are housed in a cabinet fixed above the other end of the bath. A Pointer fixed to the carrier moves over a scale graduated from 0-110 cm x 1mm fixed on the bath with “0” (zero) of the scale towards the fixed plate side. The rotating shaft has 2 speeds of travel for the bracket, 5cm/min and 1 cm/min. Selected by a clutch. Water bath inside is stainless steel with an insulation and a water drain. A heater with digital temp. Controller cum indicator is fixed inside the water bath. Control switches for motor, stirrer, heater and indicator lamps are fixed at a convenient place on the water bath. Supplied complete with three ductility moulds and one base plate. Operates on 230 volts a.C. Single phase.
Seed counters are extensively used for seed counting in numerous botanical and agricultural laboratories. Features: Accurate counting of seeds. Light weigh. Requires no maintenance. Batching, repeat and multiple batches creating facility. Accurately counts a predetermined number of seed in a single batch count and allows for the continual duplication of a single batch count. Specifications: Display: seven segment fnd display. Seed size: 0.5 mm to 15 mm. No. Of seed: up to 9999 seeds in one batch. Computerized seed counter Specifications: Display: 2x16 column alphanumeric lcd display Seed size: 0.5 mm to 15 mm. No. Of seeds: in one batch: up to 999999 seeds Features: Facility to interface with printer / computer. 15 memory for storing different seed counts. Menu driven with facility for selecting of various seeds. Simultaneous display of preset count and actual count. Multiple batches and totalizing facility available. Auto/manual mode selection available in case of multiple batches. Buzzer indication after every count.
This instrument is used to test the oxidation stability of gasoline and can be used for determination of oxidation stability of petroleum under accelerated oxidation, to evaluate the possibility of colloid generation during oxidation of petroleum products. Our liop-177 gasoline oxidation stability tester comprises with following components: 1. Liquid bath:- square in shape. Inner chamber made of stainless steel and outer made of mild steel duly powder coated. The gap between is thermally insulated. Bath liquid stirring by motorized stirrer. Bath temperature control by microprocessor based controller. There will be provision of placing two number bomb in bath. Fitted with a over heating cutout system and supplied with two number s.S cover to cover the hole of the bath when not in use. 2. Oxidation bomb:- made of stainless steel and highly polished.& glass container. (1 no) 3. Pressure gauge (1no) 4. Quick coupling with oxygen filling device. Features:- 1, the oxidation stability of gasoline tester is compact, easy to operate and comfortable. 2, it can simultaneously accommodate two standard oxygen bomb and easy to assembly and disassemble. 3. Oxygen bombs are made of stainless steel 4, liquid bath is made of stainless steel, rust-proof and durable. 5. The oxidation bath is airtight, no vibration, no noise and no need for fluid replacement during the test. Technical parameters: •Electrical power: 220v± 10% 50hz ac, •Heating power: 2000 w. •Stirring motror1/83 h.P. •Temperature testing range: 105 c. •Temperature accuracy: ± 0.1°c. •Oxygen bomb pressure: range 0 ~ 1500kpa. •Pressure accuracy: 1 f.S. •Sampling time: 1 f.S. Applications: education / research, petroleum industry, power generation etc.
Originated in the Nordic Countries Nord Test is a trademark of conformity assessment. The emphasis of Nord Test is to develop, promote and innovate Nordic test methods and pre-normative activity. SCOPE: This procedure is for determination of the chloride migration coefficient in concrete, mortar or cement-based repair materials from non-steady-state migration experiments. FIELD OF APPLICATION: The method is applicable to hardened specimens cast in the laboratory or drilled from field structures. The chloride migration coefficient determined by the method is a measure of the resistance of the tested material to chloride penetration. This non-steady-state migration coefficient cannot be directly compared with chloride diffusion coefficients obtained from the other test methods, such as the non-steady-state immersion test or the steady-state migration test. DEFINATONS Migration: The movement of ions under the action of an external electrical field. Diffusion: The movement of molecules or ions under a concentration gradient or, more strictly, chemical potential, from a high concentration zone to a low concentration zone. SAMPLING: The method requires cylindrical specimens with a diameter of 100 mm and a thickness of 50 mm, sliced from cast cylinders or drilled cores with a minimum length of 100 mm. Three specimens should be used in the test. TEST METHOD: Principles: An external electrical potential is applied axially across the specimen and forces the chloride ions outside to migrate into the specimen. After a certain test duration, the specimen is axially split and a silver nitrate solution is sprayed on to one of the freshly split sections. The chloride penetration depth can then be measured from the visible white silver chloride precipitation, after which the chloride migration coefficient can be calculated from this penetration depth. Apparatus: • Vacuum container: capable of containing at least three specimens. • Vacuum pump: capable of maintaining a pressure of less than 50 mbar (5 kPa) in the container. • Migration set-up: includes the following parts: – Silicone rubber sleeve: inner/outer diameter 100/ 115 mm, about 150 mm long. – Clamp: diameter range 105 - 115, 20 mm wide, stainless steel. – Catholyte reservoir: plastic box, 370 × 270 × 280 mm (length × width × height). – Plastic support. – Cathode: stainless steel plate about 0.5 mm thick. – Anode: stainless steel mesh or plate with holes about 0.5 mm thick. • Power supply: capable of supplying 0 - 60 V DC regulated voltage with an accuracy of ±0.1 V. • Ammeter: capable of displaying current to ±1 mA. • Thermometer or thermocouple with readout device capable of reading to ±1 °C. • Any suitable device for splitting the specimen. • Spray bottle. • Slide caliper with a precision of ±0.1 mm. • Ruler with a minimum scale of 1 mm. • Equipment for chloride analysis as required by the test method employed.
The Aniline Point of an oil is defined as the minimum temperature at which equal volumes of aniline (C6H5NH2) and the oil are miscible, i.e. form a single phase upon mixing. The value gives an approximation for the content of aromatic compounds in the oil, since the miscibility of aniline, which is also an aromatic compound suggests the presence of similar (i.e. aromatic) compounds in the oil. The lower the aniline point, the greater is the content of aromatic compounds in the oil. The aniline point serves as a reasonable proxy for aromaticity of oils consisting mostly of saturated hydrocarbons (i.e. alkanes, paraffins) or unsaturated compounds (mostly aromatics). Significant chemical functionalization of the oil (chlorination, sulfonation, etc.) can interfere with the measurement, due to changes to the solvency of the functionalized oil. METHOD A: ANILINE POINT APPARATUS as per IP 2 & IS 1448 (P-3), ASTM D 611 METHOD A, complete with jacket (without thermometer) Optional Accessories: • Spare outer jacket with cork Spare tube with cork • Heater for above with energy regulator METHOD B: ANILINE POINT APPARATUS as per IP-2 method B, IS 1448 (P-3), ASTM D 611 by thin film METHOD B, Electrically heated with motorized stirrer (without thermometer). The apparatus consists of an Archimedean type pump ie. glass tube pump body, S.S. pump, variable speed small motor, within an Aniline sample container with an integral light well, illuminated by a 6 V lamp. The whole assembly is heated in small glass beaker bath controlled by energy regulator. Electrically operated stirrer is also provided. Optional Accessories: • Spare tap • Spare Contraction chamber • Spare metal stirrer METHOD C: ANILINE POINT APPARATUS for volatile liquids as per IP-2 method ‘C’ (without thermometer). METHOD D: ANILINE POINT APPARATUS as per IP-2 1977, METHOD D by U-tube method electrically heated with FHP stirrer without thermometer. The apparatus consists of U-tube assembly which is mounted in a glass bath which is heated electrically and controlled by energy regulator. A small electric motor stirrer is provided for the bath. Optional Accessories: • Spare ‘U’ tube Thermometer for Aniline Point: • I.P.20C (-38/42ºC x 0.2C). • I.P.21C (-25/105ºC x 0.2C). • I.P.59C (90/170C x 0.2C).
The apparatus consists of brass test cup with handle removable cup cover with spring operated rotating shutter having oil test jet flame device, stirrer with flexible shaft. The assembly rests in air bath which is covered with dome shape metal top. The cup is fitted with insulated handle and locking arrangement near cup flange. The assemble is kept on round shape electric heater with temp. Regulator. Suitable for operation on 220 volts 50 hz. Pensky marten flash point apparatus (semi automatic) Our semi-automatic pensky martens flash point apparatus are available with following features: This apparatus is made as per ip34, astm d–93 and is 1448 (part i) 1270 (p.21) and is 1209-1953 method b. Used for finding out flash point above 70°c and below 300°c. The instrument having oil test jet (or) gas test jet flame device, stirrer with flexible shaft. The assembly rests in air bath which is covered with dome shape metal top. The cup is fitted with insulated handle and locking arrangement near cup flange. Electronic temperature controller with automatic dipping cycle with remote control oil (or) gas jet. Suitable to operate on 220 volts, 50 hz. Pensky marten flash point apparatus (fully automatic) Fully automatic pensky marten flash point apparatus is fitted with microprocessor controller with lcd display. Temperature range form 80 c to 350 c with 0.01c direct resolution. Automatic stirrer gas test jet system.
Gross volume - 16 l working volume 9 ltrs capacity : 5 kgs motor & control panel - non flame proof additional cost for providing flame proof motor specification: design: mono block cgmp model, contact parts : ss316 other parts : ss304 product container: made out of s316, 2 mm having a dutch mesh in ss316, 2 mm support plate, sight glass, and quick removable type clamps for the dutch mesh and support plate. Trolley: made out of ss304 pipe, 20 nb schedule 10 with 4 nos swivel pu wheels air handling unit consists of inlet filters assemblies housed in a ss304 enclosure to be placed either in the technical. Corridor or on the service floor. It shall have a 5 micron pre filters. Heaters : steam heater assembly or electrically heated model 3 kw electrical load. (hepa filteration provided as optional) filter bag: the machine shall have a 20 micron finger bag made out of pc stain or pp cloth in the filter bag housing chamber, damper manual inlet & outlet dampers blower casing & motor 1.5 hp 2880 rpm motor non flp centrifugal type blower @250 m3hr earthing : standard earthing device (intrincically safe earthing provided as optional) bursting disc: a specially designed bursting disc is provided as a safety against any pressure built up in the main shell. Inlet & outlet ducting if required can be provided at extra cost. Control panel: control panel made in ss304 will be supplied loose or fitted on the machine. The main control panel housing the main contractors, over load relays, mcb's , inlet outlet temperature indicators, process timer and various operating push buttons & lamps finish inside welds ground flush and surfaces shall have mirror polish. External welds ground smooth and surfaces shall have matt finish.
Gross volume - 16 l working volume 9 ltrs capacity : 5 kgs motor & control panel - non flame proof additional cost for providing flame proof motor specification: design: mono block cgmp model, contact parts : ss316 other parts : ss304 product container: made out of s316, 2 mm having a dutch mesh in ss316, 2 mm support plate, sight glass, and quick removable type clamps for the dutch mesh and support plate. Trolley: made out of ss304 pipe, 20 nb schedule 10 with 4 nos swivel pu wheels air handling unit consists of inlet filters assemblies housed in a ss304 enclosure to be placed either in the technical. Corridor or on the service floor. It shall have a 5 micron pre filters. Heaters : steam heater assembly or electrically heated model 3 kw electrical load. (hepa filteration provided as optional) filter bag: the machine shall have a 20 micron finger bag made out of pc stain or pp cloth in the filter bag housing chamber, damper manual inlet & outlet dampers blower casing & motor 1.5 hp 2880 rpm motor non flp centrifugal type blower @250 m3hr earthing : standard earthing device (intrincically safe earthing provided as optional) bursting disc: a specially designed bursting disc is provided as a safety against any pressure built up in the main shell. Inlet & outlet ducting if required can be provided at extra cost. Control panel: control panel made in ss304 will be supplied loose or fitted on the machine. The main control panel housing the main contractors, over load relays, mcb's , inlet outlet temperature indicators, process timer and various operating push buttons & lamps finish � inside welds ground flush and surfaces shall have mirror polish. External welds ground smooth and surfaces shall have matt finish.
E-beam optical coater http://www.pvd-metallizer.com Automatic optical coating equipment equipped with fan-shaped multi-fixtures or vaulted single substrate plate, uses man-machine interface with touch screen plus PLC and automatic crystal thickness control system to realize full automatic control, enabling to achieve functions of parameter input, process monitoring and data storage, etc. So the operation process can be set and the machine runs automatically to achieve the coating repeatability with optical properties of a stable quality. It has solved the complexity of manual operation and the problems of uniformity of film color, optical performance and others. Optical coating equipment can coat multi-layers of short-wave pass, long wave pass, antireflection film (AR), reflective film, filter film, spectral film, band pass film, dielectric film, high reflective film, color reflective film, etc, enabling to achieve 0-99 layers of film coating, also able to meet technical requirements such as automotive reflective light cover, binoculars, glasses, optical lenses, cold-light cups and other products coating. Equipped with different evaporation source, E-beam gun and ion source as well as film thickness monitoring and control system can realize various film coating systems, such as metal, oxide, compound and other high melting point films can be deposited, even super-hard film can be coated on the glass surface. It is extensively used in many fields such as in optical, electronic, decorative industries and in research institute or film research and application fields.
Magnetron Sputtering Deposition Line for ITO Glass The machine line uses two industrial computers and PLC systems to dynamically display the whole operation process with alarm and self-protective functions. The important processing parameters with several optical inspected systems connected to the computer, so the color and thickness of the film can be automatically controlled. ITO Glass coating line: This machine are available to metalize transparent electric conductive film on glass, for example, LCD, PDP display or OLED display, etc. Using vacuum magnetron sputtering deposition technology, with dual cathodes, MF sputtering technology and international advanced control system, it is to deposit SiO2/ITO on the float glass. All the process is automatically controlled in series.
Thermal evaporation metallizer HTTP://WWW.PVD-METALLIZER.COM Vacuum evaporation coating machine is mainly used in coating on the surface of pretreated plastic and ceramic products with metal films (such as aluminum, chrome, stainless steel and other metals), colorful film and imitation gold film etc., as a result. it can obtain bright, beautiful and inexpensive plastic and ceramic metalized products. The machine is extensively used in the industries of lamps, furniture, toys, bottle caps, female shoe heels, car mirrors, crafts, jewelry, watches, cell phones, DVD, MP3, PDA outer coverings, cosmetic shells and Christmas gifts etc. The coating substrates include ABS, PS, PP, PC, PVC, nylon, metal, glass, ceramics and TPU materials, etc. Double Door Vertical Type Thermal Evaporation metallizer is operated by the principle of thermal evaporation by resistance heating that can be used for coating metallic films and gold-imitative films on the pre-treated plastics, ceramics and others in order to obtain bright and good-looking results with lower cost.
Magnetron Sputtering coating line for low-e glass http://www.pvd-metallizer.com Adopting the principle of magnetron sputtering E-discharge, this Vacuum Coating Production Line can coat metallic film or compound films on the surface of large-sized glass, such as curtain wall glass or architectural glass, forming the glass with characteristics of sunshine shelter, temperature keeping, energy saving, low emission and decoration, etc. that has been extensively used high-rank architecture, act wall and room decoration, etc.
Horizontal E-beam optical coater http://www.pvd-metallizer.com To coat optical film or decorative film or functional film on large-sized substrate products such as glass or plastic panels, or to realize mass production of vacuum coating for rhinestone, lamp glass slip, round shape articles as glass tube, lamp tube, the horizontal type E-beam optical coater is the best choice for customers. Horizontal structure E-beam optical coater generally can have large quantity substrate loading with single or double revolution and rotation substrate racks to realize three dimensional moves to make single side coating or all-round uniform coating for round shape substrates.
S&A air cooled chiller CW-5000 for chemical and laboratory S&A brand CW-5000 chiller developed and produced by S&A company of China, it is applied to cool chemical and laboratory equipment. Since January 2016, the warranty period of S&A chiller has extended to 2 years. S&A chiller CW-5000 features 1. 800W cooling capacity; use environmental refrigerant; 2. Compact size, long working life and simple operation; 3. ±0.3? precisely temperature control; 4. The intelligent temperature controller has 2 control modes, applicable to different applied occasions; with various setting and display functions; 5. Multiple alarm functions: compressor time-delay protection, compressor overcurrent protection, water flow alarm and over high / low temperature alarm; 6. Multiple power specifications; CE,RoHS and REACH approval; Chiller parameter: Model CW-5000AG CW-5000BG CW-5000DG CW-5000AH CW-5000BH CW-5000DH CW-5000AI CW-5000BI CW-5000DI Voltage 220V 220V 110V 220V 220V 110V 220V 220V 110V Frequency 50Hz 60Hz 60Hz 50Hz 60Hz 60Hz 50Hz 60Hz 60Hz Current 1.4~2.1A 3.5~5.6A 1~4.8A 3.5~5.6A 1.4~2.1A 3.5~5.6A Compressor power 0.295KW 0.38KW 0.305KW 0.295KW 0.38KW 0.305KW 0.295KW 0.38KW 0.305KW 0.40HP 0.52HP 0.41HP 0.40HP 0.52HP 0.41HP 0.40HP 0.52HP 0.41HP Refrigeration capacity 2361Btu/h 2999Btu/h 2866Btu/h 2361Btu/h 2999Btu/h 2866Btu/h 2361Btu/h 2999Btu/h 2866Btu/h 0.692KW 0.879KW 0.84KW 0.692KW 0.879KW 0.84KW 0.692KW 0.879KW 0.84KW 595Kcal/h 756Kcal/h 722Kcal/h 595Kcal/h 756Kcal/h 722Kcal/h 595Kcal/h 756Kcal/h 722Kcal/h Refrigerant R-134a Refrigerant charge 300g 320g 280g 300g 320g 280g 300g 320g 280g Precision ±0.3? Reducer Capillary Protection Overcurrent protection for compressor, flow alarm, over temperature alarm Pump power 0.03KW 0.051KW 0.1KW Tank capacity 6L Inlet and outlet External F10mm brass connector F10mm speedy connector Max. lift 10 M 12M 25M Max. flow 10 L/min 13L/min 16 L/min N.W 24 Kgs G.W 27 Kgs Dimension 58 x 29 x 47 cm (L x W x H) Package dimension 70 x 43 x 58 cm (L x W x H) Note: other electric sources can be customized; heating and higher temperature control precision functions are optiona . Email:marketing@teyu.com.cn; Website: http://www.teyuchiller.com About S&A Brand S&A produces more than 60000 units of industrial chillers by year,we always insist on”Quality First” in design and production. “S&A” and “TEYU” have been enjoying high reputation among hundreds of manufacturers which are from both at home and abroad,and export rate reaches above 60% -
Classification: Pipette Brand Name: GEB Model Number: AF250A-9-N-S/AF250A-9-N-S-LB Place of Origin: Zhejiang, China (Mainland) Volume: 170ul Material: natural polypropylene Certificate: CE,ISO14001,ISO14000,ISO13485,ISO9001
Classification: Test Tube Brand Name: GEB Model Number: PC0201-B-N /PC0201-B-N-LB Place of Origin: Zhejiang, China (Mainland) Color: Natural Type: Thin wall, flat cap,Low-Retention Certificate: CE
