Liquid Gas Pumps Liquid Gas Pumps are typically centrifugal pumps used to pump liquefied hydrocarbons such as propane, butane, propylene and ethylene. These liquefied hydrocarbons are pumped at -104�°C, and liquefied natural gas (LNG) (usually methane) is pumped at -161�°C, where they remain liquid because above this temperature the gas begins to boil and evaporate. SUNCENTER Liquid Gas Pumps are air driven at a drive air pressure of 2 to 10bar (29 to145 psi) by the normal air compressor. Basically the principle of operation is similar to a reciprocating amplifier where control of the piston at the end position is regulated by a pilot operated 4/2 way valve.
Air Driven Liquid Pump The air driven liquid pump is pneumatically driven reciprocating piston pumps. These air driven liquid pumps are proportional devices that utilize low pressure compressed air to drive a larger diameter piston (area x pressure) that is linearly connected to a smaller hydraulic piston/plunger. Utilizing this ratio principle, higher hydraulic pressure can be generated. Materials of construction include standard all stainless steel wetted ends and polyurethane pressure seals. Specialized materials of construction and special seals are also available upon request. Compact and lightweight, this air driven liquid pump requires no air lubrication and is suitable for water, oil and most chemical applications.
Horizontal Multistage pump sets
ZN series high efficiency new designed dredger pumps are particularly suitable for dredging, filling and other operations in rivers and lakes. It fully meets the requirements of the dredger for mud pumps.They are composed of a pump head, reducer gear box, high elastic coupling, and marine transmission monitoring system.
ZHR rubber liner slurry pump is ideal solution for convey water and solid mixture medium. Suitable for conveying fine particles and corrosive liquids that contain suspended particles. The ZHR series slurry pumps have the features on replaceable wear-resistant metal liners. Basing on medium condition can choose different materials of Natural rubber, Nitrile rubber,Polyurethane etc.
Zidong horizontal slurry pump, centrifugal, double casing structure, international quality, warman replacement pump. It is specially designed to convey solid-liquid mixtures containing high concentration, corrosive and abrasive, hard solid particles, such as: ore slurry, ash, slurry, gravel, etc. It is widely used in mining, metallurgy, power plant, chemical industry, etc.
It is specially used to deal with large particle solids that cannot be handled by ordinary slurry pumps, and mud, gravel and sand with strong abrasiveness; Thickened single pump shell structure, thick pump body; 3- blade closed impeller is designed with larger particles and wider flow passage; The wet parts are made of wear-resistant high chrome alloy, which can efficiently handle large particles, thus reducing costs. Applicable to river dredging, sand pumping, sand mining and other conditions
ZP vertical centrifugal slurry pump, also known as a submerged slurry pump, submerged in liquid, with a vertical cantilevered single pump casing structure and a semi-open impeller. Without any shaft seal and shaft seal water, it can work even in the case of insufficient suction volume. The wet parts are made of high chrome alloy wear-resistant metal, Suitable for conveying dense slurries with large particles and high abrasiveness
"!!! Specific price, Size, Weight Are subject to Inquiry!!!" Competitive brands:|160;rexroth, HAGGLUNDS, AVENTICS, Danfoss, Parker, MOOG, sunhydraforce, EOWARDS, Leybold, INFICON ,NSK and other European and American brands.
"!!! Specific price, Size, Weight Are subject to Inquiry!!!" Competitive brands:|160;rexroth, HAGGLUNDS, AVENTICS, Danfoss, Parker, MOOG, sunhydraforce, EOWARDS, Leybold, INFICON ,NSK and other European and American brands.
"!!! Specific price, Size, Weight Are subject to Inquiry!!!" Competitive brands:|160;rexroth, HAGGLUNDS, AVENTICS, Danfoss, Parker, MOOG, sunhydraforce, EOWARDS, Leybold, INFICON ,NSK and other European and American brands. Products:|160;plunger pump, solenoid valve, gear pump, vane pump, direction valve,
Oil pump is responsible for pressurizing engine oil from oil pan and pumping it throughout the engine. Under pressure from the oil pump, oil purified through oil filter flows properly into various parts of internal combastine engine. BRAND: ATC
When it comes to vacuum and compressor technology, each industry and every application has its own specific needs and requirements. NASH offers unparalleled expertise designing and manufacturing efficient and reliable engineered systems to meet your specific process needs. Each engineered system comes packaged and ready for operation, easily integrating with existing processes and automation systems; minimizing installation and operating costs. Regardless of the application, our broad portfolio of products and technologies ensures that Nash has a solution for you. Whether itâ??s a standard pre-engineered package for general industry, an application specific package for the power industry, or a complete engineered to order hybrid system for the chemical industry; NASH has the experience and expertise to deliver an engineered system that is designed to meet the rigors of even the most demanding applications. Nash liquid ring vacuum pumps and compressors offer the widest performance range on the market. Depending on the size and model, our liquidring vacuum pumps are capable of providing a suction capacity between 10 m�³/hr to 39,000 m�³/hr, with vacuum levels down to 28 mbar abs. Certain models can also be equipped with a center shroud, allowing the liquidring vacuumpump to operate at multiple suction pressures. Our liquid ring compressors are capable of achieving a capacity between 50 and 16.000 m�³/h and discharge pressures from 2 bar abs up to 15 bar abs. In certain applications it is also possible to use the same model for both vacuum and compression. Nash liquid ring pumps are capable of handling a wide variety of gases; from gasoline vapors, sulfur dioxide, and chlorine to hydrogen sulfide and vinyl chloride monomers. Seal liquids can be chosen based on process requirements and the gas being handled. In addition to water, a range of seal liquids including acetic acid, acetone, glycol, xylene, and more can be used.
Shield slurry pump refers to the slurry pump used at shield construction sites. It is named after the working conditions. Just like the slurry pump used at sewage treatment sites, we generally call it sludge return pump, and residual sewage pump. Mud pumps are the same. In fact, our slurry pump is used. So what is shield tunneling? Pansto Pump Industry will first take you to understand shield tunneling construction. The shield construction method refers to the full-section tunnel boring machine tunnel construction method. It is a tunnel construction method that relies on a rotating cutterhead to break the rock through a disc-shaped hob to form the entire tunnel section at one time. Generally, feed pumps and discharge pumps are used at such sites. Because the shield tunnel breaks rocks at the site, the particles are generally larger. In this case, it is generally recommended to use a gravel pump with good performance, or a slurry pump with an AH series open impeller. Because rocks are relatively abrasive, high-chromium alloys with good wear resistance are generally used as materials. The transmission mode is generally DC transmission. The sealing method is mostly sealed with packing. If you want to know more about the shield slurry pump, please contact us! Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
Shield slurry pumps generally use our G-type gravel pumps. The particles in the slurry processed by the gravel pump have larger diameters. When selecting a gravel pump, you should ensure that the particle size requirements that the gravel pump can pass. The gravel pump can adjust the nut to adjust the impeller clearance, reduce loopholes, improve efficiency, and facilitate the disassembly and assembly of the impeller. The current-passing parts are made of high-chromium alloy, which has high hardness, high strength and longer service life than cast iron. A spare blade is used on the back of the impeller to reduce the pressure on the back, reduce the axial force, prevent some debris from entering the seal, and protect the seal from wear. Gravel pump maintenance methods. In order to reduce slurry leakage, the tightness of the packing must be adjusted at any time; the bearing water pressure and water volume must be met according to regulations. Replace bearings promptly. When replacing bearings, make sure they are clean. Ensure the temperature is appropriate during normal operation. Make sure the elastic pads in the coupling are installed correctly. Make sure the direction of rotation of the motor and pump is correct. Make sure the gravel pump assembly and piping system are installed correctly and securely. Pay attention to the degree of wear of flow parts and maintain and replace them in time. If you want to know more about slurry pumps, please feel free to call us! Shijiazhuang Pansto Pump Industry is a manufacturer of slurry pumps in Shijiazhuang. It mainly designs, manufactures and sells slurry pumps and accessories. Mainly engaged in mud pumps, submersible pumps, foam pumps, desulfurization pumps and many other series. Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
In winter, the temperature is low, and the freezing and low-temperature climate caused by rain and snow can easily cause equipment to freeze and crack. In order to ensure the safe and normal operation of the equipment, what do we need to pay attention to. Letâ??s find out. First, insulation materials need to be added to the water pump to prevent the water pump from freezing; Second, empty the slurry in the pump chamber of the water pump that is not in use temporarily, and then refill the pump when in use. This can also effectively prevent the water pump from freezing and cracking; Third, if our slurry pump is in the basement, the doors and windows need to be closed, and the unfinished underground pump room and wind tunnels must be blocked with something. Fourth, because our slurry pumps undergo water closure tests when they leave the factory, there will be water in the pump chamber and pipelines of the factory slurry pumps. If the equipment is not ready to be installed and used, the pump chamber needs to be removed. Drain the water inside. Fifth, when we find that the water pump has become slurry, do not start the slurry pump. You can use hot water or boiling water to pour into the pump cavity to melt the ice, or heat the casing of the water pump. Sixth, if conditions permit, move the slurry pump to a warm place to melt ice naturally. If you want to know more about slurry pumps, please feel free to call us! Shijiazhuang Pansto Pump Industry is a manufacturer of slurry pumps in Shijiazhuang. It mainly designs, manufactures and sells slurry pumps and accessories. Mainly engaged in mud pumps, submersible pumps, foam pumps, desulfurization pumps and many other series. Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
In the north, the temperature in winter can be as low as ten degrees below zero, and in some provinces it can be as low as thirty or forty degrees below zero. It can be said that a drop of water turns into ice. At this time, if our slurry pump is installed outdoors, it will easily freeze or even crack. So how should we antifreeze our slurry pump in winter? Today, Shijiazhuang Pansto Pump Industry will introduce some small methods to prevent freezing in winter. I hope it will be helpful to everyone. 1. Add insulation materials to the slurry pump, such as cotton wool, clothing, etc., and wrap these insulation materials around the pump body to prevent the slurry pump from freezing. 2. Empty the slurry in the slurry pump that is not in use temporarily. Add water before use to prevent slurry in the pump cavity, which may cause the pump body to freeze and crack. 3. Close the doors and windows of the pump room tightly, and attach sealing strips if necessary to ensure the temperature of the pump room. 4. If we find that the slurry pump has frozen, we must not start the water pump. We can use hot water to slowly pour into the pump cavity to melt the ice, or heat the casing of the slurry pump. If you want to know more about slurry pumps, please feel free to call us! Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
The model of the slurry pump is selected based on the flow head provided on site. After the model is determined, the caliber of the slurry pump is also determined. However, the pipelines on site are not designed according to the caliber of the slurry pump. If the size is large What will happen if a large-diameter slurry pump is equipped with a small-diameter pipeline? Let's take a look. Many users think that this can increase the actual lift of the slurry pump. In fact, the actual lift of the slurry pump is the total lift minus the loss lift. When the slurry pump model is determined, the total head is certain; the loss of head mainly comes from the pipeline resistance. The smaller the pipe diameter, the greater the resistance, so the loss of head is greater. Therefore, after reducing the pipe diameter, the actual head of the water pump is not only It cannot be increased, but will decrease, resulting in a decrease in water pump efficiency. In the same way, when a small-diameter water pump uses a large water pipe to pump water, the actual head of the water pump will not be reduced. On the contrary, the loss of head will be reduced due to the reduced resistance of the pipeline, so that the actual head will be increased. Some users also believe that when a small-diameter water pump uses a large water pipe to pump water, the motor load will inevitably be greatly increased. As everyone knows, the liquid pressure is only related to the head and has nothing to do with the cross-sectional area of the water pipe. As long as the head is turned on, the size of the impeller of the water pump remains unchanged. No matter how large the pipe diameter is, the pressure acting on the impeller is certain. However, as the pipe diameter increases, the water flow resistance will decrease, resulting in an increase in flow rate and an appropriate increase in power consumption. But as long as it is within the rated head range, the water pump can work normally no matter how the pipe diameter is increased, and it can also reduce pipeline losses and improve water pump efficiency. If you want to know more about slurry pumps, please feel free to call us! Shijiazhuang Pansto Pump Industry is a manufacturer of slurry pumps in Shijiazhuang. It mainly designs, manufactures and sells slurry pumps and accessories. Mainly engaged in mud pumps, submersible pumps, foam pumps, desulfurization pumps and many other series. Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
The impeller of the sand pump is the main accessory of the entire slurry pump. The flow rate and lift of the pump and the size of the passing particles are directly related to it. In addition to the diameter and width of the impeller, another important parameter is the number of blades. The most common sand pump impellers we have are 3-piece, 4-piece, and 5-piece impellers. The number of blades has a great influence on the flow capacity of the pump. The smaller the number of blades, the larger the particle passing diameter and the stronger the passing performance. We often use it for pumping sand. The slurry contains relatively large pebbles, so a three-blade impeller is usually used. Because there are fewer blades and the greater the spacing between them, the larger the particles that pass through. However, the number of blades is not the only factor that determines the passage of large particles. It is also related to other factors. We should not only look at the number of blades, but also the overall structure of the pump. The number of impeller blades is also related to the efficiency of the pump. The greater the number, the higher the efficiency. The efficiency of large particle sand pumps is generally lower than other pumps with multiple blades. Relatively speaking, if there are no large particles, you can choose 4-blade and 5-blade impellers, which can achieve better efficiency and save costs. If you want to know more about slurry pump accessories, please call us to consult the water pump industry! Shijiazhuang Pansto Pump Industry is a manufacturer of slurry pumps in Shijiazhuang. It mainly designs, manufactures and sells slurry pumps and accessories. Mainly engaged in mud pumps, submersible pumps, foam pumps, desulfurization pumps and many other series. Single-stage slurry pump, slurry pump diagram, slurry pump curve, slurry pump specifications Slurry pump brand Warman slurry pump ZJ slurry pump ZGB slurry pump AH slurry pump SP slurry pump vertical liquid slurry pump
Air Driven Liquid Pump The air driven liquid pump is pneumatically driven reciprocating piston pumps. These pumps are proportional devices that utilize low pressure compressed air to drive a larger diameter piston (area x pressure) that is linearly connected to a smaller hydraulic piston/plunger. Utilizing this ratio principle, higher hydraulic pressure can be generated. Materials of construction include standard all stainless steel wetted ends and polyurethane pressure seals. Specialized materials of construction and special seals are also available upon request. Compact and lightweight, this liquid pump requires no air lubrication and is suitable for water, oil and most chemical applications. Applications High pressure pneumatic liquid pumps are available in a variety of sizes for use in many industries including oil and gas, mining, construction, aviation, aerospace, automotive, biomedical, vegetable oil extraction, alternative energy, chemical, defense, food processing, hydraulic fracturing, and more.
