YLL Vertical Coal Fired Thermal Oil Boiler Coal fired vertical thermal oil boiler use coal as fuel, the heat transfer oils is heated in the boiler first, then the thermal oil flow in a closed loop pipe to the heated equipment and then return to the thermal oil heater again, in this way, the heated object can reach a high temperature (Max. 320?) with indirect heating. It is especially suitable for industies which are flames prohibited Bidragon biomass and wood fired thermal oil heater is high efficient compared with other heating systems. 1. Multi-passes thermal conductive structure to improve the thermal efficiency greatly 2. Horizental tubes can reduce the heat loss. 3. Thicker insulated layer to reduce heat loss by thermal radiation. 4. Intelligent control system makes biomass fired thermal oil boiler operation easier and more simple. Advantage of YLL Vertical Coal Fired Thermal Oil Boiler 1.The oil flow from the lower place to the high place,in this process, the produced gas can easily go out of the system. 2.Automatic feed coal fuel, automatic discharge the slags. 3.Fire grate use independent air chamber, and the air space is larger, so the burning will be more sufficiently.
YGL Coal Fired Thermal Fluid Heater YGL Coal fired thermal fluid heater can reach high temperature (Max. 320?) at low working pressure. It has stable heating performance and precise humidity control system, It also adpots a complete operating control system and safety monitoring devices.
Vertical Thermal Oil Heated Steam Generator The WLE Series steam generator is heated by thermal oil boiler, it is a high efficienty and cost saving system which can provide high temperature and steam at the same time. It is frequently required by factories that they need thermal oil heating system and the steam generator at the same time, and our WLE thermal oil heater can satisfy this requirement. Compared with seperate heating system and steam generator, WLE system reduce the investment cost and maintenance cost greatly. Working Principle When the high temperature thermal oil flows through the tube, the heat will turn the water into saturated steam, the steam will release and be used. Application of Thermal Oil Steam Generator Thermal Oil Steam Generator usually be used with thermal oil heater. Widely applied in food processing, rubber industrial, wood processing, oil production industrial, etc. It can meet the requirement of using one thermal oil heater to get hot thermal oil and steam at the same time which saving a lot of equipment investment and labor cost. It uses the continuous circulated thermal oil to generate steam which can replace the steam boiler.
Steam Accumulator If the boiler can not produce enough steam in production, the accumulator will release steam and the inner pressure will be decreased, then the water will boiling and provide more steam to keep the whole system working under stable condition. Applicable Industry Steam accumulator is widely use in iron and steel industry, metallurgy industry, textile industry, chemical fiber industry, pulp and paper industry, brewing industry, pharmaceutical industry, food processing industry, power generation industry and other industries.
Offering the pricelist and quotation consultation, it is one of the best 1/13 hp - 1/4 hp hydroponic water chillers manufacturers and suppliers in China. Welcome to buy or wholesale 1/13 hp - 1/4 hp hydroponic water chillers from our factory. 1/13 HP - 1/4 HP Hydroponic Water Chillers With Hydroponic Supplies Hydroponic Chillers Performance : ?Chillers are suitable for use in reservoirs, hydroponic systems &fresh or saltwater aquariums. ?Each chiller provides a commercial-grade titanium heat exchanger for optimum performance and corrosion resistance. ?High quality Japanese compressor is extremely efficient and reliable. ?Digital LCD display for easy operation. ?Commercial grade chillers are available to the gardening industry . Why Do You Need a Water Chiller? Well technically, you don't. There are plenty of other ways to cool down your reservoir if you want to save some cash. However... High water temperatures are a consistent problem in many hydroponic setups, especially if you're using a small reservoir in a system like deep water culture. The rising temperatures decreases the amount of dissolved oxygen around the root zone. This in combination with the accelerated growth cycle of plants in a hydroponic environment usually results in oxygen deprivation. That means your plant dies. And dead plants are no good. Along with that, warmer water increases the like lihood that pathogens like pythium take root (pardon the pun) in your system. Chose LANDO Water Chillers for cooling is the best way . Chillers for Hydroponic Systems Product Specification :
Water Cooled UV Curing Systems Shenzhen Lando Company supply for Portable Laser Water Chillers cooled uv led curing systems and Uv Light Curing Equipment.Our Water Chillers Systems which cooling light curing systems ,also our industrial laser water chillers would be application for cooler CO2 tube . UV LED Curing Water Cooled Performance : ?Application : UV LED Curing Water Cooled , UV Printer Chillers or other industrials . ?One-stop automatic intelligent temperature control: in different environment, user does not need to change setting due to it will automatically ?switch to appropriate operating temperature. Voltage:110V-220V; Frequency: 50/60Hz; Refrigerant: R-22 / R-410a Industrial Water Chillers Cool CO2 Laser Tube Main Feature: * Compact thermolysis type industrial water chiller * Long working life and simple operation * Equipped with water flow alarm and over temperate alarm * Radiating capacity: 50W / °C * CE and ROHS certified * Power supply: 110 V or 220 V * Multiple alarm functions: Compressor time-delay protection, compressor over current protection, water flow alarm and over high / low temperature alarm www.lando-chillers.com Email : sales@cnlando.com
KLQ-DZ-type pneumatic furnace lining building machine feature: This machine is a kind of common machine ,size varies,mainly used for 0.5-60T if furnace bottom to knot. Packaging & Shipping Usually delivered by sea shipment container or trucks.
Usage:widely used for engineering machinery, auto parts, fasteners, bearings, chains, metal tools and precision parts industries quenching carburizing. Features: (1)electricity-saving:adopt high tensile calcium silicate board, ceramic fiber board, heat-resistant material for high Performance. (2)operation:adopt automatic control to save manual cost. (3)quality:equipped with a variable step string fan on the top of the furnace to get uniform temperature for high quality. (4) atmosphere:adopt methanol decomposition to stabilize gas and to ensure for quality. (5) stability: cp value tolerance±0.03%(carbon potential), and temperature equally dispersed at ±5?.
Vacuum Casting Furnace Introduction: As the most experienced Vacuum Casting Furnace manufacturer in China, ShinTek Vacuum Casting Furnace can be used for a wide of industries, can melting and pouring Ni-based alloy, special steel, precision alloy, NdFeB, Dysprosium metal, activated metal, super alloy, hydrogen storage material, magnetic material and so on… Vacuum Casting Furnace Specifications: Model STVIM-10 STVIM-25 STVIM-50 STVIM-100 STVIM-200 STVIM-500 STVIM-1000 STVIM-1500 Working zone size 5*3*2 4.8*4*2.5 9.8*5*3.2 9.8*5.5*5.0 11*8.7*4.6 12.5*8*6 16*12*7.6 17*14*8.5 Load (KG) 10 25 50 100 200 500 1000 1500 Power 40KW 50/100KW 100KW 160KW 200/250KW 500KW 500KW 1000KW Voltage 300V 175V 375V 375V 375V 700V 700V 700V Frequency 4000Hz 2500Hz 2500Hz 2500Hz 1600Hz 1000Hz 500Hz 500Hz Max. temperature 1600? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 6.7*10-3Pa Leakage rate =4Pa/h Remark: The Vacuum Casting Furnace can be customized for your specific project. Vacuum Casting Furnace features: (1) Vacuum Casting Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Casting Furnace – Suitable for most of metallurgy industries, can be customized for users; (3) Vacuum Casting Furnace – Two heating system are available for choose, either thyristor frequency converter or IGBT power system. (4) Vacuum Casting Furnace – Two feeding method for choose: Manual or Semi-continueous; (5) Vacuum Casting Furnace – Friendly control system.
Vacuum Furnace Introduction: ShinTek can produce varieties of Vacuum Furnaces, including Vacuum heat treatment Furnace, Vacuum Brazing Furnace, Vacuum Sintering Furnace, Vacuum Induction Melting Furnace and so on… Vacuum Heat Treatment Furnace: Vacuum Quenching Furnace, Vacuum Annealing Furnace, Vacuum Tempering Furnace, Vacuum Carburizing Furnace, etc... Vacuum Brazing Furnace: Vacuum Aluminum Brazing Furnace, Vacuum High Temperature Brazing Furnace, Vacuum Diffusion Brazing Furnace, etc... Vacuum Sintering Furnace: Vacuum Powder Metallurgy Sintering Furnace, Vacuum MIM Sintering Furnace, Vacuum Hot Pressing Furnace... The Vacuum Furnace can be used for a wide of industries, including High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy, Ti alloy, Beryllium Bronze, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal, magnetic material, nonferrous metal, etc… Vacuum Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.67 Pa/h Vacuum Furnace features: (1) Vacuum Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Furnace – Friendly control system.
Vacuum Annealing Furnace Introduction: ShinTek Vacuum Annealing Furnaces can be used for annealing varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Annealing Furnace Specifications: Model STVF-A-80 STVF-A-100 STVF-A-150 STVF-A-200 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 80KW 100KW 150KW 200KW Max. temperature 1100? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Annealing Furnace can be customized for your specific project. Vacuum Annealing Furnace features: (1) Vacuum Annealing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Annealing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Annealing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Annealing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Annealing Furnace – Friendly control system.
Vacuum Brazing Furnace Introduction: ShinTek can produce varieties of Vacuum Brazing Furnaces, including Vacuum Aluminum Brazing Furnace, Vacuum High Temperature Brazing Furnace, Vacuum Diffusion Brazing Furnace and so on… Our Vacuum Brazing Furnaces can be used in a wide of industries, including Stainless Steel, Copper alloy, high temperature alloy, Titanium alloy, Hard metal, ceramic metallization, silver-copper, aluminum, nickel alloy, electric radar board antenna, radiator, compensation, PTC heater, oil radiator, plate-fin heat exchanger and so on… Vacuum Brazing Furnace Specifications: Model STVF-AB-120 STVF-AB-200 STVF-AB-380 STVF-AB-580 Working zone size 1000*600*600 2100*900*900 3000*900*900 5800*1000*1200 Load (KG) 500 2000 3000 6000 Power 120KW 200KW 380KW 580KW Max. temperature 750? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.4 Pa/h Remark: The Vacuum Brazing Furnace can be customized for your specific project. Vacuum High Temperature Brazing Furnace: Model STVF-B-65 STVF-B-120 STVF-AB-150 STVF-AB-220 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 65KW 120KW 150KW 220KW Max. temperature 1320? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.5 Pa/h Remark: The Vacuum Brazing Furnace can be customized for your specific project. Vacuum Brazing Furnace features: (1) Vacuum Brazing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Brazing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Brazing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Brazing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Brazing Furnace – Friendly control system.
STAF-1400 Series Controlled Atmosphere Furnace The STAF-1400 series Controlled Atmosphere Furnaces are customized for some specific applications in the labs. They can be used for varieties of industries, such as the electronic ceramic sintering, glass annealing or crystallization, ceramic metallization, powder metallurgy, technological material innovation and so on… Features: 1. Double-layer wall, equipped with air-cooled system, enable a quick temperature rising or decreasing rate; 2. A Perfect high-temperature sealing kits on the cover and top; a water cooling system is equipped in the cover; 3. There is a gas inlet, a gas outlet, a hole for pre-vacuum pump system on the furnace body. 4. Furnace body: Steel plate 5. The heat barrier system: Al2O3 polycrystalline fibre by a patent assembly way, enable a 50% energy saving. 6. Heater: silicon carbide rod 7. Intelligent temperature control system; 8. Can filled with Hydrogen, Argon, Nitrogen depend on your specific application. 9. Equipped with pre-vacuum pump system, can achieve a pre-vacuum level of 20kPa; 10. Pressure after filling with gas (Argon, Hydrogen, Nitrogen): 0.1MPa Specifications: Atmosphere Furnace STAF-1400-5 STAF-1400-8 STAF-1400-10 STAF-1400-16 Power consumption 5KW 8KW 10KW 16KW Voltage 220V 220V/380V 380V 380V Frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz Working zone size (mm) 200*150*150 300*200*200 400*300*300 500*400*400 Max. temperature 1400 ? Working temperature 1300-1350? Temperature rising rate =20 ?/min, adjustable Temperature uniformity +/-5? Temperature accuracy +/-1? Heater silicon carbide rod Temperature control sys Intelligent PID Unit price (USD, Ex-works) 7,380.00 8,360.00 10,820.00 14,300.00 Remark 1.) The working zone size, temperature or other functions can be customized per user’s specific requirements; 2.) An additional wet hydrogen system costs around 1000 USD. Payment terms: 1.) 100% paid by T/T before production; or 2.) 50% paid by T/T (advance), balance 50% paid by T/T before delivery (after inspection) . Or 3.) 100% paid by L/C (confirmed and irrevocable, at sight) before production.
STAF-1700 Series Controlled Atmosphere Furnace The STAF-1700 series Controlled Atmosphere Furnaces are customized for some specific applications in the labs. They can be used for varieties of industries, such as the electronic ceramic sintering, glass annealing or crystallization, ceramic metallization, powder metallurgy, technological material innovation and so on… Features: 1. Double-layer wall, equipped with air-cooled system, enable a quick temperature rising or decreasing rate; 2. A Perfect high-temperature sealing kits on the cover and top; a water cooling system is equipped in the cover; 3. There is a gas inlet, a gas outlet, a hole for pre-vacuum pump system on the furnace body. 4. Furnace body: Steel plate 5. The heat barrier system: Al2O3 polycrystalline fibre by a patent assembly way, enable a 50% energy saving. 6. Heater: MoSi2 rod 7. Intelligent temperature control system; 8. Can filled with Hydrogen, Argon, Nitrogen depend on your specific application. 9. Equipped with pre-vacuum pump system, can achieve a pre-vacuum level of 20kPa; 10. Pressure after filling with gas (Argon, Hydrogen, Nitrogen): 0.1MPa Specifications: Atmosphere Furnace STAF-1700-6 STAF-1700-8 STAF-1700-15 STAF-1700-25 Power consumption 6KW 8KW 15KW 25KW Voltage 220V 380V 380V 380V Frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz Working zone size (mm) 200*150*150 300*200*200 400*300*300 500*400*400 Max. temperature 1700 ? Working temperature 1600? Temperature rising rate =20 ?/min, adjustable Temperature uniformity +/-5? Temperature accuracy +/-1? Heater MoSi2 rod Temperature control sys Intelligent PID Unit price (USD, Ex-works) 9,630.00 11,885.00 13,520.00 15,640.00 Remark 1.) The working zone size, temperature or other functions can be customized per user’s specific requirements; 2.) An additional wet hydrogen system costs around 1000 USD. Payment terms: 1.) 100% paid by T/T before production; or 2.) 50% paid by T/T (advance), balance 50% paid by T/T before delivery (after inspection) . Or 3.) 100% paid by L/C (confirmed and irrevocable, at sight) before production.
Vacuum Carburizing Furnace Introduction: ShinTek Vacuum Carburizing Furnace can be used for Quenching and Carburizing varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Carburizing Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Carburizing Furnace can be customized for your specific project. Vacuum Carburizing Furnace features: (1) Vacuum Carburizing Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Carburizing Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Carburizing Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Carburizing Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Carburizing Furnace – Friendly control system. The main difference between Oil Quenching and Gas Quenching: 1. Oil Carburizing – Total investment is lower; 2. Gas Carburizing – Small deformation on the parts after treatment; Do not need clean after treatment.
Vacuum Heat treatment Furnace Introduction: ShinTek can produce varieties of vacuum heat treatment furnace, including Vacuum Quenching Furnace, Vacuum Annealing Furnace, Vacuum Tempering Furnace, Vacuum Carburizing Furnace etc…which can be used for heat-treating varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Heat Treatment Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Heat treatment Furnace can be customized for your specific project. Several hotzone design for choose: Horizontal, Vertical; Vacuum Heat Treatment Furnace features: (1) Vacuum Heat Treatment Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Heat Treatment Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Heat Treatment Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Heat Treatment Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Heat Treatment Furnace – Friendly control system.
Vacuum Induction Melting Furnace Introduction: As the most experienced Vacuum Induction Melting Furnace manufacturer in China, ShinTek Vacuum Induction Melting Furnace can be used for a wide of industries, can melting and pouring Ni-based alloy, special steel, precision alloy, NdFeB, Dysprosium metal, activated metal, super alloy, hydrogen storage material, magnetic material and so on… Vacuum Induction Melting Furnace Specifications: Model STVIM-10 STVIM-25 STVIM-50 STVIM-100 STVIM-200 STVIM-500 STVIM-1000 STVIM-1500 Working zone size 5*3*2 4.8*4*2.5 9.8*5*3.2 9.8*5.5*5.0 11*8.7*4.6 12.5*8*6 16*12*7.6 17*14*8.5 Load (KG) 10 25 50 100 200 500 1000 1500 Power 40KW 50/100KW 100KW 160KW 200/250KW 500KW 500KW 1000KW Voltage 300V 175V 375V 375V 375V 700V 700V 700V Frequency 4000Hz 2500Hz 2500Hz 2500Hz 1600Hz 1000Hz 500Hz 500Hz Max. temperature 1600? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 6.7*10-3Pa Leakage rate =4Pa/h Remark: The Vacuum Induction Melting Furnace can be customized for your specific project, and also can be equipped with casting furnace for your melting and casting process. Vacuum Induction Melting Furnace features: (1) Vacuum Induction Melting Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Induction Melting Furnace – Suitable for most of metallurgy industries, can be customized for users; (3) Vacuum Induction Melting Furnace – Two heating system are available for choose, either thyristor frequency converter or IGBT power system. (4) Vacuum Induction Melting Furnace – Two feeding method for choose: Manual or Semi-continueous; (5) Vacuum Induction Melting Furnace – Friendly control system.
Vacuum Quenching Furnace Introduction: ShinTek Vacuum Quenching Furnace includes vacuum oil quenching furnace and vacuum gas quenching furnace, which can be used for quenching varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Quenching Furnace Specifications: Model STVF-Q-40 STVF-Q-65 STVF-Q-85 STVF-Q-120 STVF-Q-160 STVF-Q-240 STVF-Q-500 Working zone size 450*300*300 600*400*400 750*500*500 900*600*600 1100*700*700 1200*800*800 3500*800*600 Load (KG) 60 150 250 500 800 1000 2500 Power 40KW 65KW 85KW 120KW 160KW 240KW 500KW Max. temperature 1350? Temperature uniformity +/-5? (can achieve +/-3?for some specific project.) Ultimate vacuum level (Cold) 8*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Quenching Furnace can be customized for your specific project. 1. Several hotzone design for choose: Horizontal, Vertical; 2. Single chamber, Twin chamber, Three chamber; Vacuum Quenching Furnace features: (1) Vacuum Quenching Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Quenching Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Quenching Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Quenching Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Quenching Furnace – Friendly control system. The main difference between Oil Quenching and Gas Quenching: 1. Oil quenching – Total investment is lower; 2. Gas quenching – Small deformation on the parts after treatment; Do not need clean after treatment.
Vacuum Tempering Furnace Introduction: ShinTek Vacuum Tempering Furnaces can be used for Tempering varieties of materials, such as High Speed Steel, Die Steel, Alloy Steel, Aluminum and Aluminum alloy die, Ti alloy, Precision alloy, Stainless Steel, High temperature alloy, refractory metal, hard metal etc… Vacuum Tempering Furnace Specifications: Model STVF-T-80 STVF-T-100 STVF-T-150 STVF-T-200 Working zone size 600*400*400 750*500*500 900*600*600 1200*800*800 Load (KG) 200 300 500 1000 Power 80KW 100KW 150KW 200KW Max. temperature 1100? Temperature uniformity +/-5? Ultimate vacuum level (Cold) 5*10-4 Pa Leakage rate =0.67 Pa/h Remark: The Vacuum Tempering Furnace can be customized for your specific project. Vacuum Tempering Furnace features: (1) Vacuum Tempering Furnace – Patented hotzone design enable a high energy efficiency; (2) Vacuum Tempering Furnace – High vacuum level, enable it can be used for a wide of industries; (3) Vacuum Tempering Furnace – Several kinds of heating elements for choose, customized for your specific projects: Graphite, SS, Ni-Cr, Mo, MoLa, TZM, Tungsten… (4) Vacuum Tempering Furnace – Reasonable hotzone design enable a high temperature uniformity; (5) Vacuum Tempering Furnace – Friendly control system.
Equipment Main Characteristics Our company established in 1995, has more than 10 years experience in making resistance welding machines and induction heating equipment. To meet the demand of heating needs, we developed the KIA-1KW mini induction heater with our partner This device adopt Electro-Magnetic induction theory, can fast heat small metal parts on auto or machines. Mainly used for heating Rusted/ Frozen/ Corrosive Bolt, Nut, Fasteners, Suspension Nut, Gears, Pulley, and Bearings etc. Meanwhile, it also can help removing stickers on cars. Heating Abilities: In around 30 seconds, it can heat a 20mm diameter bolt to a temperature above 300 C, maximum temperature can reach around 750 C. The advantage if using this device is it is totally flameless, comparing with traditional way of heating by fire, it is much safer and of higher work efficiency, without the worry of harming the adjacent area. Light weight, do not need water cooling, and very easy to use. Main technical parameters Model Number KIA-1KW Certificate CE(EMC,LVD),UL,CCC, Available for COC, POVC Rated Voltage 110V/220V AC 50/60Hz Rated Power 1000W Induction Coil Diameter Quantity 30mm2(PCS), 40mm 2(PCS), 50mm 2(PCS), Spare Wire 2(PCS) Heating Bolt Diameter 5-40mm Plug Type Type H, Type B, Type G, Type E Net Weight 1.3KG Heater Dimension 30cm 6.8cm 6.8cm
