These breakers, which are used as primary and secondary, are ideal crushers to break the materials with high mohs hardness (materials of river and basalt). They break the materials by compressing them with two fixed and movable jaws. If the materials into the machine are hard to be broken, then the jaw crushers do not harm themselves through the safety plates which will be broken in a certain load. The main body is manufactured from tension and high-pressure resistant sheets/materials. Material crusher jaws and side liners are produced from the 16% - 18% manganese, 1.5% molybdenum alloy steel castings.
PSK series crushers, which are jaw-adjusted impact crushers, are crushers that break medium and high hardness materials (such as limestone, dolomite, granite and basalt) in the size of asphalt and concrete aggregate. Coarse material feeding, cubic product, high reduction ratio, high capacity, low investment and operating cost have made this type of crusher the ideal secondary crusher in crushing and screening plants. The stone entering the crusher hits the crushing elements in the first region with the swing of the rotor hammers and the first crushing stage takes place. In this region, high pressure and breaking power are created to break even very hard materials. If the crushed material is in the desired dimensions, it passes to the second zone. The material passing to the second zone passes through another crushing stage and is reduced to smaller sizes. Then the material passes to the third and last zone and the final crushing process takes place. Now the material is reduced to the smallest dimensions. ADVANTAGES Wear-resistant crushing elements High crushing capacity High reduction rate Hydraulic body opening Possibility to use both sides of the pallets
- FULLY-AUTOMATIC SPREADING Specific to the automatic models with precise flow adjustment and specially designed spray-bar, perfect spreading can be made. The system works by reading the data such as vehicle speed and spread width by providing instantaneous pump flow for the desired amount of spreading. Spreading width can be increased or decreased during operation, the operator can accelerate or slow down according to the condition of the road, while the operator is focused on the driving system can start, maintain, and finish spreading. - COMPLETE CONTROL FROM CABIN Thanks to the specially designed control panel located in the operator's cab, the operator can get all functions such as circulation, automatic/manual spreading, intermediate pump feature, system cleaning, as well as controls such as pneumatic spray-bar locks, positions, paving width and spray bar movement of the spray bars. - ASPHALT PUMP The body of the asphalt pump is designed to remain in the tank so that freezing in the pump is prevented. Thanks to the internal valves on the pump, the system performs all functions without the need for a complicated piping system. Maintenance and cleaning are provided much more quickly and easily. - PUMP FUNCTION With a dedicated Asphalt Distributor Pump, critical functions can be performed with valves that are located both inside the pump and at the piping. Pneumatic actuators can be controlled directly from the cabin. Re-Suction TankFilling Tank Circulation Automatic / Manual Spraying Tank Discharge Intermediate pump (allows the transfer of the material from one source to another without mixing with the material in the tank using the Distributor) â?¢ System Cleaning - SAFE & FAST HEATING 8 diameter 2 flame tubes are placed along with the tank in U format. With 2 units of the electric burner, the material is heated quickly and efficiently. - SOLID MECHANICAL JOINTS The mechanical joints are important for the sealing and long-life use of the spray bar. Connectors used in the VAD Series asphalt Distributor allow the entire spray bar to be raised, lowered, or moved sideways. - OPTIONAL THERMAL OIL SPRAY-BAR HEATING SYSTEM The oil is heated by using the burners in the bitumen tank and transmitted to the spray bar. This eliminates the risk of material cooling during and after the spreading. - WORLDWIDE DELIVERY AND ONSITE INSTALLATION VAD Series Asphalt Distributors are designed according to the request of our customers to be suitable for their own countriesâ?? new or second-hand trucks. So, the high truck import expenses will be reduced. VAD Series can be put pre-montaged into a 40ft container thanks to this design transportation costs are reduced significantly and it took only 5-7 days for the installation and training.
Tertiary impact crushers are high-speed machines that are used to obtain sand. The material entered into the machine exits the machine after that it is hit against the walls and crushed by a high-speed (800 r / min) rotor. The material generally left over the screen is broken in these crushers, which usually are used to obtain 0-5 mm sand.
VSI crushers are the tertiary type of crushers used to crash the hard and abrasive materials between 0-45 mm, bring them into cubic shape and obtain sand. VSI crushers are produced in two types as closed rotor and open rotor. The vertical shaft types of crushers with closed rotor are fed with stones maximum size of 0-45 mm. because some large material in return of the crashed material can leave on the screen; these types of crushers are not suitable for crashing the returned material. VSI crushers shoot and crush the material, which entered into the rotor, by throwing them to the lining of stones "stone box" which formed in the stator naturally and to the materials which entered in the system from the outside of the rotor with a speed of 67 - 80 m / s approximately (crushing stones by hitting stones). VSI crushers are used to crush the materials having hardness lower than the grade 9 with a moisture content of less than 9%. Non-flammable and non-explosive mining materials have to be used.
Vibrating feeders are with each other synchronized two pieces of feeders which built solidly, supported with heavy duty suspension springs, driven/actuated by vibromotor, these feeders enable the transmission of the tuvenane materials, brought from the quarry, into the primer crushers in an orderly manner. They throw the mixed soil part of the tuvenian material outside of the system through the intermediate size adjustable grids on the front part of the feeders which coated with mangan. By demand, the loss of materials can be included in the system again after screening them with a suitable screen it is possible. The feeding capacity adjustment of vibromotor vibrating feeders, produced by us, can be made. Thus, the primary machine is fed regularly, and again there is no need to stop and run the machine continuously.
Point Makina is manufacturing tissue converting machines at its own modern production facilities in Istanbul, Turkey.
Point Makina is manufacturing tissue converting machines at its own modern production facilities in Istanbul, Turkey.
Tyent ionization machine ACE-11 Turbo has 11 electrolysis plates. It generates about 20% more antioxidants and minerals than if you choose a Tyent ACE-9 Turbo, which has two smaller electrolysis plates.
Descaler for coffee machines. COMPOSITION: Citric acid, lactic acid. INSTRUCTIONS: 1) Empty the water tank and pour in 100ml of EcoDescaling Solution. 2) Dilute the100ml of descaler with water; the quantity is indicated in the coffee machine user manual (if there is no indication, use 1 litre of water). 3) Start the descaling cycle as explained in the manual. 4) Rinse the tank out several times with clean water, as explained in the machine instructions. WARNINGS: One dose (100ml) is always sufficient for perfect descaling. The descaler may damage delicate surfaces. If the product seeps out, rinse it off immediately. Read the instructions carefully and always keep them handy. Do not use other products that are not suitable for descaling.
More light! New Design. Guillotine Glass Systems are automatic and manual glass panes with unique vertical working characteristics. Guillotine Glass Systems are used as window or glass railing in the door, inside space as window or rail. The guillotine glass system is modified to suit the intended use. Guillotine Glass is a durable and functional automatic glass system developed to provide perfect ease of use in indoor and outdoor living spaces. It can be used integrated with our Pergola and Aluminum Panel systems. With its simple and elegant design, the system makes passive spaces comfortably usable in winter conditions. For more information on our company and products, please feel free to contact our International Sales Team.
Classic Pergola (VENUS PERGOLA) The Venus Pergola is made of special high tenacity aluminum alloy. Produced by electrostatic painting. Produced from different construction carrier, resistant to adverse weather conditions. This is the awning system that makes available areas in winter conditions. TECHNICAL DETAILS German Becker or Somfy Motor Inox construction and connection screws. Black-out resistant and water repellent for all weather conditions Advanced Mehler brand surface material consists of PVC block. Durability wind 90km/h and durability snow height average 30cm. Aluminum rail thickness 145x100cm. Backfurrow size 150x175cm. Dolumn rail thickness 100x160cm. Width range from 300sm to 1100sm, Projection range from 300sm to 1100sm All products have different types, sizes, colors. For more information on our company and products, please feel free to contact our International Sales Team.
Ideal solution for strip cutting from tubular fabric. Standart triple strip cut. (optionally increasable) Cutting different sizes at the same time with adjustable knives. Adjustable diameter of strip rolls. Automatically stop after reaching the required diameter. Save space with 1m2 working area. Easy movement with directional wheels Speed control Low power consumption. Easy maintenance.
Coal Packing Plant
External Fixation Systems consist of various components used to build constructs to treat the indications listed below. External Fixation Systems are modular, therefore, different frame configurations are possible. An individualized configuration should be designed for each case to suit the specific application. All External Fixation System components are for single use only. Each External Fixation System is designed as a system and does not allow the substitution of components from other systems.External Fixation Systems are made from aluminium and stainless steel. It utilizes circular frame and half-pin fixation techniques and procedures for placement of the device. The device is intended to be centered on the axis of rotation. The device allows some adjustability to permit adjustment on the axis.
The mortar mixing machine is a machine that mixes and thicken the acrylic mortar used in the production of 1000 kg jambs.
Bevelling machine 10 wheels as is With washer Min. Dim.: 110x110 mm (40x40 with special device) Thickness: from 3 to 25 mm
Chocolate Coating Machine QUALTY : All parts of the machine are produced from 304 qualty stainless steel materials SYSTEM : The drum system. Push-up roller mixer. Speed control.Control panel. Chocolate thinning fan. Wire tape up to 40 cm POWER : Wire tape 0,75 kW mixer 1,1 kW output transfer drum 0,75 kW DIMENSION : Width 99 cm - Height 108 cm - Length 120 cm WEIGHT : 270 kg CAPACITY : 100 kg
CVS Fuel Protection Systems is produced for prevent fuel theft 100% protection Commercial vehicles mainly working with diesel and gasoline (truck, bus, minibus,midibus, Construction Machinery, generator, motorcycle, Yacht, Boat, etc.) products and systems that prevent diesel theft from vehicle groups.
Automatic stretch blow molding machine APF - 30 to produce PET bottles. Output - 250 bph. Bottle volume - 10.0 - 30.0 L
