Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Thinner 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating. Recommended Use :- This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application. Physical Data COLOUR : Industrial Shades FINISH : Glossy / Semi-glossy SOLIDS BY VOLUME : 40 + 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr @ recommended DFT of 30 FLASH POINT : Base : Above 23 C Hardener : Above 23C DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base: Hardener - As per our recommendations APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Type 290 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30- 40 . OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is an ideal primer where faster turnaround of equipment is desired, Hence making it ideal primer for industrial and Infrastructure equipments, heavy machineries etc exposed to medium corrosive and marine environment. It is also recommended for steel structures in Chemical, Fertilizers, Petrochemical and industrial plants. Not to be used for immersion application. Physical Data :- COLOUR : Grey, Yellow, Beige, Red oxide FINISH : Egg Shell SOLIDS BY VOLUME : 48 ± 3% (Depends on shade) THEORETICAL SPREADING RATE : sq.mt / lit at recommended DFT of 30 µ FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : DRY TO HANDLE: 3 hr's max FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30 - 40 µ. OVERCOATING INTERVAL : MIN : 2 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous Top coats.
Description Two Component, Air-drying, Epoxy Polyamide Cured Finish Paint. Recommended Use :- It Is Recommended As A Top Coat For Structures, Pipelines, Vessels, Equipments And Machineries, Storage Tanks Etc. In Fertilizers And Chemical Plant, Cement Plants, Power Plants, Steel Plants, Pharmaceutical And Petrochemical Complexes, Refineries Etc. Product Is Also Recommended For Application Over Suitable Primer For Oem Industry Like Machine Tools, Pumps, Machineries, Transformers Etc. Physical Data Colour : assorted Shades Finish : glossy / Semi Glossy Solids By Volume : 40 +3% (depends On Shade) Theoretical Spreading Rate : 13.33 Sq.mt / Ltr At Recommended Dft Of 30 au Flash Point : base: Above 23 C Hardener: Above 23 C Drying Characteristics (at 30'c And 65% Relative Humidity) : hard Dry : Overnight Full Cure : 7 Days Shelf Life : base : 6 Months Hardener : 6 Months Surface Preparation This Being A Topcoat, Which Is Applied Over, Primer Or Intermediate Coats, The Surface Should Be Free From Oil, Moisture, Dust And Dirt. Aged Epoxy / Pu Coating Should Be Roughened By Emery Paper Grade 400 / 600 For Better Bonding. Application Data :- Mixing Ratio : base : Hardener (as Per Our Recommendation) Application : by Brush / By Conventional Spray / By Airless Spray Thinner : 190 Pot Life : 4-6hrs Min At 30 C Recommended Dft : 30-40 U Over Coating Interval : min : 8 Hours Max : 24 Hours Compatibility : can Be Over Coated With Pu, Chlorinated Rubber And Synthetic Enamel Paints.
Description Two component, air-drying, Epoxy polyamide cured finish paint. Recommended Use :- It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc. Physical Data COLOUR : Assorted Shades FINISH : Semi glossy SOLIDS BY VOLUME : 40 �± 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr at recommended DFT of 30 �µ FLASH POINT : Base: Above 23�° C Hardener: Above 23�° C DRYING CHARACTERISTICS : SURFACE DRY : 90 minutes max HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : 190 POT LIFE : 4-6hrs min at 30 �° C RECOMMENDED DFT : 30-40 �µ OVER COATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with PU, Chlorinated rubber and synthetic enamel paints.
Description Two-component air-drying intermediate/primer surfacer coat. Recommended Use :- Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats. Physical Data :- COLOUR : Grey, White FINISH : Egg Shell to Matt SOLIDS BY VOLUME : 40 �± 3% SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ FLASH POINT : Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting. Application Data :- MIXING RATIO : Base: Hardener ( As per our recommendation) APPLICATION : By Brush/ By Conventional Spray / By Airless Spray THINNER : Type 290 POT LIFE : 4 hours min at 30�° C RECOMMENDED DFT : 30 -35 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
Description Two component air drying aromatic polyurethane finish coating Recommended Use :- It is recommended as topcoat for Original Equipment Machines, Hygienic, Maintenance painting where mild chemical resistance along with good abrasion resistance and decorative finish are required. Sometimes it is recommended as undercoat of finish coats application for economic benefits. Physical Data COLOUR : Assorted shades FINISH : Glossy / Semi glossy / Matt SOLIDS BY VOLUME : 40 �± 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 FLASH POINT : Base : Above 23C Hardener : Above 30C DRYING CHARACTERISTICS : SURFACE DRY :20 - 30 minutes (At 30C and 65% Relative humidity) HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a Topcoat, which is applied over underneath primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 followed by solvent wipe for better bonding. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional spray / By Airless Spray THINNER : Type 290 POT LIFE : 3 hours min at 30 C RECOMMENDED DFT : 30-40 OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Nano Acrylic Cement Primer is water based, Economical interior primer with good whiteness,good coverage and flow and leveling properties. RECOMMENDED APPLICATION Nano Acrylic interior wall primer that can be suitable for priming plastered wall,asbestose,cement concrete etc. PRODUCT TECHNICAL DATA No COLOURS White 1. FINISH Smooth and matt 2. COVERAGE 1 coat: 90-100 sq.ft/ltr 2 coats: 60-70 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc.) 3. DRYING TIME Surface drying time â?? 10-15 minutes 4. GLOSS LEVELS/SHEEN LEVELS NA 5. FLASH POINT (IS101/108 Part 1, Sec 9) Non- flammable 6. SUITABILITY OF THINNER PAINT Use within 24 hrs. 7. SHELF LIFE 12 Month from date of manufacture in original tightly closed containers away from direct sunlight and excessive heat.
ULTRA PREMIUM weatherproof interior and exterior emulsion is a smooth, water-based, modified acrylic, interior and exterior wall finish with silicon additives. FEATURES :- ULTRA PREMIUM weatherproof interior and exterior emulsion is specially formulated to withstand extreme tropical conditions of rainfall, humidity and heat ULTRA PREMIUM provides excellent resistance from growth of algae and fungi on the walls. This prevents appearance of black spots due to algal growth. ULTRA PREMIUM provides extremely good protection against alkali and UV degradation, thus ensuring that the shade doesnâ??t fade for a long time and the paint lasts longer. RECOMMENDED USE :- ULTRA PREMIUM Acrylic interior and exterior emulsion is interior and exterior wall finish that can be applied on all type of smooth plaster, asbestos sheets, concrete etc. PRODUCT TECHNICAL DATA :- COLOURS : White & other shades FINISH : Smooth and soft sheen COVERAGE : On smooth primer masonry surface by brushing 1 coat: 140-170 sq. ft/ltr 2 coats: 85-95 sq.ft/ltr (It may vary due to factors such as methods and conditions during application and surface roughness etc) DRYING TIME : Surface drying time â?? 30 minutes GLOSS LEVELS/SHEEN LEVELS : Silky smooth with soft sheen FLASH POINT (IS101/108 Part 1, Sec 9) : Non- flammable SUITABILITY OF THINNER PAINT Use within 24 hrs. SHELF LIFE 18 month from date of manufacture in original tightly closed containers kept away from direct sunlight and excessive heat. PERFORMANCE DATA :- ABRASION RESISTANCE : Excellent WATER RESISTANCE : Excellent REMARKS : 1) Store the product at ambient conditions in well ventilate locations and away from the source of ignition and fire. 2) Avoid eye and skin contact. In case of eye and skin contacts wash with plenty of clean water. 3) Do not inhale or inject. In case of inhalation move to fresh air and seek medical attention. 4) Use protective equipments like rubber/polythene gloves, safety goggle/glasses, face mask while handling the paint-this is required for all paints. 5) In humid areas, use of a bio-wash solution is recommended to remove surface fungus growth, fungal spores, mould etc. before application of the paint system. 6) Do not apply when ambient temperature is less than 10�ºC or if the temperature might drop to this level within 4 hrs of application. 7) Tinted paints need thorough shaking/mixing immediately after tinter addition as well as before use. 8) For removing stains, sponge clean with a mild soap solution and wipe clean. Ensure drying time of 1 Week before cleaning.
Description SAFFRO MELLOW COATINGS & RESINS MELLOWTEX RUSTIC/DHOLPURI/BUBBELS is a textured finish composed of high quality durable acrylic modified resin specially designed as an intermediate coating. RUSTIC imparts a super premium look to the walls. BENIFITS :- Hides Fine Cracks It hides surface undulations and fine cracks. Tough Textured The tough texture finish lasts for long and ensures low maintenance. Plaster Protection It increases the life of plaster by protecting it from wind driven rain. UV Resistance It has excellent UV resistance and adhesion. Anti-algal Formula It resists fungal and algal growth when applied as system, with the recommended top coat. Technical Information :- Drying time: Surface dry time 30 - 60 min. Flash point IS101/1987 Part 1, Sec 6: NA. Coverage :- Pre-painting Steps Plaster New masonary surfaces must be allowed to cure completely. It is recommended to allow 28 days as the curing time for new masonary surfaces. Cleaning Surface should be free from any loose paint, dust or grease. Growths of fungus, algae or moss should be removed by wire brushing and water. When the underlying surface exhibits chalkiness, in spite of thorough surface cleaning, use Saffroâ??s Exterior Primer. How To Apply :- On normal masonary surface by a trowel spatula to obtain an even coating of 1 to 1.5 mm ,2 coats 2 to 2.5 sq.ft/kg** (**Actual coverage may very from the quoted coverage due to factors such as method and condition of application and surface roughness and porosity.) Filling For Holes & Dents :- In case of dents and holes use Saffro Mellow Coatings & Resins SUMO Acrylic Wall Putty or white cement and fine sand in the ratio 1:3. Saffro Mellow Coatings & Resins,MELLOW TEX RUSTIC should not be applied on surfaces / substrates that are subjected to continuous seepage or dampness.
Two component air drying Epoxy based clear primer with Polyamide as curing agent. Recommended Use :- This product is recommended as penetrating primer on bare concrete, wooden substrate prior to application of subsequent coating system. Physical Data :- COLOUR : Clear FINISH : Smooth & Glossy SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 20 sq.mt. / ltr. at a recommended DFT of 25 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Thorough surface preparation is vital. For best results, saffro recommends mechanical preparation techniques (Eg. mechanical scarifying, grit or sand sweeping), a) New Concrete Surface :- New concrete surface should be at least 28 days old and/or have moisture content of less than 5% before proceeding with primer application. Laitance and deposits on new concrete are best removed by light grit blasting, mechanical scarification or grinding. Acid etching may be considered for smaller areas, after etching the floor, it should be thoroughly washed with clean water, and then allowed to dry. b) Old Concrete Floors :- Mechanical cleaning methods are strongly recommended on old concrete surfaces, particularly their heavy contamination by oil and grease has occurred or old coatings is present. To ensure good adhesion, all contaminants are removed and the surface thoroughly cleaned of all dust and loose debris. A thorough detergent wash is also recommended followed by thorough cleaning with water and moping it off to a dry state.
Looking for Garment Stock Buyers Unit Price: USD 4.46/pc EXW or USD 4.68/pc FOB CHINA Available Stock : 2,000pcs Fabric: 100% Polyester Colors: White, Grey, Dusty Orange Size: XS-XXL Original Market: USA Payment Terms: 30% Deposit, Balance before shipment Remarks: (1) No quantity details. Exact breakdown available if buyer is seriously interested with a deposit. (2) We will pay full amount to factory after deposit received, and check breakdown in our warehouse. (3) seaship or airship, to be confirmed by buyer.
Packaging options: 20 ml jar (available for a palette of 70 colors) Wholesale from 1 kg (available palette of 1950 colors)
Fabric -Non Denim/Crape Size - 34.36.38.40.42.44 (Inches) With Hanger & Cover
Elegant Women Unique Blazer For Women
Various interior and exterior paints. All eco-friendly products Same quality as European products while nearly a half price from their prices 30 years of know-how and experiences
Material : %86 Polyester %14 Elastane Color : Cream Size : S-M-L-XL
Material : 82 % Polyester 18 % Polyamide Color : Salmon Size : S-M-L-XL
Material : 86% Polyester , 14% Elastane Color : Pistacchio Size : S-M-L-XL
%89 Polyester %23 Viskoce %8 Elastane Sax S-M-L-XL
